AudioCodes Mediant 1000 Manuel utilisateur

™Mediant Digital Media Gateways

Mediant 1000 MGCP, MEGACO, SIP & H.323

Document #: LTRT-63802 February 2006

Fast Track Guide 4.8

Fast Track Guide Contents

Version 4.8 3 February 2006

Table of Contents

1Quick Start ...................................................................................................................7

2Installing the Mediant 1000.........................................................................................8

2.1 Unpacking..........................................................................................................................8

2.2 Package Contents .............................................................................................................8

2.3 Mounting the Mediant 1000 ...............................................................................................9

2.3.1 Mounting the Mediant 1000 on a Desktop...........................................................................9

2.3.2 Installing the Mediant 1000 in a 19-inch Rack.....................................................................9

2.4 Cabling the Mediant 1000................................................................................................10

3Configuring the Mediant 1000 ..................................................................................12

3.1 Assigning the Mediant 1000 IP Address..........................................................................12

3.1.1 Assigning an IP Address Using HTTP ...............................................................................12

3.1.2 Assigning an IP Address Using BootP...............................................................................13

3.1.3 Assigning an IP Address Using the CLI.............................................................................14

3.2 Restoring Networking Parameters to their Initial State ....................................................15

3.3 Accessing the Embedded Web Server ............................................................................15

3.4 Configuring the Mediant 1000 Basic Control Protocol Parameters .................................16

3.4.1 Configuring Basic MGCP / MEGACO Parameters ............................................................17

3.4.2 Configuring Basic H.323 Parameters ................................................................................19

3.4.3 Configuring Basic SIP Parameters ....................................................................................21

3.5 Configuring the Trunk Settings ........................................................................................23

4Changing the Mediant 1000 Username and Password...........................................26

5Restoring and Backing Up the Mediant 1000 Configuration .................................27

6Monitoring the Mediant 1000....................................................................................28

6.1 Monitoring the Mediant 1000 LEDs .................................................................................28

6.2 Monitoring the Mediant 1000 Trunks and B-channels .....................................................29

7Upgrading the Mediant 1000.....................................................................................30

7.1 Software Upgrade Wizard................................................................................................30

7.2 Updating the Auxiliary Files .............................................................................................34

Mediant 1000 Digital

Fast Track Guide 4 Document #: LTRT-63802

List of Figures

Figure 1-1: Required Steps to Install the Mediant 1000 .....................................................................................7

Figure 2-1: Pinout of the RJ-48c Trunk Connectors.........................................................................................10

Figure 2-2: RJ-45 Ethernet Connector Pinout ..................................................................................................11

Figure 3-1: Client Configuration Screen with Blank Parameters......................................................................14

Figure 3-2: Embedded Web Server Login Screen ...........................................................................................15

Figure 3-3: Mediant 1000 MGCP/MEGACO Quick Setup Screen ...................................................................17

Figure 3-4: Mediant 1000/H.323 Quick Setup ..................................................................................................19

Figure 3-5: Mediant 1000/SIP Quick Setup......................................................................................................21

Figure 3-6: Trunk Settings Screen....................................................................................................................23

Figure 4-1: Web User Accounts Screen ...........................................................................................................26

Figure 5-1: Configuration File Screen...............................................................................................................27

Figure 6-1: Location of Front Panel LEDs ........................................................................................................28

Figure 6-2: Trunk & Channel Status Screen ....................................................................................................29

Figure 7-1: Start Software Upgrade Screen .....................................................................................................30

Figure 7-2: Load a cmp File Screen .................................................................................................................31

Figure 7-3: cmp File Successfully Loaded into the Mediant 1000 Notification.................................................31

Figure 7-4: Load an ini File Screen ..................................................................................................................32

Figure 7-5: Load a CPT File Screen.................................................................................................................32

Figure 7-6: FINISH Screen ...............................................................................................................................33

Figure 7-7: ‘End Process’ Screen.....................................................................................................................33

Figure 7-8: Auxiliary Files Screen (MGCP / MEGACO Gateways) ..................................................................35

List of Tables

Table 3-1: Mediant 1000 Default Networking Parameters ...............................................................................12

Table 3-2: Trunks Status Color Indicator Keys.................................................................................................23

Table 6-1: Functionality of the Front Panel LEDs.............................................................................................28

Table 7-1: ini and Auxiliary Files Descriptions..................................................................................................34

Fast Track Guide Notices

Version 4.8 5 February 2006

Notices

Notice

This Fast Track Installation Guide describes the installation of the AudioCodes Mediant 1000 MGCP,

MEGACO, SIP and H.323 Digital media gateways.

Information contained in this document is believed to be accurate and reliable at the time of printing.

However, due to ongoing product improvements and revisions, AudioCodes cannot guarantee the

accuracy of printed material after the Date Published nor can it accept responsibility for errors or

omissions. Updates to this document and other documents can be viewed by registered Technical

Support customers at http://www.audiocodes.com under Support / Product Documentation.

This document is subject to change without notice.

Date Published: Feb-28-2005 Date Printed: Mar-02-2006

Tip: When viewing this manual on CD, Web site or on any other electronic copy, all

cross-references are hyperlinked. Click on the page or section numbers (shown

in blue) to reach the individual cross-referenced item directly. To return back to

the point from where you accessed the cross-reference, press the ALT and ◄

keys.

Trademarks (Heading style)

AC logo, Ardito, AudioCoded, AudioCodes, AudioCodes logo, IPmedia, Mediant, MediaPack, MP-

MLQ, NetCoder, Stretto, TrunkPack, VoicePacketizer and VoIPerfect, are trademarks or

registered trademarks of AudioCodes Limited. All other products or trademarks are property of

their respective owners.

WEEE EU Directive

Pursuant to the WEEE EU Directive, electronic and electrical waste must not be disposed of with

unsorted waste. Please contact your local recycling authority for disposal of this product.

Customer Support

Customer technical support and service are provided by AudioCodes’ Distributors, Partners, and

Resellers from whom the product was purchased. For Customer support for products purchased

directly from AudioCodes, contact support@audiocodes.com.

Abbreviations and Terminology

Each abbreviation, unless widely used, is spelled out in full when first used, and only Industry

standard terms are used throughout this manual. The symbol 0x indicates hexadecimal notation.

Mediant 1000 Digital

Fast Track Guide 6 Document #: LTRT-63802

Related Documentation

Document # Manual Name

LTRT-664xx (e.g., LTRT-66401) Mediant 1000 MGCP-MEGACO Digital Gateways User’s Manual

LTRT-819xx TP Series Digital Gateways Release Notes

LTRT-699xx Mediant Series & TP-1610 H.323 Digital Gateways User's Manual

LTRT-696xx Mediant Series & TP-1610 H.323 Digital Gateways Release Notes

LTRT-688xx Mediant & TP Series SIP Digital Gateways User's Manual

LTRT-690xx Mediant & TP Series SIP Digital Gateways Release Notes

Warning: The Mediant 1000 is supplied as a sealed unit and must only be serviced

by qualified service personnel

Note: Where ‘network’ appears in this manual, it means LAN, WAN, etc. accessed via

the gateway’s Ethernet interface.

Fast Track Guide 1. Quick Start

Version 4.8 7 February 2006

1 Quick Start

This Fast Track Installation Guide helps you to set up the Mediant 1000 for the first time. Prior

knowledge of IP networks is preferred. Refer to Figure 1-1 for the quick setup flow. For detailed

information on how to fully configure the gateway, refer to the digital Mediant 1000 User’s

Manuals.

Figure 1-1: Required Steps to Install the Mediant 1000

Refer to Section 2.4

Refer to Section 3.1

Refer to Section 2.3

Refer to Section 2.1

Refer to Section 3.5

Refer to Section 3.4

Mediant 1000 Digital

Fast Track Guide 8 Document #: LTRT-63802

2 Installing the Mediant 1000

Caution Electrical Shock

The equipment must only be installed or serviced by qualified service personnel.

¾To install your Mediant 1000, take these 4 steps:

1. Unpack the Mediant 1000 (refer to Section 2.1 below).

2. Check the package contents (refer to Section 2.2 below).

3. Mount the Mediant 1000 (refer to Section 2.3 on page 9).

4. Cable the Mediant 1000 (refer to Section 2.4 on page 10).

After connecting the Mediant 1000 to the power source, the power LED on the front panel of the

power supply unit is lit green (after a self-testing period of about 2 minutes). Any power supply

malfunction results in the LED switching off (refer to 6.1 on page 28 for details on the Mediant

1000 LEDs).

When you have completed the above relevant sections you are then ready to start configuring the

gateway (Section 3on page 12).

2.1 Unpacking

¾To unpack the Mediant 1000, take these 6 steps:

1. Open the carton and remove packing materials.

2. Remove the Mediant 1000 from the carton.

3. Check that there is no equipment damage.

4. Check, retain and process any documents.

5. Notify AudioCodes or your local supplier of any damage or discrepancies.

6. Retain any diskettes or CDs.

2.2 Package Contents

Ensure that in addition to the Mediant 1000, the package contains:

One or two AC power cables.

Four anti-slide bumpers for desktop installation option (supplied in a small plastic bag).

CD (software and documentation).

RS-232 DB9 adapting cable, two meters in length (direct connection to PC).

This Mediant 1000 Digital Fast Track Installation Guide.

Fast Track Guide 2. Installing the Mediant 1000

Version 4.8 9 February 2006

2.3 Mounting the Mediant 1000

The Mediant 1000 can be mounted on a desktop, or installed in a standard 19-inch rack. For

detailed information on cabling the Mediant 1000, refer to Section 2.4 on page 10.

2.3.1 Mounting the Mediant 1000 on a Desktop

The integral front brackets are not required for a desktop installation. Optionally, attach the four

(supplied) anti-slide bumpers to the base of the Mediant 1000 and place it on the desktop in the

position you require.

2.3.2 Installing the Mediant 1000 in a 19-inch Rack

Users can install the Mediant 1000 in a standard 19-inch rack either by placing it on a shelf

preinstalled in the rack (preferred method), or by attaching it directly to the rack’s frame. If the

rack is without shelves, it is advised to acquire shelves.

Installation of a Mediant 1000 in a rack without shelves requires users to directly attach the

Mediant 1000 integral front brackets and the user-adapted rear brackets (not provided) to the

rack’s frame.

Note: Users assembling the rear brackets by themselves should note the following:

•The distance between the screws on each bracket is 28 mm.

•To attach the brackets, use 4-40 screws with a maximal box penetration

length of 3.5 mm.

¾To place the Mediant 1000 on a 19-inch rack’s shelf, take these 2 steps:

1. Place the Mediant 1000 on a preinstalled shelf.

2. It is recommended to attach the Mediant 1000 integral front brackets to the frame of the rack

to prevent it from sliding off the shelf during cabling. Use standard 19-inch rack bolts (not

provided) to fasten the front of the Mediant 1000 to the frame of the rack.

¾To install the Mediant 1000 in a rack without shelves, take these 2 steps:

1. Position the Mediant 1000 in your 19-inch rack and align the front and rear bracket holes to

holes (of your choosing) in the vertical tracks of the 19-inch rack.

2. Use standard 19-inch rack bolts (not provided) to fasten the brackets to the frame of the

rack.

Mediant 1000 Digital

Fast Track Guide 10 Document #: LTRT-63802

Rack Mount Safety Instructions (UL)

When installing the chassis in a rack, be sure to implement the following safety

instructions recommended by Underwriters Laboratories:

•Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the

operating ambient temperature of the rack environment may be greater than room

ambient. Therefore, consideration should be given to installing the equipment in an

environment compatible with the maximum ambient temperature (Tma) specified by

the manufacturer.

•Reduced Air Flow - Installation of the equipment in a rack should be such that the

amount of air flow required for safe operation on the equipment is not compromised.

•Mechanical Loading - Mounting of the equipment in the rack should be such that a

hazardous condition is not achieved due to uneven mechanical loading.

•Circuit Overloading - Consideration should be given to the connection of the

equipment to the supply circuit and the effect that overloading of the circuits might

have on overcurrent protection and supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

•Reliable Earthing - Reliable earthing of rack-mounted equipment should be

maintained. Particular attention should be given to supply connections other than direct

connections to the branch circuit (e.g., use of power strips.)

2.4 Cabling the Mediant 1000

Protective Earthing

The equipment is classified as Class I EN60950 and UL60950 and must be earthed at all

times. Units providing power sockets with three pins must be connected by service

personnel to a socket-outlet with a protective earthing connection.

¾To cable the Mediant 1000, take these 7 steps:

1. The Mediant 1000 must be permanently earthed using an equipment-earthing conductor.

Connect an electrically earthed strap of 16 AWG wire (minimum) to the chassis earthing

screw, using the supplied washer. The connection to the protective earthing should be in

accordance with the regulations enforced in the country of installation.

2. Connect the E1/T1 trunk cables to the ports on the I/O module/s. Connect the other ends of

the trunk cables to your PBX/PSTN switch.

For a 1+1 or 2+2 fallback option, connect trunks 1 and 3 to your PBX and trunks 2 and 4 to

the PSTN. If the power fails, a relay connects trunks 1 to 2 and 3 to 4 (in the same module)

acting as a fallback for PSTN trunks.

To protect against electrical shock and fire, use a 26 AWG min wire to connect T1 or E1

ports to the PSTN.

RJ-48c trunk connectors are wired according to Figure 2-1 below.

Figure 2-1: Pinout of the RJ-48c Trunk Connectors

1 2 3 4 5 6 7 8 3, 6, 7, 8

not connected

body = shield

1 = Rx RING

2 = Rx TIP

4 = Tx RING

5 = Tx TIP

RJ-48c Connector and Pinout

Autres manuels pour Mediant 1000

Table des matières

Autres manuels AudioCodes Porte

AudioCodes

AudioCodes Mediant 3000 Instructions de montage

AudioCodes

AudioCodes Mediant 1000 Instructions de montage

AudioCodes

AudioCodes MP-272-DB Manuel utilisateur

AudioCodes

AudioCodes Mediant 800B Manuel utilisateur

AudioCodes

AudioCodes Mediant 2000 Instructions de montage

AudioCodes

AudioCodes i Series Instructions de montage

AudioCodes

AudioCodes Mediant 2000 Manuel utilisateur

AudioCodes

AudioCodes MediaPack MP-114 Manuel utilisateur

AudioCodes

AudioCodes Mediant 3000 TP-6310 Manuel d'installation et d'exploitation

AudioCodes

AudioCodes Mediant 800C SBC Guide de référence rapide

AudioCodes

AudioCodes MP-5 Series Manuel utilisateur

AudioCodes

AudioCodes MediaPack MP-402 Manuel utilisateur

AudioCodes

AudioCodes MP-11 Manuel utilisateur

AudioCodes

AudioCodes Gateway & Session Border Controller Series Instructions de montage

AudioCodes

AudioCodes mediapack MP-500 Manuel utilisateur

AudioCodes

AudioCodes MP-108 Manuel utilisateur

AudioCodes

AudioCodes Mediant 800 Manuel utilisateur

AudioCodes

AudioCodes MediaPack MP-124 Manuel utilisateur

AudioCodes

AudioCodes MediaPack MP-262 Manuel utilisateur

AudioCodes

AudioCodes MediaPack 504 Instructions de montage

AudioCodes

AudioCodes Mediant 500L MSBR Manuel utilisateur

AudioCodes

AudioCodes Mediant Series Guide de démarrage rapide

AudioCodes

AudioCodes MediaPack 114 Manuel utilisateur

AudioCodes

AudioCodes MP-104 Mode d’emploi

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur