Avdel G3LB Tool Manuel utilisateur
G3LB Tool –Instruction Manual Supplement.
This must accompany the Manual (07900-00930) for the STD
Genesis® nG3 tool
G3LB Tool
Hydro-Pneumatic Power Tool
Original Instructions
2
Intent of Use
The Genesis® nG tool must “Only” be used for placing 3/16” & 1/4” NeoBolt® as outlined in “Tool setting guide – Small diameter NeoBolt®:
(07900-01071 GB)
Tool Specification
Air Pressure
Minimum - Maximum
5-7 bar
Free Air Volume Required
@ 5.5 bar
4.3 litres
Stroke
Minimum - Maximum
10-29 mm
Pull Force
@ 5.5 bar
12.9 kN
Cycle Time
Approximately
0.8 seconds
Noise Level
Less than
75 dB(A)
Weight
Without nose equipment
2.3 kg
Vibration
Less than
2.5 m/s2
Safety Instructions
For the full safety instructions refer to the associated Genesis® nG tool manual (07900-00930 GB)
Certificate of Conformity
Refer to the associated Genesis® nG Instruction Manual (07900-00930 GB)
3
General Assembly
Base Tool –71256-02000
Parts List
G3LB NEOBOLT PLACING TOOL VARIANT PARTS LIST
ITEM
PART NUMBER
DESCRIPTION
QTY
ITEM
PART NUMBER
DESCRIPTION
QTY
1
71256-02001
BODY MACHINED
1
7
71256-02006
LOCK NUT
1
2
71256-02002
PISTON STOP
1
8
71256-02005
ADJUSTING NUT
1
3
71256-02003
SPRING HOUSING
1
9
07002-00098
NYLOC NUT
1
4
71256-02004
HYDRAULIC PISTON
1
10
71256-02007
ADJUSTING STOP
1
5
07002-00202
WASHER
1
11
71256-02002
PISTON STOP
1
6
07007-02136
SPRING
1
12
07003-00472
O-RING
1
*NEW PARTS IN nG3 LIST
6
3
2
5
1
4
7
8
9
11
10
0
12
4
Stroke Information
The diagrams below show the minimum and maximum stroke conditions when rotating the adjusting nut 8. When the adjusting nut is unscrewed beyond
the maximum allowable stroke, air will start to leak from the rear of the adjusting nut. Do not use the tool if the air leaks from the tool. When air leaks
from the tool, isolate the air from the tool and then screw the adjusting nut back onto the spring housing 3. The adjusting nut will not have any air
pressure behind it should the end user carry on unscrewing the nut from the spring housing. When setting the stroke of the hydraulic piston 4, it is highly
recommended that the locking nut 7 is tightened into the adjusting nut 8.
5
Maintenance/Dismantling Instructions
THE AIR LINE MUST BE DISCCONNECTED BEFORE ANY DISMANTLING IS ATTEMPTED
1. Unscrew the Adjusting Nut 8from the Spring Housing 3by hand.
2. Unscrew the Spring Housing fully 3using a 25mmA/F spanner. Remove the Spring 6, Washer 5and Hydraulic Piston 4from the rear of the
tool.
3. To remove the Piston stop 2the Base Cover 31 must first be removed to gain access
4. Clamp the body of the inverted tool ACROSS THE AIR INLET BOSSES in a vice fitted with soft jaws.
5. Pull off Rubber Boot 48.
6. Using the peg spanner* unscrew Base Cover 31.
7. Unscrew Nyloc Nuts 67 (2 off) and remove Base Plate Assembly 65.
8. Remove Cylinder Liner 37 together with Sealing Washers 29 (2 off) and ‘O’ Rings 66 (2 off).
1. Remove Pneumatic Piston Assembly 57 together with ‘O’ Ring 75, Lip Seal 90 (3 off), Guide Ring 51 and Piston Stop 2.
Re-assemble in the reverse order.
For Safety and Full Servicing and Maintenance instructions, refer to the nG3 Genesis® tool Manual (07900-00930 GB).
Item numbers in bold refer to the parts list on page 2 in this flyer and page 24 in the nG3 tool manual
6
Manual Number
Issue
C/N
07900-01067
D
16/303
Avdel UK Limited
Stanley House, Works Road
Letchworth Garden City, Hertfordshire SG6 1JY
Tel. +44 1582 900-000 –Fax -001
© 2016 Stanley Black & Decker, Inc.
Avdel®, Genesis®and NeoBolt®, are registered trademarks of Avdel UK Limited.
AV™ is a trademark of Avdel UK Limited.
The names and logos of other companies mentioned herein may be trademarks of their respective
owners.
This document is for informational purposes only. Avdel UK Limited makes no warranties, expressed
or implied, in this document.
Data shown is subject to change without prior notice as a result of continuous product development
and improvement policy.
Your local STANLEY Engineered Fastening representative is at your disposal should you need to
confirm latest information.
Table des matières
Autres manuels Avdel Outils électriques
Avdel
Avdel 7265 Manuel utilisateur
Avdel
Avdel Genesis G3 Manuel utilisateur
Avdel
Avdel 0749 MkII type Manuel utilisateur
Avdel
Avdel 7552 Manuel utilisateur
Avdel
Avdel Genesis G2LB Manuel utilisateur
Avdel
Avdel 73200 Tool Manuel utilisateur
Avdel
Avdel 74405 Manuel utilisateur
Avdel
Avdel 74200 Manuel utilisateur
Avdel
Avdel Avbolt 07220 Manuel utilisateur
Avdel
Avdel 71404 Manuel utilisateur
Avdel
Avdel 7536 Instructions de fonctionnement
Avdel
Avdel 7265 Manuel utilisateur
Avdel
Avdel Genesis 7537 Manuel utilisateur
Avdel
Avdel Genesis G1 71204 Manuel utilisateur
Avdel
Avdel 74401 Manuel utilisateur
Avdel
Avdel 07572 Manuel utilisateur
Avdel
Avdel 71234 Manuel utilisateur
Avdel
Avdel Genesis G2HD Manuel utilisateur
Avdel
Avdel 74200 Manuel utilisateur
Avdel
Avdel 753 MkII Manuel utilisateur
