Avaya IG550 Manuel utilisateur

03-601553 Issue 1 February 2007 1

700431984

03-601553

Issue 1

February 2007

Quick Start for Hardware Installation: IG550 Integrated

Gateway

Preparing before you go on-site

1. Check Juniper software compatibility with TGM550 Gateway Module firmware. See http://

support.avaya.com.

2. Download the most recent firmware for the TM550. See http://support.avaya.com.

3. Ensure the customer has an FTP or TFTP server that is accessible to the TGM550. If not,

download a TFTP server to your laptop.

4. Review safety requirements and airflow requirements. See Installing and Configuring the IG550

Integrated Gateway.

5. Get the tools you need:

●Electrostatic discharge (ESD) grounding strap

●Flathead and Phillips head screwdrivers

Getting ready on-site

1. Verify you have:

●The Juniper Services Router (J4350 or J6350).

●A 10 AWG grounding cable

●An AC or 14 AWG DC power cable

●Cables for the TGM550, Telephony Interface Modules (TIMs), and Physical Interface Modules

(PIMs).

!CAUTION:

CAUTION: You cannot use a 14 AWG grounding cable with the router. The grounding cable must be

10 AWG.

●A USB modem

●Two distinct and different console cables:

- An RJ-45 console cable and DB-9 adapter for console connections to the TGM550.

- An RJ-45 rollover cable and DB-9 adapter for console connections to the Juniper router.

2 Quick Start for Hardware Installation: IG550 Integrated Gateway

Installing hardware

1. If the customer has a four-post rack and is using a shelf, install the shelf according to manufacturer

guidelines. If the customer is using the brackets supplied with the router, install the brackets on the

chassis of the Juniper Services router midway between the front and back.

2. Install the router on the rack.

3. Be sure the power to the router is off.

Gateway

ALM

ACT

TGM550 Console

ASB

ETR

RST

Line

Trunk

1234

Analog

ALM

ACT

TIM514 Line5678

Line1234

E1/T1

ALM

ACT

TIM510

TST

SIG

SO EI SM EMSI EO

BRI

ALM

ACT

TIM521 4

CONSOLE AUX USB

J4350

POWER

POWER RESET

CONFIG

STATUS

ALARM

10/100/1000

0/00/10/20/3

LINKTX/RX

LINKTX/RXLINKTX/RX

TX/RXLINK

Juniper

NETWORKS

qsmabrkt LAO 092906

Gateway

ALM

ACT

TGM550Console

ASB

ETR

RST

Line

Trunk

1234

Analog

ALM

ACT

TIM514Line

5678

Line

1234

E1/T1

ALM

ACT

TIM510

TST

SIG

SOEISMEMSIEO

BRI

ALM

ACT

TIM5214

CONSOLEAUXUSB

J4350

POWER

POWERRESET

CONFIG

STATUS

ALARM

10/100/1000

0/00/10/20/3

LINKTX/RX

LINKTX/RXLINKTX/RX

TX/RXLINK

Juniper

NETWORKS

qsmarack LAO 092906

Quick Start for Hardware Installation: IG550 Integrated Gateway

03-601553 Issue 1 February 2007 3

!CAUTION:

CAUTION: The Juniper Services Router must be turned off before inserting or removing the Avaya

TGM550, TIM modules, or PIM modules. These modules are not hot-swappable. If you

attempt to remove or insert these modules while the router is turned on, the router might

reset or malfunction in some other way.

4. Insert the TGM550 and each TIM or PIM into the correct slot.

5. Align the notches in the connector at the rear of the TGM550, TIM, or PIM with the notches in the

slot in the router. Then slide the module in until it lodges firmly in the router.

!CAUTION:

CAUTION: Carefully slide the module straight into the slot to avoid damaging the connector

components.

6. Cable the TIMs and PIMs.

●TGM550 — CAT5 harness cables with RJ11 connectors

●TIM510 T1/E1 — H600-383 Group 2 T1 cable with an RJ48C connector

●TIM514 — CAT5 cable with an RJ11 connector

●TIM521 — CAT5 cable with an RJ45 connector

●Juniper PIMs — see Juniper J4350 and J6350 Services Router Getting Started Guide, Release

8.2.

7. Connect the grounding cable to earth ground and the chassis grounding point.

Specifications:

●10 AWG

●Minimum 8 Amps amperage

h LAO 1003063macrdr

Analog

ALM

ACT

TIM514 Line5678

Line1234

E1/T1

ALM

ACT

TIM510

TST

SIG

SO EI SM EM SI EO

BRI

ALM

ACT

TIM521 4

CONSOLE AUX USB

J4350

POWER

POWER RESET

CONFIG

STATUS

ALARM

10/100/1000

0/0 0/1 0/2 0/3

LINK TX/RXLINK TX/RX LINK TX/RX

TX/RX LINK

Juniper

NETWORKS

Gateway

ALM

ACT

TGM550 Console

ASB

ETR

RST

LineTrunk

1234

Line

4 Quick Start for Hardware Installation: IG550 Integrated Gateway

●Ring-type, vinyl-insulated TV14-6R lug or equivalent to accommodate the 10 AWG cable.

8. Connect power to the back of the router.

AC Power

●Insert the appliance coupler end of a power cord into the appliance inlet on the power supply

faceplate.

●For a 6350 only, repeat for the second power supply.

●Insert the plug of each cord into an AC power source receptacle.

DC Power

●Ensure that the voltage across the DC power source cable leads is 0 V and that there is no

chance that the cable leads might become active during installation.

●Verify that a licensed electrician has attached the appropriate power cable lugs to the ends of the

negative and positive DC source power cables. These are the lugs that you are attaching to the

chassis DC terminals.

qsmagnd3 LAO 092906

qsmagnd2 LAO 092906

J4350 J6350

Quick Start for Hardware Installation: IG550 Integrated Gateway

03-601553 Issue 1 February 2007 5

Loading Disk on Key, if available

1. If available, insert the Disk on Key (USB memory stick) into the USB port on the front of the router.

The Disk on Key contains the configuration information. If a Disk on Key is not provided, go to

Configuring the router using the CLI, if Disk on Key not available on page 7.

2. Press the power button to turn on the Juniper Services Router.

3. When the Power on LED lights steady green, remove the Disk on Key. The configuration file has

been downloaded, loaded, and committed. The root password is also set as part of the

configuration.

qsmausbk LAO 092926

Gateway

ALM

ACT

TGM550Console

ASB

ETR

RST

LineTru nk

1234

Analog

ALM

ACT

TIM514Line

5678

Line

1234

E1/T1

ALM

ACT

TIM510

TST

SIG

SOEISMEMSIEO

BRI

ALM

ACT

TIM5214

CONSOLEAUXUSB

J4350

POWER

POWERRESET

CONFIG

STATUS

ALARM

10/100/1000

0/0 0/10/20/3

LINKTX/RX

LINKTX/RXLINKTX/RX

TX/RXLINK

6 Quick Start for Hardware Installation: IG550 Integrated Gateway

Connecting the LAN and your laptop after

using Disk on Key

1. With an RJ-45 Ethernet cable, cable an Ethernet port (Eth 0) of the Juniper Services Router.

2. Connect your PC or laptop to the console port of the Juniper Services Router

3. Configure your laptop:

●Turn on the power to the management device. Start your asynchronous terminal emulation

application (such as Microsoft Windows Hyperterminal) and select the appropriate COM port to

use (for example, COM1).

qsmalape LAO 092906

Gateway

ALM

ACT

TGM550Console

ASB

ETR

RST

Line

Tru nk

1234

Analog

ALM

ACT

TIM514Line

5678

Line

1234

E1/T1

ALM

ACT

TIM510

TST

SIG

SOEISMEMSIEO

BRI

ALM

ACT

TIM5214

CONSOLEAUXUSB

J4350

POWER

POWERRESET

CONFIG

STATUS

ALARM

10/100/1000

0/0 0/10/2 0/3

LINKTX/RX

LINKTX/RXLINKTX/RX

TX/RXLINK

Juniper

NETWORKS

qsmalapa LAO 092906

Gateway

ALM

ACT

TGM550Console

ASB

ETR

RST

Line

Trunk

1234

Analog

ALM

ACT

TIM514Line

5678

Line

1234

E1/T1

ALM

ACT

TIM510

TST

SIG

SOEISMEMSIEO

BRI

ALM

ACT

TIM5214

CONSOLEAUXU

J4350

POWER

POWERRESET

CONFIG

STATUS

ALARM

10/100/1000

0/0 0/1 0/2 0/3

LINKTX/RX

LINKTX/RXLINKTX/RX

TX/RX LINK

Juniper

NETWORKS

Quick Start for Hardware Installation: IG550 Integrated Gateway

03-601553 Issue 1 February 2007 7

●Configure the port settings as follows:

- Bits per second: 9600

- Data bits: 8

-Parity:None

- Stop bits: 1

- Flow control: None

Finish configuring the router after using Disk on Key

1. Connect the USB modem to one of the USB ports.

2. Log in to the router with the root login and password. If a password has not been established, leave

the password field blank.

3. Upgrade the JUNOS software on the router, if necessary. See Juniper J-Series Services Router

documentation.

4. Go to Configuring the TGM550 on page 11.

Configuring the router using the CLI, if Disk

on Key not available

1. With an RJ-45 Ethernet cable, cable an Ethernet port of the Juniper Services Router.

qsmalape LAO 092906

Gateway

ALM

ACT

TGM550Console

ASB

ETR

RST

Line

Tru nk

1234

Analog

ALM

ACT

TIM514Line

5678

Line

1234

E1/T1

ALM

ACT

TIM510

TST

SIG

SOEISMEMSIEO

BRI

ALM

ACT

TIM5214

CONSOLEAUXUSB

J4350

POWER

POWERRESET

CONFIG

STATUS

ALARM

10/100/1000

0/0 0/1 0/2 0/3

LINKTX/RX

LINKTX/RXLINKTX/RX

TX/RXLINK

Juniper

NETWORKS

8 Quick Start for Hardware Installation: IG550 Integrated Gateway

2. Connect your PC or laptop to the console port of the Juniper Services Router

3. Configure your laptop:

●Turn on the power to the management device. Start your asynchronous terminal emulation

application (such as Microsoft Windows Hyperterminal) and select the appropriate COM port to

use (for example, COM1).

●Configure the port settings as follows:

- Bits per second: 9600

- Data bits: 8

-Parity:None

- Stop bits: 1

- Flow control: None

4. Log in to the router with the root login and password. If a password has not been established, leave

the password field blank.

5. At the root prompt (%), enter cli.

qsmalapa LAO 092906

Gateway

ALM

ACT

TGM550Console

ASB

ETR

RST

Line

Trunk

1234

Analog

ALM

ACT

TIM514Line

5678

Line

1234

E1/T1

ALM

ACT

TIM510

TST

SIG

SOEISMEMSIEO

BRI

ALM

ACT

TIM5214

CONSOLEAUXU

J4350

POWER

POWER RESET

CONFIG

STATUS

ALARM

10/100/1000

0/0 0/1 0/2 0/3

LINKTX/RXLINKTX/RX LINKTX/RXTX/RX LINK

Juniper

NETWORKS

Quick Start for Hardware Installation: IG550 Integrated Gateway

03-601553 Issue 1 February 2007 9

6. At the cli prompt (>), type show interfaces ge-0/0/<x>, where <x> is the port that

you are using, which can be 1, 2, or 3.

7. Check the Hardware address for the router port you are going to administer for Ethernet

connections, for example ge-0/0/3. The Hardware address, which is also called the MAC address,

in the example is 00:12:1e:a9:7a:00.

8. At the cli prompt (>), enter configure.

9. At the configure prompt (#), enter the following:

●If a root password has not already been set, set system root-authentication

plain-text-password, and a new password at the prompt, which you must enter twice.

●set system time-zone <time-zone>

where <time-zone> is the name of the name of the time zone, identified by continent and city.

Use the ?option to see the list of time zones.

●set system host-name <host-name>

where <host-name> is the name of the Juniper Services Router to be accessed on the LAN/

WAN

●set interfaces ge-0/0/<#> unit 0 family inet address <IP_address1>/24 arp

<IP_address2> mac <mac_address> publish

where <#> is the Gigabit port number (1, 2, or 3) you want, <IP_address1> is the address of

the router, <IP_address2> is the address of the TGM550, and <mac_address> is the mac

address of the port you are configuring for Ethernet connections.

Physical interface: ge-0/0/3, Enabled, Physical link is Up

Interface index: 137, SNMP ifIndex: 38

Link-level type: Ethernet, MTU: 1514, Speed: 100mbps, Loopback: Disabled,

Source filtering: Disabled, Flow control: Enabled, Auto-negotiation: Enable

Remote fault: Online

Device flags : Present Running

Interface flags: SNMP-Traps Internal: 0x4000

Link flags : None

CoS queues : 8 supported, 8 maximum usable queues

Current address: 00:12:1e:a9:7a:00, Hardware address: 00:12:1e:a9:7a:00

Last flapped : 2006-11-06 10:36:48 MST (1w0d 23:41 ago)

Input rate : 2496 bps (4 pps)

Output rate : 1736 bps (1 pps)

Active alarms : None

Active defects : None

Logical interface ge-0/0/0.0 (Index 67) (SNMP ifIndex 42)

Flags: SNMP-Traps Encapsulation: ENET2

Protocol inet, MTU: 1500

Flags: Is-Primary

Addresses, Flags: Is-Default Is-Preferred Is-Primary

Destination: 135.9.77/24, Local: 135.9.77.176, Broadcast: 135.9.77.25

10 Quick Start for Hardware Installation: IG550 Integrated Gateway

●set interfaces vp-<slot_number>/0/0 unit 0 family inet address

<internal_ip_address>/32 destination <tgm550_IP_address>,

where <internal_ip_address> is the address the TGM550 uses to telnet to the router and

<tgm550_IP_address> is the IP address for accessing the TGM550.

●set system name-server <IP_address>

where <IP_address> is the address of a DNS server on the LAN/WAN. Repeat this command

for any additional DNS servers the TGM550 might access.

●set system services ssh root-login allow

to allow access to the router with ssh.

●set system services telnet

to allow access to the router with telnet.

●set system domain-search <domain_name>

where <domain-name> is the name of the Juniper Services Router’s network or subnetwork.

Repeat this command for any additional domains the TGM550 might access.

●set system domain-name <domain_name>

where <domain-name> is the name of the Juniper Services Router’s domain.

●set system ntp server <IP_address>

where <IP_address> is the address of an NTP server for time synchronization.

●set interface lo0 unit 0 family inet address <IP_address>

where <IP_address> is the loopback address of the Juniper Services Router

●set system login user <user_name> class super-user

where <user_name> is the user login to the router from TGM550.

Complete the password prompts.

●set system login user <user_name> authentication plain-text-password.

At the two password prompts, enter the password.

!CAUTION:

CAUTION: If a root password has not been set, you must set a new password before you commit

the configuration. Check with your Project Manager to get the password.

10. At the prompt, type commit.

The system may take some time to commit the commands and reset.

11. Configure the MGC list.

a. At the configure prompt (#), enter exit.

Autres manuels pour IG550

Table des matières

Autres manuels Avaya Porte

Avaya

Avaya G650 Manuel utilisateur

Avaya

Avaya G430 Guide de démarrage rapide

Avaya

Avaya G450 Manager Mode d’emploi

Avaya

Avaya RAD IPmux-14 TDMoIP Supplément

Avaya

Avaya Media Gateway G250 Manuel utilisateur

Avaya

Avaya MULTIVOIP MVP-130 Dimensions

Avaya

Avaya Media Gateway G350 Mode d’emploi

Avaya

Avaya Media Gateway G350 Manuel utilisateur

Avaya

Avaya G700 Mode d’emploi

Avaya

Avaya Media Gateway G350 Mode d’emploi

Avaya

Avaya G700 Manuel utilisateur

Avaya

Avaya VSU 10000 Manuel de service

Avaya

Avaya Residential Gateway-I Manuel utilisateur

Avaya

Avaya CMC1 Guide de démarrage rapide

Avaya

Avaya ClearOne Converge Pro VH20 Supplément

Avaya

Avaya Advanced Gateway 2330 Manuel utilisateur

Avaya

Avaya W310 Manuel utilisateur

Avaya

Avaya 3100 Guide de configuration rapide

Avaya

Avaya S8500 Series Manuel utilisateur

Avaya

Avaya G450 Manager Manuel utilisateur

Avaya

Avaya CMC1 Manuel utilisateur

Avaya

Avaya Remote Gateway 911 Series Manuel utilisateur

Avaya

Avaya Media Gateway G250 Manuel d'installation et d'exploitation

Avaya

Avaya G250 Series Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur