Audio Technica AT-ONE Manuel du propriétaire

UHF Wireless Microphone System

Installation and Operation

Contents

Introduction

- Introduction 1

- Safety 1

System Functions

- Receiver Functions 2-3

- Handheld Transmitter Functions 4

- BodypackTransmitter Functions 5

- Battery Status 6

System Operation

- System Setup 6

- Receiver Operation 7

- Transmitter Operation 8

- Squelch 9

- Frequencies 9

- Troubleshooting 10

- Rack Mount Setup 11

Speciﬁcations

- Overall Speciﬁcation 12

- Receiver Speciﬁcation 12

- Bodypack Transmitter Speciﬁcation 13

- Handheld Transmitter Speciﬁcation 13

Compliance

- WEEE Regulations 14

- Declaration of Compliance 15

Introduction

Thank you for purchasing this Audio-Technica product. This PLL synthesized wireless microphone

system operates in the UHF band frequency, with two groups of four frequencies. Please read this

manual carefully before operating the AT-One system.This manual covers the function and operation of

the wireless microphone system.

Safety

- To prevent ﬁre or shock hazard, do not expose this appliance to rain or moisture

- To prevent ﬁre, do not cover the ventilation of the apparatus with newspaper, tablecloths, etc.

- Do not expose this apparatus to drips or splashes

- Do not place any objects ﬁlled with liquids, such as vases, on the apparatus

- Do not install this apparatus in a conﬁned space such as a bookcase or similar unit

- The aparatus should be located close enough to the AC outlet so that you can easily grasp the

AC adapter at any time. In case of emergency, disconnect the AC adapter quickly.

- Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent

type.

- If the transmitter is not in use for an extended period, remove the batteries to avoid damage

- Do not dispose of used batteries with domestic rubbish. Be sure to dispose of batteries in

accordance with your local waste disposal rules.

- When disposing of the equipment, remove the batteries, separate the case, circuit boards and

cables, and dispose of all components in accordance with local waste disposal rules.

The circuits inside the receiver and transmitter have been precisely adjusted for optimum performance

and compliance with government regulations. Do not attempt to open the receiver or transmitter. To do

so will void the warranty, and may cause improper operation.

Receiver Functions

Receiver Front:

1. Antenna: Detachable UHF antenna with BNC connector

2. Power Button

3. RF Red LED: Displays the reception status of the RF signal

4. AF Green LED: Displays the reception status of the AF signal

5. UP Channel Button: Tap forward to select an interference free channel

6. DOWN Channel Button: Tap backward to select an interference free channel

Receiver Functions

Receiver Rear:

1. Antenna BNC Receptacle: This provides a connection to the supplied antennas or to

coaxial cable used with an antenna divider, antenna

booster or remote antennas

2. Balanced XLR Audio Output

3. Unbalanced 1/4” Jack Output

4. Mic/Line Switch: Use this to adjust the audio output of the wireless

microphone system for mic level (-20dB) or line-level

(0dB)

5. SQ (Squelch): Turn the squelch to the lowest possible setting (counter

clockwise) to eliminate any interfering signals. In RF

crowded environments (other wireless microphones, LTE,

etc.) it can be required to increase the squelch level

(clock wise) to block out unwanted noise. Please note

that this will reduce the operating distance of the system,

so always seek the lowest possible setting.

6. DC IN: DC input connector for the supplied AC adapter

7. Cable Strain

Transmitter Functions

Handheld Transmitter:

1. Power/Mute Button

2. Power/Mute/Battery Status LED Indicates the power/mute/battery level status

3. Channel Selector: Change the channel setting from 11-14 or 21-24

4. Battery Compartment: Insert two AA batteries making sure the polarity is correct

5. Grille: Protects the microphone capsule and protects against wind

and breath sound

Transmitter Functions

Bodypack Transmitter:

1. Antenna

2. Power/Mute Button

3. Power/Mute/Battery Status LED: Indicates the power/mute/battery level status

4. Input Connector: 4-pin locking connector (HRS)

5. Channel Selector: Change the channel setting from 11-14 or 21-24

6. Gain: Rotary control adjusts the sensitivity of the

transmitter’s audio to the level of the connected

mic or instrument

7. 10dB Switch: Activate this switch to attenuate the signal by

an additional 10dB.

8. Battery Compartment: Insert two AA batteries making sure the polarity is

correct

Transmitter Functions

LED Status

Green Ready

Red Muted

Green Flashing On, low battery

Red Flashing Muted, low battery

No Light No power

Power/Battery Status LED:

System Operation

System Setup:

For best operation the receiver should be at least 1 m above the ground and at least 1m away from a

wall or metal surface to minimize reﬂections. The transmitter should be at least 2m from the receiver,

as shown in in the diagram below. Keep antennas away from noise sources such as digital equipment,

motors, automobiles and neon lights, as well as away from large metal objects.

2 m

1 m

System Operation

Connecting the receiver:

Plug the DC 12V 500mA power supply into the

power connector on the back of the receiver.

The power connector is supplied with

interchangable UK and EU adaptors.

Connect the receiver output to an audio mixer

or ampliﬁer input, using a standard audio cable

with 3-pin XLR or 6.35mm Jack connectors.

Never use balanced and unbalanced audio

outputs at the same time, this may cause

signal loss or increased noise.

Set the attenuation for mic or line input.

Two-position switch adjusts the audio output

attenuation to 0 dB or -20 dB. The factory

setting is 0 dB.

Line Mic

System Operation

Handheld Microphone/Bodypack Transmitter set up:

Open the battery cover and insert AA batteries into

the battery compartment making sure the polarity

is correct.

Unscrew the bottom of the handheld mic and open

the battery cover to insert AA batteries into the

battery compartment, making sure the polarity is

correct.

Press and hold the power button on the micro-

phone/bodypack transmitter for 4 seconds to turn

on. If the LED remains ﬂashing after 4 seconds it is

indicating that the battery is low on power.

Use the included key to adjust the frequency of the

transmitter to be the same as the receiver.

Use the 0dB/-10dB switch to adjust the audio input

level.

0dB -10dB

Table des matières

Autres manuels Audio Technica Système de microphone

Audio Technica

Audio Technica ATW-901a/L Manuel utilisateur

Audio Technica

Audio Technica 2000 Series Guide d'installation

Audio Technica

Audio Technica ATCS-60 Manuel utilisateur

Audio Technica

Audio Technica UniPak ATW-1661 Manuel du propriétaire

Audio Technica

Audio Technica ATW-702 Manuel du propriétaire

Audio Technica

Audio Technica ATW-1811 Guide de configuration

Audio Technica

Audio Technica ATW-0951 Manuel du propriétaire

Audio Technica

Audio Technica Pro Series 5 Manuel du propriétaire

Audio Technica

Audio Technica ATW-901a/G Manuel utilisateur

Audio Technica

Audio Technica ATW-R1810 Manuel du propriétaire

Audio Technica

Audio Technica ATW-1821 Manuel utilisateur

Audio Technica

Audio Technica ES954 Manuel utilisateur

Audio Technica

Audio Technica ATR100G Manuel utilisateur

Audio Technica

Audio Technica ATW-DA600 Manuel d'utilisation

Audio Technica

Audio Technica ATCS-60 Manuel utilisateur

Audio Technica

Audio Technica ATW-A20 Manuel du propriétaire

Audio Technica

Audio Technica ATW-600 Manuel d'utilisation

Audio Technica

Audio Technica 3000 Series Mode d'emploi

Audio Technica

Audio Technica PRO 127G Manuel du propriétaire

Audio Technica

Audio Technica 5000 Series Manuel utilisateur

Audio Technica

Audio Technica ATW-A54P Manuel du propriétaire

Audio Technica

Audio Technica 3000 Series Manuel utilisateur

Audio Technica

Audio Technica GENUINE AT8688 Manuel utilisateur

Audio Technica

Audio Technica Professional 2000 Series Manuel utilisateur

Manuels Système de microphone populaires d'autres marques

Paso

Paso R824 Manuel utilisateur

Naxa

Naxa NAM-982 Manuel utilisateur

Motorola

Motorola PMNN4461 Manuel utilisateur

Xvive

Xvive U3 Manuel utilisateur

Tekon

Tekon DUOS Manuel utilisateur

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuel utilisateur

Devine

Devine WMD-IE Manuel utilisateur

LG LF-D7150 Manuel utilisateur

GE S768DAV Manuel utilisateur

LD U305 HBH 2 Manuel utilisateur

Chainway

Chainway URA8 Manuel utilisateur

ORATOR

ORATOR D860TD Manuel utilisateur

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuel utilisateur

Alpha Technologies

Alpha Technologies RBMS Manuel utilisateur

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuel utilisateur

Shure

Shure UA844 Manuel utilisateur

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuel utilisateur

Pyle

Pyle PDWM5000 Manuel utilisateur