Barco CLM W6 Manuel utilisateur
CLM W6/HD6
Service Manual
Barco nv Events
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.88.24
E-mail: [email protected]
Visit us at the web: www.barco.com
This manual applies to Barco CLM W6/CLM HD6 projection system. The manual helps you
to get a brief description of basic technical information in service and maintain the product.
Your customers will be appreciate the quick response time when you immediately identify
problems that occur with our products. We expect your customers will be appreciate the
service that you offer them.
This manual is for technicians and people who have an electronic background. Please
send the product back to the distributor for repairing and do not attempt to do anything
which is complex or is not mentioned in the troubleshooting.
Notice:
The information found in this manual is subject to change without prior notice. Any
subsequent changes made to the data herein will be incorporated in future edition.
CLM W6/CLM HD6 Service Manual
Copyright Jan. 2012
All Rights Reserved
Manual Version 3.0
Preface
CLM W6/CLM HD6 Jan 31, 2012 I
Table of Content
Chapter 1 Introduction
Highlight 1-1
System block diagram 1-4
Main board connection diagram 1-5
Chapter 2 Disassembly Process
Equipment Needed & Product Overview 2-1
Disassemble Projector Lens 2-2
Disassemble I/O COVER 2-3
Disassemble Main Board Module 2-5
Disassemble Lamp Module 2-8
Disassemble Color Wheel Module 2-10
Disassemble Front Cover Module 2-12
Disassemble Front Cover Shielding 2-14
Disassemble Top Cover 2-15
Disassemble Top Cover Shielding 2-15
Disassemble Keypad Board Module 2-16
Disassemble Connector Board 2-18
Disassemble Right Lamp Driver 2-22
Disassemble Dual lamp blower module 2-25
Disassemble Front dual lamp blower module 2-28
Disassemble ROD and DA blower module 2-30
Disassemble Blower Bracket 2-31
Disassemble Engine Module 2-32
Disassemble Fan (70*20) 2-42
Disassemble LVPS Module 2-45
II CLM W6/CLM HD6 Jan 31, 2012
Table of Content
Disassemble Left Lamp Driver 2-45
Disassemble Fan Module (120X120X25 mm) 2-48
Disassemble Fan Module (105X32 mm) 2-49
Disassemble Blower Module (60X25 mm) 2-51
Disassemble Right Air Vent 2-52
Disassemble Left Air Vent 2-52
Disassemble Bottom Cover Module 2-53
Rod Adjustment 2-56
Chapter 3 Troubleshooting
LED Lighting Message 3-1
Equipment Needed 3-3
Main Procedure 3-4
Power Troubleshooting 3-5
Image Performance Troubleshooting 3-7
Remote Control Troubleshooting 3-11
Network Troubleshooting 3-12
Chapter 4 Function Test & Alignment Procedure
Test Equipment Needed 4-1
Service Mode and Hidden Menu 4-1
OSD Reset 4-2
Reset Lamp Hour 4-2
Test Condition 4-3
CLM W6/CLM HD6 Jan 31, 2012 III
Table of Content
Test Inspection Procedure 4-5
PC Mode 4-6
Calibration 4-9
Video Performance 4-11
Keystone Test 4-12
PIP Function Test 4-13
Network Function Test 4-13
Others 4-17
Chapter 5 Firmware Upgrade
Section 1: System Firmware Upgrade
Equipment Needed 5-1
Firmware Upgrade Procedure 5-2
Section 2: Network Firmware Upgrade Procedure
Equipment Needed 5-6
Read Projector IP 5-7
Network Setting 5-8
PC Hardware Link 5-9
Section 3: Re-write Serial Number
Equipment Needed 5-11
Re-write Serial Number Procedure 5-12
Appendix A Exploded Image I
Appendix B (S/N Denition) I
1-1
CLM W6_CLM HD6 Jan 31, 2012
Chapter 1 Introduction
1. Introduction
1-1 Highlight
No Item Description
1 Dimensions (L x W x H) • 550 x 436 x 236 (mm)
2 Weight • < 25 Kg
3 Power Supply Meets Japanese power distribution requirements:
Mains voltage range: 100V-240V (+/- 10%)
Mains frequency range: 50Hz/60Hz
4 Keystone correction • +/-30 degree
5 Brightness
Brightness with Different Optional Lens:
• WT91-Wide: Typical 6000 lm
• WT91-Tele: Typical 5344 lmTypical 5344 lm
• WT93-Wide: Typical 5648 lm: Typical 5648 lm
• WT93-Tele: Typical 52�1 lm: Typical 52�1 lm
• WT96-Fixed:Typical 5896 lm:Typical 5896 lm
• WT95-Wide: Typical 5�06 lm: Typical 5�06 lm
• WT95-Tele: Typical 3926 lm: Typical 3926 lm
• WT94-Wide: Typical 5404 lm: Typical 5404 lm
• WT94-Tele: Typical 3812 lm: Typical 3812 lm
6 Throw ratio
• For CLM W6:
WT96 (Fixed Lens) ≈ 0.81
WT93 (Wide Zoom) ≈ 1.27-1.52
WT91 (Standard lens) ≈ 1.52-2.03
WT95 (Standard Zoom) ≈ 2.03-3.85
WT94 (Long Zoom) ≈ 3.85-7.32
• For CLM HD6:
WT96 (Fixed Lens) ≈ 0.77
WT93 (Wide Zoom) ≈ 1.2-1.45
WT91 (Standard lens) ≈ 1.45-1.94
WT95 (Standard Zoom) ≈ 1.94-3.67
WT94 (Long Zoom) ≈ 3.67-6.98
1-2 CLM W6_CLM HD6 Jan 31, 2012
Chapter 1 Introduction
No Item Description
� Projection lens
• Standard lens (WT91) ≈ 1.45-1.94 (WUXGA),
1.52-2.03 (WXGA), Zoom Ratio : 1.33X
• Fixed Lens (WT96) ≈ 0.77 (WUXGA), 0.81 (WXGA)
• Wide Zoom (WT93) ≈ 1.20-1.45 (WUXGA),
1.27-1.52 (WXGA), Zoom Ratio : 1.2X
• Standard Zoom (WT95) ≈ 2.0-3.80 (WUXGA),
2.03-3.85 (WXGA), Zoom Ratio : 1.9X
• Long Zoom (WT94) ≈ 3.67-6.98 (WUXGA),
3.85-7.32 (WXGA), Zoom Ratio : 1.9X
8 Lamp life • Total hours needed to decrease the lumens of the test
sample’s median lamp to 50% of original value:
1500 (Normal), 2000(ECO)
9Terminal
• Computer In x2, VESA (HD15) Blue, Female
• Monitor out x1, VESA (HD15) black, Female
• HDMI, version 1.3v x2
• CVBS In (Composite Video) RCA connector (Y), Female x1
• SVHS In (S-Video), 4-pin mini DIN, Female x1
• Provides S-Video input x1
• BNC RGBHV, BNC 75ohm Females x1 sets
• DC output. 3.5mm jack, Female x1,
Volts: 12v Amps: 250ma Max
• 9-pin RS232 male (d-sub) x1
• RJ45
10 Input single
• Hsync Frequency: 15 ~ 91.1 kHz
• Vsync Frequency: 43 ~ 85 Hz
• Video Signal RGB (PC)
Analog RGB: 0.7Vp-p, 75 ohm
Analog RGB: 1Vp-p, 75 ohm, Sync. Signal
Separate TTL H,V Sync.
Composite TTL Sync.
• Video
Composite video: 1Vp-p,�5 ohm
S-video Luminance: 0.714Vp-p,75 ohm
S-video Chrominance: 0.286Vp-p,75 ohm
1-3
CLM W6_CLM HD6 Jan 31, 2012
Chapter 1 Introduction
No Item Description
11 DMD chip
• DMD TYPE-A 1280x800 PIXEL 0.65” WXGA-800 2xLVDS
“TI” (for CLM W6)
• DMD TYPE-A 1080P 0.65” 2xLVDS (for CLM HD6)
12 Native resolution • 1280x800 WXGA (for CLM W6)
• 1920x1080 1080P (for CLM HD6)
13 Video compatibility
• Standards :
NTSC, NTSC4.43
PAL/PAL-M/PAL-N/SECAM
SDTV compatible (480i/p, 5�6i/p)
HDTV compatible (�20p, 1080i, 1080p)
14 Computer compatibility Apple® Macintosh®, iMac®, and VESA Standards:
WUXGA, UXGA, SXGA+, SXGA, WXGA, XGA, SVGA, VGA
15 Color Wheel
• Standard:
5-segment: R:80°/Y:30°/G:84°/W:90°/B:76°
• Optional:
6-segment: R:100°/C:23°/B:72°/G:90°/M:30°/Y:45°
16 Lamp • OSRAM 2xP-VIP 330W/1.0 E20.9 x2
1� System controller
• CLM HD6:
DUAL TI DDP 3021
• CLM W6
TI DDP 3020F
18 Cooling system
• - Advanced Air Flow
- Eleven fans with system acoustic noise level
- Temperature control circuits with adaptive fan rotational
speeds
- Maximum touch temperature meets UL60950-1
19 Temperature • Operating: 5°C -- 35°C
1-4 CLM W6_CLM HD6 Jan 31, 2012
Chapter 1 Introduction
1-2 System block diagram
Autres manuels pour CLM W6
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Barco Projecteur
Barco
Barco R9840420 Manuel utilisateur
Barco
Barco SLM R12 Manuel
Barco
Barco DP2K-15C Manuel utilisateur
Barco
Barco Galaxy 4K series Guide de l'utilisateur
Barco
Barco Galaxy WARP R9040320 Manuel utilisateur
Barco
Barco OV-815 Manuel utilisateur
Barco
Barco PJWU-101B Manuel utilisateur
Barco
Barco SLM R12 Plus Manuel utilisateur
Barco
Barco DICOM THEATER Guide de l'utilisateur
Barco
Barco G100 Manuel utilisateur
Barco
Barco R9001390 Manuel utilisateur
Barco
Barco R9002129 Manuel utilisateur
Barco
Barco BarcoReality 909 Split Pack R9040040 Manuel utilisateur
Barco
Barco ELM Series Manuel utilisateur
Barco
Barco R9002040 Manuel utilisateur
Barco
Barco R9841020 Cine VERSUM Master Manuel utilisateur
Barco
Barco DP2K-12C Manuel utilisateur
Barco
Barco iQ Pro R500 R9010221 Manuel utilisateur
Barco
Barco OV-1008 Manuel utilisateur
Barco
Barco PH series Manuel d'utilisation
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
