AWS CP2-100 Manuel utilisateur

American Weigh Scales

CP2-100 (100x0.01g)

CP2-600 (600x0.1g)

User Manual

CP2-Series

CP2-Series Manual

Thank you for purchasing the American Weigh

CP2-Series digital pocket scale. Please read all operating

instructions carefully before use. Scales are precision

measuring devices and should always be handled with

proper care. To ensure years of reliable service, keep these

simple tips in mind:

• Do not exceed the scale’s maximum capacity.

Overloading your scale can permanently damage it!

• Avoid exposure to extreme heat or cold. Scales

perform best at normal room temperature. If

temperatures have changed dramatically, calibration

and adjustment may be necessary.

• Allow your scale to warm up for 30-60 seconds before

performing calibration and adjustment(if available).

• Store your scale in a clean, dry location. Dust, dirt,

and moisture can accumulate on the weighing

sensors and electronics causing inaccuracy or

malfunction.

• Avoid using your scale in close proximity to strong

radio wave emitting devices such as computers, cash

registers, and cordless phones.

• Alwaysweighonaatandlevelsurface,freefrom

vibrations and drafts. The corner of a room is usually

the most stable.

• Gently apply all items to be weighed. Do not drop

items onto the weighing platform.

• Avoid dropping your scale. The warranty does not

cover damage due to rough treatment or overload.

• Checkthebatteriesrstifyouarehavinganytrouble

with your scale. This simple step can remedy most

scale issues.

• Do not disassemble your scale. This product contains

no user serviceable parts.

I. Part List

1. Scale

2. Cover/Expansion Tray

3. CR2032 Lithium Batteries (x2)

II. Key Description

III. Battery Installation

1. Beforeusingthescaleforthersttime,check

the battery compartment and remove any plastic

insulation strips or packaging that may be in place to

prevent battery drainage during shipping/storage.

2. If you are replacing the batteries, make sure the

positive and negative contacts are properly aligned.

ON/OFF

Key

Mode/Tare

Key

Install Negative

Side Up

Install Positive

Side Up

Negative Terminal

Positive Terminal

CR2032 (Button Cell) Battery Installation

Install Negative

Side Up

Install Positive

Side Up

Negative Terminal

Positive Terminal

CR2032 (Button Cell) Battery Installation

CP2-Series Manual

IV. Operation

1. Placethescaleonaat,levelsurfaceandpressthe

key to turn the scale on.

2. Once the start-up process completes and the scale

goes to zero you are ready to weigh.

3. Place the quantity to be weighed onto the weighing

platform.

4. Wait a couple seconds for the display to stabilize

before taking a weight reading.

V. Changing the Unit of Measure

1. Press and hold the Mkey to change the scale’s

displayed unit of measure.

2. If the scale is turned off, then back on, it will default

to the last unit used.

• CP2-Series Units: g (gram) oz (ounce) ozt (troy

ounce) dwt (pennyweight) ct (carat) gn (grain)

VI. Using the Tare Feature

You can use this scale’s tare feature to subtract the weight

of an empty container or vessel for net weight determination.

NOTE: The weight of the container will subtract from the

available capacity.

1. Place the empty container or vessel on the weighing

platform.

2. Press the Mkeybriey.Thedisplaywillthenresetto

zero. If the container is removed, it’s weight will be

displayed as a negative number.

3. Youmaynowllthecontainerwiththequantityto

be weighed. The display will show the net weight of

the contents.

4. To return to normal weight display (gross weight),

remove any items from the weighing platform and

press the M key again to re-zero the scale.

VII. Calibration

Calibration and adjustment are performed at the factory.

However, the weighing range can shift slightly during

shipping. Also, due to changes in local acceleration of gravity

around the world, adjustment is recommended when moving

the scale from one location to another. To check calibration:

1. Place the required calibration weight on the scale

and note the displayed value.

2. If the displayed value is not within acceptable

tolerance (see chart below), adjustment is required.

Model Acceptable

Tolerance (±)

Calibration

Weight

Recommended

Accuracy Class

CP2-100 0.02g 100g OIML M2

CP2-600 0.2g 500g OIML M2

VIII. Adjustment

1. While the scale is turned OFF, press and hold the

Mkey.

2. While continuing to hold the Mkey, tap the key to

turn the scale ON.

3. The display will show the internal statement number.

4. Press the key again. The display will show “Zero”

followed by the required calibration weight.

5. Place the required calibration weight on the center of

the scale platform and press the key again.

6. Thedisplaywillshow“F”fornished.Youmay

remove the calibration weight and turn off the scale.

CP2-Series Manual

IX. Troubleshooting

• Problem: Scale will not turn on

• Solution: Check the batteries

• Problem: Displayedweightuctuatesrandomly

• Solution: Make sure your workspace is stable and

free of any air currents or vibration

• Problem: Displayed weight is inaccurate

• Solution: Perform a calibration adjustment

X. Error Codes

1. OUTZ - Zero range has shifted. Perform calibration

adjustment. If the problem persists, the load cell may

be permanently damaged due to overloading.

2. O_Ld - Maximum capacity exceeded. Remove the

extra weight to avoid damaging the load cell.

3. Lo - Batteries are low. Replace the batteries.

4. UnST - The scale is unstable. Use the scale in a

more stable position.

CP2-100 CP2-600

Max. Capacity 100g 600g

Readability 0.01g 0.1g

Min. Capacity 0.03g 0.2g

Power 2 x CR2032 Lithium

Dimensions 3.8 x 2.1 x 0.6 in.

Platform Dimensions 1.8 x 2.5 in.

Warranty 10 Year Limited Warranty

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AWS Échelle

Manuels Échelle populaires d'autres marques

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur

Fidelity Electronics

Fidelity Electronics G2e Manuel utilisateur