Barco iCon H250 Manuel utilisateur
iCon H250 / iCon H400
Installation manual
R9010510 / R9010500
R59770070/00
31/01/2007
Barco nv Presentations
Noordlaan 5, 8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.35.86.51
E-mail: [email protected]
Visit us at the web: www.barco.com
PrintedinBelgium
Table of contents
TABLE OF CONTENTS
1. Harddiskrecovery kit.............................................................................................3
1.1 Introduction ........................................................................................................................... 3
2. Harddiskrecoveryprocedure................................................................................... 5
2.1 iCon server boot configuration . . ..................................................................................................... 5
2.2 Defining commands .................................................................................................................. 6
2.3 The recovery.......................................................................................................................... 7
2.4 iCon H250 / H400 server setup .....................................................................................................10
Index......................................................................................................................13
R59770070 ICON H250 / ICON H400 31/01/2007 1
Table of contents
2R59770070 ICON H250 / ICON H400 31/01/2007
1. Hard disk recovery kit
1.HARDDISKRECOVERYKIT
Overview
• Introduction
1.1 Introduction
What can be done in case of hard disk failure?
There is a possibility to recover the hard disk of the iCon H250/H400 . This might eliminate the need to replace it in case of a hard
disk failure.
The recovery can be needed in case of non repairable virus infection, forgotten password, blue screen at start up...
In this procedure we will use the Linux operating system to do the recovery.
WARNING:This tool will remove all data from your hard disk!
Procedure
We first change the BIOS settings in order to make the projectors’ server boot from the USB DVD reader, using the image file of the
firmware.
Then we start the hard disk recovery. At the end of the procedure, we put the BIOS settings back to its original state.
Kit contents
The delivered kit includes the following items:
•R32998700: DVD-ROM containing the image file for your projector (hard disk data)
•R32998600: CD-ROM containing Linux recovery tool
Image 1-1
R59770070 ICON H250 / ICON H400 31/01/2007 3
1. Hard disk recovery kit
4R59770070 ICON H250 / ICON H400 31/01/2007
2. Hard disk recovery procedure
2. HARD DISK RECOVERY PROCEDURE
Overview
• iCon server boot configuration
• Defining commands
• The recovery
• iCon H250 / H400 server setup
2.1 iCon server boot configuration
Necessary tools
• DVD-ROM: Hard Disk Recovery Data iCon H250 / iCon H400
• CD-ROM: Hard Disk Recovery Data iCon H250 / iCon H400
• USB DVD reader device
• USB keyboard
•Windows
®XP product key
How to change the boot configuration?
1. Connect the USB DVD reader device and the USB keyboard to the server of you projector
Image 2-1
2. Power up your projector
3. When the server starts (on the first beep sound), press F2 to enter the BIOS
4. Navigate to the tab Boot
5. Use the +and the -keytomovetheUSB DVD-ROM to the top of the Boot priority list
Tip: Youmayhavetousethexkey to move it form the Excluded from boot order-list to the Boot priority order-list!
R59770070 ICON H250 / ICON H400 31/01/2007 5
2. Hard disk recovery procedure
Image 2-2 Image 2-3
6. Put the CD-ROM Hard Disk Recovery Data in the USB DVD reader device
7. Navigate to the tab Exit
8. Select Exit Saving Changes
Image 2-4
2.2 Defining commands
How to define the commands?
1. At the boot prompt, type the following text: fb1024 docache doeject
Image 2-5
Warning: You only have a limited amount of time to enter this command! If you exceed this time, type shutdown —r now
and restart the procedure!
Note: The keyboard layout at this moment is QWERTY
6R59770070 ICON H250 / ICON H400 31/01/2007
2. Hard disk recovery procedure
2. After about 5 seconds, the Load keymap (Enter for default) : prompt will appear: you have a limited amount of time to change
the keyboard configuration. For AZERTY you can enter the following figure: 2(= the figure corresponding to Belgian keyboard
configuration).
Image 2-6
3. A few seconds later, the USB DVD reader will eject the disc. You see this prompt: root@sysresccd/root%
Image 2-7
4. Remove the CD-ROM Hard Disk Recovery Data from the USB DVD reader
2.3 The recovery
How to do the hard disk recovery?
1. Insert the DVD-ROM Hard Disk Recovery Data in the USB DVD reader
2. At the prompt, enter the following text: mount —t iso9660 /dev/sr0 /mnt/cdrom
Tip: Pay attention to the spaces!
R59770070 ICON H250 / ICON H400 31/01/2007 7
2. Hard disk recovery procedure
Image 2-8
Note: You will see appear the following message: mount: block device /dev/sr0 is write-protected, mounting read-only
3. At the prompt, enter the following text: partimage
Image 2-9
4. Navigate to the item Image file to create/use using the tab key and enter the following text:/mnt/cdrom/iconh400.000
Image 2-10
Note: iconh400.000 is the name of the file with the firmware and data. It may differ depending on the version and the projector
type you are recovering!
5. Press tab
6. Use ↓and the space bar to select the item Restore partition from an image file
7. Press F5 , verify the partition description and use the space bar to close the window
8R59770070 ICON H250 / ICON H400 31/01/2007
Autres manuels pour iCon H250
3
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Barco Projecteur
Barco
Barco CNWU-61B Manuel utilisateur
Barco
Barco R9000972 Manuel utilisateur
Barco
Barco DP K-32B Series Manuel d'utilisation
Barco
Barco HDQ 4K35 Manuel d'utilisation
Barco
Barco Projector Manuel utilisateur
Barco
Barco PGXG-61B Manuel utilisateur
Barco
Barco RLM R6+ Performer Manuel utilisateur
Barco
Barco R9840700 Manuel utilisateur
Barco
Barco F400 Manuel utilisateur
Barco
Barco B-10 Mobile LED R9855510 Mode d’emploi
Barco
Barco R9002380 Manuel utilisateur
Barco
Barco R9001280 Manuel utilisateur
Barco
Barco VISION 3200LC Manuel utilisateur
Barco
Barco Galaxy NW12 Instructions d'installation
Barco
Barco R9040380 Manuel utilisateur
Barco
Barco R92112011 Manuel utilisateur
Barco
Barco Cineo12 Manuel utilisateur
Barco
Barco BarcoGraphics Maxwell/ 6300 Manuel utilisateur
Barco
Barco DP2K S-series Manuel utilisateur
Barco
Barco R9002411 Manuel utilisateur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
