BayTech BayTech DS62 Manuel utilisateur

2019

COPYRIGHT2019

BayTechnicalAssociates,Inc

1/1/2019

DATASWITCHDS62/DS62‐MD4

QUICKSTART

Page2

QUICKSTART:DS62/DS62MD4SERIES

SerialConnection

SetupIPAddress

This is the bare minimum for Ethernet Control. If this is a new unit shipped directly from Baytech, follow

the steps. If this is a previously own unit, perform a factory reset to clear out any users and passwords still

in the unit. The System Administrator should tell you to use DHCP or provide you an IP Address, Subnet

Mask, and Gateway Address. NOTE: default IP Address is 0.0.0.0

Connect to the Serial port (EIA232) using the supplied rollover flat cable and adapter.

Use terminal emulation software to access the unit, (i.e. Microsoft Hyper-terminal, PUTTY). Set the

PC serial port configuration to the following: 9600 bps, 8 data bits, 1stop bit and no parity.

Module: 1

Attention Character: ;

Device A (2 ,1).........1

Device B (2 ,2).........2

Device C (2 ,3).........3

Device D (2 ,4).........4

DS-RPC (3 ,1).........5

Status..........................S

Configure.......................C

Unit Reset......................RU

Logout..........................T

Enter Request :C

If you get only a blinking cursor Press ‘Enter’. If still only

a blinking cursor, Type 5 Attention Characters, (factory

default is the semi-colons {;}). The Attention Character

will not echo on the screen. There is a one second delay

before the menu is displayed. You should see a menu

similar to the right.

Type ‘C’ at the ‘Enter Request’ prompt and press Enter

You should see the menu to the right.

Type ‘1’ and Enter Request prompt and pres Enter

onfiguration

DS62 module #1..........1

DS74 module #2..........2

DS-RPC module #3..........3

Enter Request : 1

DS62-MD4 Ethernet Host Module

Revision F 3.06.01 Module 1

Hardware 1.01 Serial number 423789 colilo version 1.05.01

Status..........................1

Serial Port Configuration.......2

Serial Port Device Name.........3

Attention Character.............4

Disconnect Timeguard............5

Connect Port ID Echo............6

Network Port Configuration......8

Module Name.....................9

RPC Management.................10

Firmware / Config Download.....11

Modem Configuration............12

Exit............................X,CR

Enter Request :8

You should see the menu

to the right.

Type ‘8’ and Enter

Request prompt and pres

Enter

Page3

etwork setup :

Ethernet Address................ 00:C0:48:06:77:6D

IP Address...................... 0.0.0.0

Subnet Mask..................... 0.0.0.0

Default Gateway................. 0.0.0.0

Connection Inactivity Timeout (mins): Disabled

Carriage Return Translation: Disabled

Break Length (msecs): 350

DHCP is Enabled Telnet is Enabled SSH is Enabled

SSH host keys are set to factory default

IP Address........................1

Subnet Mask.......................2

Gateway Address...................3

Inactivity Timeout................4

Carriage Return Translation.......5

Break Length......................6

DHCP Enable/Disable...............7

Telnet Enable/Disable.............8

SSH Enable/Disable................9

SSH Host Key Generation...........10

IP Filter Configuration...........11

SNMP Configuration................12

Web Server Configuration..........13

Exit..............................X,CR

Enter Request :

You should see the menu to the right.

Default ‘DHCP’ is enabled. To enter a

STATIC IP address DHCP must be

disabled.

Type ‘7’ and Enter Request prompt and

pres Enter

You should see the menu to the right.

Type ‘N’ and Enter Request prompt and

pres Enter

DHCP is...........................Enabled

Enable ? (Y/N), CR for no change) :

etwork setup :

Ethernet Address................ 00:C0:48:06:77:6D

IP Address...................... 0.0.0.0

Subnet Mask..................... 0.0.0.0

Default Gateway................. 0.0.0.0

Connection Inactivity Timeout (mins): Disabled

Carriage Return Translation: Disabled

Break Length (msecs): 350

DHCP is Disabled Telnet is Enabled SSH is Enabled

SSH host keys are set to factory default

IP Address........................1

Subnet Mask.......................2

Gateway Address...................3

Inactivity Timeout................4

Carriage Return Translation.......5

Break Length......................6

DHCP Enable/Disable...............7

Telnet Enable/Disable.............8

SSH Enable/Disable................9

SSH Host Key Generation...........10

IP Filter Configuration...........11

SNMP Configuration................12

Web Server Configuration..........13

Exit..............................X,CR

Enter Request :

You should see the menu to the right.

Type ‘1’ and Enter Request prompt and

pres Enter

Page4

1. Connect to the Serial port (EIA232) using the supplied rollover flat cable and adapter.

2. Use terminal emulation software to access the unit, (i.e. Microsoft Hyper-terminal, PUTTY).

Set the PC serial port configuration to the following: 9600 bps, 8 data bits, 1stop bit and no

parity.

3. If you get only a blinking cursor Press ‘Enter’. If still only a blinking cursor, Type 5 Attention

Characters, (factory default is the semi-colons {;}). The Attention Character will not echo on

the screen. There is a one second delay before the menu is displayed. You should see a menu

similar to (Figure 1).

4. Select ‘C’ for the configuration menu. You should see a menu similar to (Figure 2).

5. Select the number for ‘Login Setup’ option. You should see a menu similar to (Figure 3).

6. Select the number for ‘Manage Users’ option. You should see a menu similar to (Figure 6).

7. NOTE: The ‘root’ user can not be deleted.

8. Select ‘A’ to add user. Type the name and password at the prompts.

9. Press ‘Enter’ until get to the ‘Login Setup Menu’ (Figure 3).

10. Select ‘Access Control’ to enable or disable the Tenet and Serial Login Prompt (Figure 4).

11. Press ‘Enter’ until you get the Configuration menu (Figure 2).

12. Select ‘Network Port Configuration’ option. You should see a menu similar to (Figure 7).

13. If your System Administrator requires you to use DHCP, then select ‘DHCP Enable/Disable’

and type “Y” to enable DHCP. Continue to next step. If you wish to assign a static IP

address to this unit, disable the DHCP and go to step 17.

14. Press ‘Enter’ until you are asked to ‘Accept Changes’. Type “Y” to accept changes or “N” to

decline changes.

15. After Accepting or Declining Changes you should get the Network Access Menu (Figure 1).

16. Select ‘Unit reset’ to update the external connections. Once the reset is completed (1 minute)

connect the Baytech device to your network using an Ethernet cable.

17. If you disabled the DHCP in step 13, you should see a menu similar to (Figure 7).

18. Select the ‘IP Address’ option and type the assigned IP address and press ‘Enter’.

19. Select the ‘Subnet Mask’ option and type the assigned subnet mask address and press ‘Enter’.

20. Select the ‘Gateway Address’ option and type the assigned Gateway address and press ‘Enter’.

21. Press ‘Enter’ until you are asked to ‘Accept Changes’. Type “Y” to accept changes. You

should get the Network Access Menu (Figure 1).

22. Select ‘Unit reset’ to update the external connections. Once the reset is completed (1 minute)

connect the Baytech device to your network using an Ethernet cable.

23. You should be prompted for a user name and password, similar to (Figure 5)

At this point you have enough basic configurations needed to operate this Baytech unit.

Page5

Universal Ethernet Controller Configuration:

Figure 1: Network Controller

Figure 2: Network Configuration

Figure 3: Network Login setup

Module: 1

Attention Character: ;

Device A (2 ,1).........1

Device B (2 ,2).........2

Device C (2 ,3).........3

Device D (2 ,4).........4

DS-RPC (3 ,1).........5

Status..........................S

Configure.......................C

Unit Reset......................RU

Logout..........................T

Enter Request :

DS62 Ethernet Host Module

Revision F 2.25.06 Module 1

Hardware 1.00 Serial number 22222 colilo version 1.05.01

Status..........................1 Status of all network options

Serial Port Configuration.......2 Setup the Serial port EIA232

Serial Port Device Name.........3 Change the EIA232 port name

Attention Character.............4 Type 5 times to access Network Main menu.

Disconnect Timeguard............5 Data received within the delay period,

is data, not attention character; thereby

preventing unwanted port disconnection

Connect Port ID Echo............6 Echo port name or module# & port#

access control, manage users

Network Port Configuration......8 Network Port IP Address

Module Name.....................9 Change name of module

MSP Management.................10 Set up Voltage/Current/Sensor threshold

Firmware / Config Download.....11 Update Firmware, SSL, Configuration files

Exit.........................X,CR

Enter Request :

Access Control..................1

Manage Users....................2

Radius Configuration............3

TACACS Configuration............4

Exit............................X,CR

Access Menu: The Access Menu screen, allows for Outlet Operations, Network Configuration, or

Disconnection. To access the Network Configuration Screen, type five Attention Characters.

NOTE: For initial network access, the IP address, subnet mask, and gateway must be

configured from the serial port. Default setting is 0.0.0.0.

Page6

Access Control

Figure 4: Network Access Control

Figure 5: Network Login Prompt

Manage Users

Figure 6: Network Manage Users

Network Port Configuration

Figure 7: Network Port Configuration

Enable or disable usernames and passwords for network, serial, and DS62MD4 modem port access. If

any login has been enabled you will get a prompt similar to the following:

Telnet Login Prompt Enable/Disable..1

Serial Login Prompt Enable/Disable..2

Modem Login Prompt Enable/Disable...3 DS62-MD4 only

Add/delete users and change their passwords. Usernames and passwords are case sensitive and

alphanumeric. The root user can not be removed.

User Management Menu

To change user password or port access, enter number of user.

To add/delete user, select appropriate menu choice.

SNMP V3 requires passwords that are between 8 and 31 characters long

Enter request, CR to exit menus.

A)...Add user

1)...root

etwork setup :

Ethernet Address................ 00:C0:48:00:01:FD

IP Address...................... 70.150.140.89

Subnet Mask..................... 255.255.255.224

Default Gateway................. 70.150.140.65

Connection Inactivity Timeout (mins): Disabled

Carriage Return Translation: Enabled

Break Length (msecs): 350

DHCP is Disabled Telnet is Enabled SSH is Enabled

SSH host keys are set to factory default

IP Address........................1

Subnet Mask.......................2

Gateway Address...................3

Inactivity Timeout................4

Carriage Return Translation.......5

Break Length......................6

DHCP Enable/Disable...............7

Telnet Enable/Disable.............8

SSH Enable/Disable................9

SSH Host Key Generation...........10

IP Filter Configuration...........11

SNMP Configuration................12

Web Server Configuration..........13

Exit..............................X,CR

DS62 login:

Password: The default user and password is “root/baytech”, all lower case.

For network access, you must configure the IP addresses, Subnet Mask, and Gateway Address, or

enable the DHCP. The Changes must be saved and the module reset for network changes to take effect.

Page7

Select each menu option, press ‘Enter, then select next option and press ‘Enter’, i.e. {Network Status: (C/1),

type ‘C’ (Configure) at prompt and press ‘Enter’, type ‘1’ (Status) at prompt, and press ‘Enter’.

Network Menu Configure: (C)

Network Status: (C/1)

Serial Port Configuration: (C/2)

Handshaking: (C/2/1)

Baud Rate: (C/2/2)

Word Size: (C/2/3)

Stop Bits: (C/2/4)

Parity: (C/2/5)

RTS/DTR Line Driver Inactive State: (C/2/6)

Modem DCD Connection Mode (DS62-MD4 ONLY): (C/2/7)

Serial Port Device Name: (C/3)

Attention Character: (C/4)

Disconnect Timeguard: (C/5)

Connect Port ID Echo: (C/6)

Access Control: (C/7/1)

Telnet Login Prompt Enable/Disable: (C/7/1/1)

Serial Login Prompt Enable/Disable: (C/7/1/2)

Manage Users: (C/7/2)

Add user: (C/7/2/A)

Delete user: (C/7/2/5)

root: (C/7/2/1)

Direct Port Connection: (C/7/3)

Radius Configuration: (C/7/4)

Radius Enable: (C/7/4/1)

Radius Server Address: (C/7/4/2)

Radius Backup Server Address: (C/7/4/3)

Radius Secret: (C/7/4/4)

Enable URPC usernames as backup: (C/7/4/5)

Radius Login Timeout: (C/7/4/6)

Radius Server Port: (C/7/4/7)

TACACS Configuration: (C/7/5)

TACACS Enable: (C/7/5/1)

TACACS Server Address: (C/7/5/2)

TACACS Backup Server Address: (C/7/5/3)

TACACS Secret: (C/7/5/4)

Enable URPC usernames as backup: (C/7/5/5)

TACACS Encryption Enable: (C/7/5/6)

TACACS Login Timeout: (C/7/5/7)

TACACS Server Port: (C/7/5/8)

URPC Privilege Level Enable: (C/7/5/9)

URPC Privilege Level: (C/7/5/10)

Network Port Configuration: (C/8)

IP Address: (C/8/1)

Subnet Mask: (C/8/2)

Gateway Address: (C/8/3)

Inactivity Timeout: (C/8/4)

Page8

Carriage Return Translation: (C/8/5)

Break Length: (C/8/6)

DHCP Enable/Disable: (C/8/7)

Telnet Enable/Disable: (C/8/8)

SSH Enable/Disable: (C/8/9)

SSH Host Key Generation: (C/8/10)

IP Filter Configuration: (C/8/11)

SNMP Configuration: (C/8/12)

SNMP Trap Host 1 Address: (C/8/12/1)

SNMP Trap Host 2 Address: (C/8/12/2)

SNMP Trap Host 3 Address: (C/8/12/3)

SNMP Trap Host 4 Address: (C/8/12/4)

SNMP Read-Only Community: (C/8/12/5)

SNMP Read-Write Community: (C/8/12/6)

SNMP Enable: (C/8/12/7)

SNMP v3 Only Enable: (C/8/12/8)

SNMP Authentication Traps Enable: (C/8/12/9)

Web Server Configuration: (C/8/13)

Web Enable: (C/8/13/1)

Web Login Enable: (C/8/13/2)

Web SSL Enable (Secure Comm): (C/8/13/3)

Web Login Activity Timeout: (C/8/13/4)

Module Name: (C/9)

RPC Management: (C/10)

Temperature Alarm Threshold: (C/10/1)

Under Voltage Alarm Threshold: (C/10/2)

Over Voltage Alarm Threshold: (C/10/3)

Low Current Alarm Threshold: (C/10/4)

Environmental Sensors: (C/10/5)

Outlet Groups: (C/10/6)

List Outlet Groups: (C/10/6/1)

Add Group: (C/10/6/2)

Delete Group: (C/10/6/3)

Rename Group: (C/10/6/4)

Modify Outlets in a Group: (C/10/6/5)

Delete All Outlet Groups: (C/10/6/6)

Temperature units (degrees C/F): (C/10/7)

Power Factor Threshold: (C/10/8)

1 2/1 MMP11

2 All Inputs/Circuits/Outlets - Power Factor Threshold

3 All Inputs/Circuits/Outlets - Power Threshold

Firmware / Config Download: (C/11)

Enable Firmware Upgrade: (C/11/1)

Enable SSL Cert Upload: (C/11/2)

Enable Configuration File Upload: (C/11/3)

Restore Configuration Defaults: (C/11/4)

Get Current Configuration File: (C/11/5)

Display Configuration Error Log: (C/11/6)

Enable Rel Ctl. Firmware Upgrade: (C/11/7)

MMP11 (2 ,1).........1

Modem Configuration Menu (DS62-MD4 ONLY): (C/12)

Page9

Modem Port Configuration (DS62-MD4 ONLY): (C/12/1)

Rings to Auto Answer (DS62-MD4 ONLY): (C/12/2)

Modem Connectivity Timeout (DS62-MD4 ONLY): (C/12/3)

Modem Inactivity Timeout (DS62-MD4 ONLY): (C/12/4)

Modem Device Name (DS62-MD4 ONLY): (C/12/5)

PPP Configuration (DS62-MD4 ONLY): (C/12/6)

Country Code (DS62-MD4 ONLY): (C/12/7)

Autres manuels pour BayTech DS62

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels BayTech Changer

BayTech

BayTech DS73 Manuel utilisateur

BayTech

BayTech BayTech DS71-MD4 Manuel utilisateur

BayTech

BayTech DS72 Manuel utilisateur

BayTech

BayTech DS74 Manuel utilisateur

BayTech

BayTech DS Series Manuel utilisateur

BayTech

BayTech ATS27 Manuel utilisateur

BayTech

BayTech MRPr Manuel utilisateur

BayTech

BayTech DS-RPC Manuel utilisateur

BayTech

BayTech DS3 Manuel utilisateur

BayTech

BayTech MSP Series Manuel utilisateur

BayTech

BayTech V79 PDI-1 Manuel utilisateur

BayTech

BayTech BayTech DS62 Manuel utilisateur

BayTech

BayTech ATS Series Manuel utilisateur

BayTech

BayTech DS2-RPC Manuel utilisateur

BayTech

BayTech MMP Manuel utilisateur

BayTech

BayTech BayTech DS71-MD4 Manuel utilisateur

BayTech

BayTech MMPr Manuel utilisateur

BayTech

BayTech DS2-RPC Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur