Barco BarcoData 3300 Manuel utilisateur

INSTALLATION MANUAL

R9001450

DATA

3300 TCRPLUS

BARCO PROJECTION SYSTEMS

INSTALLATION MANUAL

Date :

121097 Art. No. :

R5975129

R9001450

DATA

3300 TCRPLUS

Federal communication commission (FCC statement)

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC ules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Instructions to the user :

if this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the

following measures :

- e-orientation of the receiving antenna for the radio or television.

- elocate the equipment with respect to the receiver.

- Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.

- Fasten cables connectors to the equipment by mounting screws.

Note :

The use of shielded cables is required to comply within the limits of Part15 of FCC rules and EN55022

BARCO nv/Projection Systems

Noordlaan 5

B-8520 Kuurne

Belgium

Tel : +32/56/368211

Fax : +32/56/351651

E-mail : [email protected]

Visite Barco at the web : http://www.barco.com

Printed in Belgium

Due to constant research, the information in this manual is subject to change without notice.

Produced by BARCO NV, October 1998.

Trademarks are the rights of their respective owners.

Table of Contents

i-1

5975129 BA CODATA 3300 TC PLUS 121098

iTABLE OF CONTENTS

TABLE OF CONTENTS .............................................................................................................................................................................. i-1

INSTALLATION MODE ............................................................................................................................................................................. 1-1

Starting up the Installation Mode ................................................................................................................................................... 1-1

Configuration ................................................................................................................................................................................. 1-1

Internal Patterns ............................................................................................................................................................................ 1-1

How to use the built-in adjustable lensholder .............................................................................................................................. 1-2

HA DWA E SET UP ................................................................................................................................................................................ 2-1

How to activate the password function ...................................................................................................................................... 2-1

2-1

Installation Mode

5975129 BARCODATA 3300 TCRPLUS 121098

1INSTALLATION MODE

Starting up the Installation Mode

Push the control disc up or down to highlight Installation and then

press ENTER.

ADJUSTMENTMODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

INSTALLATION

INPUT SLOTS

CONVERGENCE

CONFIGURATION

OSD COLOR

INTERNALPATTERNS

NO SIGNAL [BLACK]

Select with or

then <ENTER>

<EXIT> to return.

ENTER continues to the Installation mode selection menu.

EXIT returns to operational mode.

The following item can be selected in the Installation mode :

Input slots : to set up the input for a specific source. See

'Connections' for the different source types.

Convergence : to adjust the convergence of the LCD panels. For

more information contact an authorised BA CO service technician.

Configuration : to set up the projector position.

OSD color : to change the color of the highlighted item.

Internal Patterns :

- outline

- color bars

- multiburst

- checker board

- purity

- Page Char

- Alpha-numeric Char

- gray bars

No signal : to display a black or blue screen when no source is

connected to the projector.

Only the items used during the physical installation will be explained

hereafter. The other items are explained in the owners manual.

Select with or

then <ENTER>

<EXIT> to return.

INTERNALPATTERNS

OUTLINE

COLOR BARS

MULTIBURST

CHECKER BOARD

PURITY

PAGE CHAR

ALPHA-NUMERICCHAR

GRAY BARS

Select with or

then <ENTER>

<EXIT> to return.

Configuration

Highlight "Configuration" by pushing the control disc up or down and

press ENTER to select.

For more information, see Projector configuration in chapter Installa-

tion Set Up.

Internal Patterns

Theprojectorisequippedwithdifferentinternalpatternswhichcanbe

used for measurment purposes.

Highlight "Internal Patterns" by pushing the control disc up or down

and press ENTER to display the Internal Pattern selection menu.

The following test pattern are available :

- Outline

- Color Bars

- Multiburst

- Checker Board

- Purity

- Page Char

- Alpha-numeric Char

- Gray bars

Each pattern (except Purity) can be inverted by pressing ENTER.

To return to the normal pattern, press EXIT.

INSTALLATION

INPUT SLOTS

CONVERGENCE

CONFIGURATION

OSD COLOR

INTERNALPATTERNS

NO SIGNAL [BLACK]

INSTALLATION

INPUT SLOTS

CONVERGENCE

CONFIGURATION

OSD COLOR

INTERNALPATTERNS

NO SIGNAL [BLACK]

2-2

Installation Mode

5975129 BARCODATA 3300 TCRPLUS 121098













33 MM

Convergence adjustment of the LCD panels.

Every LCD panel has 6 adjustment screws. By turning these screws

you change the relative position of the panels and converge the

image.

Always start with the adjustment of the green panel. When the green

image is correctly focused, it will later on be used as the reference

image to converge the red and blue image.

Next alignments have to be done :

You have to adjust the green panel until the indicated lines on the

screen are focused (sharp lines). Continue with the blue panel and

adjust until the blue lines coincide with the green lines. Than continue

with the red panel until the red lines coincide with the green lines.

Follow the next procedure to adjust the LCD panels.

* Open the top cover as described in Gaining access to the DIP

switches under Connecting to a computer in chapter Connections.

The three mounting parts for the LCD's (two are shown on the drawing

below) are located on the black metal cover. The screws are

indicated from 1 to 6 for each color.

To adjust the convergence, there are test patterns provided in the

service menu.

Push the control stick forward or backward to hightlight Convergence

and press ENTER to display the Convergence menu.

Start with the Green test pattern and continue with the Blue on green

and finish with the ed on green.

INSTALLATION

INPUT SLOTS

CONVERGENCE

CONFIGURATION

OSD COLOR

INTERNALPATTERNS

NO SIGNAL [BLACK]

The pattern shows lines of one pixel.

Near six lines on the displayed pattern, a screw is drawn with a

number next to it (e.g. if displayed in green = corresponding with the

screws and numbers on the green LCD panel).

When turning a screw in the direction marked by the arrow above the

displayed screw on the screen, the line on the screen moves in the

direction of the straight arrow.

Select with or

then <ENTER>

<EXIT> to return.

CONVERGENCE

GREEN

BLUE ON GREEN

RED ON GREEN

HATCH

2-3

Installation Mode

5975129 BARCODATA 3300 TCRPLUS 121098

























Green focusing

a. Insure all convergence screws are adjusted to a length of about 33

mm (1.3") between the two plates.

b. Adjust the projection lens until optimal focus for point 1 is obtained.

c. Turn screw 2 for optimal focus of the corresponding green line 2

on the screen.

d. This alignment influences the other, so repeat if necessary steps

b. and c. until points 1 and 2 are focused.

e. Turn screw 3 for optimal focus of the corresponding green line 3 on

the screen.

f. epeat if necessary the steps b. to e. until the complet screen is

focused.

g. Secure the projection lens by turning the fastener ring clockwise.

Green position

a. If necessary turn screw 5 until the two horizontal lines 5 on the

screen are on one horizontal line.

When the green pattern is correctly focused, press EXIT to return to

the Test pattern menu.

Blue on green convergence.

Push the control disc up or down to hightlight Blue on green and press

ENTER to display the Blue on green test pattern.

The longest lines are the blue lines. These lines must be converged

with the green lines.

The drawn screws and numbers are displayed in blue.

Follow next steps :

Blue focusing

a. Insure all convergence screws are adjusted to a length of about 33

mm (1.3") between the two plates.

b. Turn screw 1 for optimal focus of the corresponding point 1 on the

screen.

c. Turn screw 2 for optimal focus of the corresponding point 2 on the

screen.

d. Due to interaction, it may be necessary to repeat step b. and c. until

point 1 and 2 are focused.

e. Turn screw 3 for optimal focus of the corresponding point 3 on the

screen.

f. Due to interaction, it may be necessary to repeat steps b. to d. until

point 1, 2 and 3 are correctly focused.

Select with or

then <ENTER>

<EXIT> to return.

CONVERGENCE

GREEN

BLUE ON GREEN

RED ON GREEN

HATCH

Blue position

g. Turn screw 4 until the red horizontal line coincide with the green

horizontal line in point 4 on the screen.

h. Turn screw 5 until both horizontal lines marked with 5 are on one

horizontal line.

i. epeat step g. and h. until the horizontal lines are converged.

j. Adjust screw 6 for optimal convergence of the vertical lines.

k. epeat step i. and j. until a optimal convergence in horizontal and

vertical direction is obtained.

2-4

Installation Mode

5975129 BARCODATA 3300 TCRPLUS 121098

l. Due to interaction, turning on screw 4, 5 and 6 can influence the

focus of the image. If necessary, repeat procedure from step b. .

Red on green convergence.

Push the control disc up or down to highlight Red on green and press

ENTER to display the ed on green test pattern.

epeat the same procedure as for Blue on green lines but read red

when blue is indicated.

To check the result of the convergence adjustments, highlight Hatch

and press ENTER. A hatch pattern will be displayed on the screen.

ENTER : displays a hatch pattern.

EXIT : returns to the service menu.

All lines must be displayed in white, if not so repeat the convergence

adjustment procedure.

How to use the built in adjustable lensholder.

With the lensholder, it is possible to shift the displayed image up or

down on the screen without moving the projector from its normal

positioin and without any geometric picture distortion. This built-in

featureisparticularly usefulforuse indualprojector configurationsor

for applications when the projector cannot be installed in its standard

position.

Features :

- Vertical and horizontal shift of the lens without removing the top

cover,

5 mm left and 5 mm right

15 mm up and 15 mm down.

- Makes it possible to project a geometric non-distored image from a

non-standard position.

-The shiftofthelensholderisnotdeterminedbythelensbutdepends

on the screen width.

- Can be used with all available lenses.

Lens shift up/down

Lens shift left/right

Select with or

then <ENTER>

<EXIT> to return.

CONVERGENCE

GREEN

BLUE ON GREEN

RED ON GREEN

HATCH

Select with or

then <ENTER>

<EXIT> to return.

CONVERGENCE

GREEN

BLUE ON GREEN

RED ON GREEN

HATCH

2-5

Installation Mode

5975129 BARCODATA 3300 TCRPLUS 121098

-0,5

-0,25

0,25

0,5

123456

80 120 160 200 240

40 30

-1,5

-1

-0,5

0,5

1,5

123456

80 120 160 200 240

40 90

Screen Width

Horizontal Screen Shift

-15

-30

Maximum 5 mm right lens shift

Maximum 5 mm left lens shift

-30

-60

-90

Screen Width

Vertical Screen Shift

Maximum 15 mm downwards lens shift

Maximum 15 mm upwards lens shift

no shift

5 mm

10 mm

-5 mm

-10 mm

2.5 mm

no shift

-2.5 mm

How to shift the image :

- First shift the image left or right until the correct horizontal position

isobtained. Turnclockwisetoshifttheimagetotheright,turncounter

clockwise to shift to the left. Use the hand screw.

- Shift the image up or down until the correct vertical position of the

image is obtained. Turn clockwise to shift the image up, turn counter

clockwise to shift down. Use the hand screw.

Midposition of the adjustable lensholder.

-Ifthetop coverisopened, thelensholderindication linehasto match

with the center of the hole in the plate behind the lensholder.

-Ifthe top coverisclosed, the3indicationlines onthelensholder has

to match with indication on the top cover.

hole

indication

line

Horizontal shift is function of the Screen Width for

various lens shifts.

Vertical shift is function of the Screen Width for various lens shifts.

Both the vertical and horizontal shift of the displayed picture can be

calculated as follows :

Screen shift = lens shift x 1 + (Screen width / LCD panel width)

LCD panel width for 3200 series : 0,06480 m (2.551 inch)

2-1

Hardware Set Up

5975119 BA CODATA 3300 121098

How to activate the password function?

Off

HARDWARE SET UP

The password function can be hardware set with a DIP switch on

the CPU module. To change the position of this DIP switch, it is

necessary to open first the top cover.

Gaining access to the DIP switch

Power down the projector and unplug the power cord from the wall

outlet.

Turn both lock screws with a screwdriver or coin counter

clockwise.

Lift up and pivot the top cover. Attention : the cover is not secured

with an incorporated support. When opening, turn it over slowly.

The processor module with the DIP switches is located on the front

side. Loosen the locking

screws.

Open the top cover

When DIP switch 1 is in the :

- ON position, password is activated.

-OFF position, password not activated, service mode

is free accessible.

Table des matières

Autres manuels Barco Projecteur

Barco

Barco DP2K-11CX Manuel du propriétaire

Barco

Barco MSWU-81E Manuel utilisateur

Barco

Barco Galaxy NH-12 Manuel utilisateur

Barco

Barco FLM R20+ Performer Manuel utilisateur

Barco

Barco LX-5 SERIES Manuel utilisateur

Barco

Barco FS40 - 4K Guide de l'utilisateur

Barco

Barco RETRO GRAPHICS 2100LC R9001319 Manuel utilisateur

Barco

Barco R9004460 Manuel utilisateur

Barco

Barco R9003110 Manuel utilisateur

Barco

Barco G50 Manuel utilisateur

Barco

Barco R9002030 Manuel utilisateur

Barco

Barco DP2K-S Series Manuel d'utilisation

Barco

Barco F22 Series Manuel utilisateur

Barco

Barco DATA 808s SP Manuel utilisateur

Barco

Barco XLM HD30 Manuel utilisateur

Barco

Barco BarcoGraphics Maxwell/ 6300 Manuel utilisateur

Barco

Barco UDX Series Manuel utilisateur

Barco

Barco CineVersum 120 Manuel utilisateur

Barco

Barco DP2K-12C Manuel utilisateur

Barco

Barco F80 series Manuel utilisateur

Barco

Barco XLM H25 Manuel utilisateur

Barco

Barco R9002410 Manuel utilisateur

Barco

Barco G50 Manuel utilisateur

Barco

Barco R9001250 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur