Banner Q45 Manuel utilisateur

Printed in USA May 2012 P/N 159359 rev. A

Step 1: Wire the Gateway’s Outputs

To wire the Gateway’s outputs:

1. Remove the four screws holding the radio cover to the housing base.

2. Wire your outputs according to your network’s configuration.

For additional configuration and Gateway wiring options, refer to the Gateway with Switch Mapping datasheet, part number 161862. To

use more than six sensors (up to 47) in the wireless network, use a Modbus host system (see the Host Configuration manual, Banner p/n

134112).

Each wireless network may have up to six Wireless Q45 Sensor optical models (default configuration) when using the DX80G2M6S-Q

Gateway’s DIP switch-based mapping.

Each Wireless Q45 Sensor is mapped to one of the Gateway’s six discrete outputs.

Gateway Model

DX80G2M6-QC

Q45 1

Q45 2

Q45 3

Quick Start Guide for Wireless Q45 Sensor Networks

Formed Using the -QC Gateway

Each sensor is mapped to the one of the Gateway’s outputs by

default. Other mapping options are also supported.

Q45 4

Q45 5

Q45 6

Gateway

outputs 1-6

Use this wiring diagram for the default configuration for Optical Sensor Models: six Q45 Sensors mapped to the six Gateway outputs.

DI1

DI2

DI3

DI4

DI5

DI6

V-

V+

DO6

DO5

DO1

DO2

DO3

DO4

Tx/+

Rx/-

Q45 6

Q45 1

Q45 5

Q45 4

Q45 3

Q45 2

Load

To GND

Banner Engineering Corp. • Minneapolis, MN U.S.A

www.bannerengineering.com • Tel: 763.544.3164

2P/N 159359 rev. A

Quick Start Guide for Q45 Networks

Step 4: Verify Radio Communication

To verify the Gateway and Wireless Q45 Sensor are communicating:

•Gateway's LED 1 is solid green.

•Until communication is established with the Gateway, the Q45's red LED flashes.

•After communication is established, the Q45's green LED flashes.

Step 5: Test the Wireless Q45 Sensor Operation

Mount the Wireless Q45 Sensor in your application and view the yellow

LED, which indicates the sensor’s output.

After 15 minutes of inactivity, the LED turns off to conserve power. To

activate the LED, push the button once.

For alignment instructions, refer to the Wireless Q45 Sensor’s datasheet.

Step 3: Bind the Wireless Q45 Sensors to the Gateway

Binding Wireless Q45 Sensors to their Gateway ensures the Q45s only exchange data with the Gateway they are bound

to. To create your network, bind the Wireless Q45 Sensors to the Gateway and assign them a unique Node address.

1. On the Gateway, triple-click button 2. Both LEDs flash red.

2. On the Gateway, use both rotary dials to assign the Node address for the Q45. Use the left dial for the left digit

and the right dial for the right digit. For example, to assign your Q45 to Node 01, set the left dial to 0 and the

right dial to 1. The Gateway’s LCD displays BINDING and NOD 1. (When using the default Gateway DIP switch

positions, only Nodes 01, 02, and 03 will be mapped to the Gateway’s outputs.)

3. On the Wireless Q45 Sensor, triple-click the button. While in binding mode, the red and green LEDs flash

alternately. After the Q45 is bound, the LEDs flash together four times. The Q45 automatically exits binding

mode.

4. Label the sensor with the Q45’s Node address.

5. Repeat steps 2 through 4 for as many Wireless Q45 Sensors as are needed for your network.

6. On the Gateway, single-click button 2 to exit binding mode.

Step 2: Apply Power

Wire Color Gateway

V+ Brown +10 to 30V dc Input

V−Blue dc common (GND)

Connecting dc power to the communication pins will

cause permanent damage.

Apply Power to the Gateway Turn on the Wireless Q45 Sensor

To conserve battery power, the Wireless Q45 Sensor ships from the

factory in storage mode. To wake the Q45:

1. Loosen the clamp plate on the top of the Wireless Q45

Sensor and lift the cover.

2. Press and hold the

button for five seconds.

When the Q45 is on, the

red LED flashes. Button

Button

Yellow LED indicates sensor

function

Green and red LEDs indicate radio

functions

Button 2

Rotary dials

Autres manuels pour Q45

Table des matières

Autres manuels Banner Porte

Banner

Banner DX80G9M6S-P2 Manuel utilisateur

Banner

Banner SureCross DX80 Manuel utilisateur

Banner

Banner Sure Cross DX80 Series Manuel utilisateur

Banner

Banner SureCross DX99 Mode d’emploi

Banner

Banner SureCross DX70 Series Manuel utilisateur

Banner

Banner SureCross DX80 Manuel utilisateur

Banner

Banner SureCross DX80 Manuel utilisateur

Banner

Banner Sure Cross P2-KR Manuel utilisateur

Banner

Banner DX80N2X6S-PB2 Manuel utilisateur

Banner

Banner SureCross DX80 Manuel utilisateur

Banner

Banner Sure Cross DX80 Manuel utilisateur

Banner

Banner SureCross DX80 Manuel utilisateur

Banner

Banner SureCross DX80 Instructions d'installation et d'entretien

Banner

Banner Sure Cross Performance GatewayPro DX80P*A6... Manuel utilisateur

Banner

Banner DXMR90-4K Manuel utilisateur

Banner

Banner Sure Cross DX80 Manuel utilisateur

Banner

Banner AMG Manuel utilisateur

Banner

Banner SureCross Performance GatewayPro Series Manuel utilisateur

Banner

Banner SureCross DX80 Manuel utilisateur

Banner

Banner SureCross DX80 Manuel utilisateur

Banner

Banner SureCross DX80 Manuel utilisateur

Banner

Banner SureCross Performance FlexPower DX80G9M2S-P7 Manuel utilisateur

Banner

Banner SureCross Performance FlexPower DX80G9M2S-P7 Manuel utilisateur

Banner

Banner SureCross DX80 Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur