Tekon DUOS Manuel utilisateur

TEKON ELECTRONICS AVEIRO, PORTUGAL

P.: +351 234 303 320 M.: +351 933 033 250 E.: sales@tekonelectronics.com

DUOS WIRELESS SYSTEM

INSTALLATION GUIDE

TEKON ELECTRONICS AVEIRO, PORTUGAL

P.: +351 234 303 320 M.: +351 933 033 250 E.: sales@tekonelectronics.com

IG.DUOS.ENG.V01.3.2018

DUOS WIRELESS SYSTEM INSTALLATION GUIDE

step

CONNECT AND CONFIGURE THE DUOS WIRELESS GATEWAY

Pages 4 to 10

CONNECT AND CONFIGURE THE DUOS WIRELESS TRANSMITTER

Pages 11 to 15

DUOS WIRELESS SYSTEM

INSTALLATION GUIDE

Table of contents

DUOS WIRELESS SYSTEM INSTALLATION GUIDE

step

CHECK WIRELESS COMMUNICATION BETWEEN THE DUOS TRANSMITTER AND THE GATEWAY

Page 16

CONNECT AND CONFIGURE THE DUOS WIRELESS REPEATER

Pages 17 to 22

DUOS WIRELESS SYSTEM

INSTALLATION GUIDE

Table of contents

DUOS WIRELESS SYSTEM INSTALLATION GUIDE

step

CONNECT AND CONFIGURE THE DUOS WIRELESS GATEWAY

01 Connect the antenna to the Gateway.

02 Connect the DUOS RS485-USB cable to the

computer and then to the Gateway.

03 Check the device connection through the LED signage.

If the red and blue LEDs are active, both the cable and Gateway are working correctly.

LED ashes slowly

LED switched on and steady

Red LED ashes every second

whenever it sends beacons to new

elements to join the network

Green LED ashes as soon as the

device receives data from other

equipment

10 Seconds to enter

conguration mode

TEKON CONFIGURATOR SOFTWARE is only compatible with the Microsoft Windows Operating System.

step

CONNECT AND CONFIGURE THE DUOS WIRELESS GATEWAY

DUOS WIRELESS SYSTEM INSTALLATION GUIDE

04 Open Tekon Congurator Software1and select from the menu DUOS >> Gateway >> Conguration

05 Select the Serial Port of the DUOS Wireless Gateway

Click on the Refresh Serial Ports button.

1 Tekon Congurator software is free of charge and available at www.tekonelectronics.com

DUOS WIRELESS SYSTEM INSTALLATION GUIDE

step

CONNECT AND CONFIGURE THE DUOS WIRELESS GATEWAY

06 Select the Port name2of the device.

07 Remove the DUOS RS485-USB cable from the

Gateway side and reinsert it.

NOTE:

After reinserting the cable, you have 10 seconds to enter in conguration mode by clicking on the Connect ( )

button, while the blue LED ashes slowly.

In this mode, you can manage the device parameters: Modbus Address, Modbus baud rate, Modbus Parity, Wire-

less Network ID and Wireless Channel.

2You can check the device port name in the Device Manager menu in the Windows operating system.

step

CONNECT AND CONFIGURE THE DUOS WIRELESS GATEWAY

DUOS WIRELESS SYSTEM INSTALLATION GUIDE

10 Seconds to enter

conguration mode

LED ashes slowly

LED ashes quickly

LED switched on and steady

Click on the Connect ( ) button to enter conguration mode.

The status string at the bottom of the software window gives feedback of reading operations, as well as the

Gateway LED indication.

NOTE:

When 10 seconds have been exceeded, the blue LED is steady and it is no longer possible to enter conguration

mode. In this case, the cable must be removed and reiserted - step 2.

DUOS WIRELESS SYSTEM INSTALLATION GUIDE

step

CONNECT AND CONFIGURE THE DUOS WIRELESS GATEWAY

10 Click on the Disconnect ( ) button.

The Modbus interface and the wireless network are active if the blue LED is on and steady and the red LED is ashing

once per second.

Take note of the device conguration data available, namely: Modbus Address, Modbus Baudrate, Modbus Parity,

Wireless Network ID and Wireless Channel.

NOTE:

The wireless network connection between devices is ensured by the Wireless Network ID and Wireless Channel

eld parameters.

step

CONNECT AND CONFIGURE THE DUOS WIRELESS GATEWAY

DUOS WIRELESS SYSTEM INSTALLATION GUIDE

11 Modbus Communication

Open the Modbus tab of the Gateway and set the previously saved congurations.

Ensure that the Port name, Baudrate, Parity and the Modbus Address elds are the same obtained in conguration mode.

LED switched on and steady

Red LED ashes every second

whenever it sends beacons

to new elements to join the

network.

DUOS WIRELESS SYSTEM INSTALLATION GUIDE

step

CONNECT AND CONFIGURE THE DUOS WIRELESS GATEWAY

The messages Connected to Modbus and Reading successfully will appear if the Serial Port conguration

parameters are correct and the Modbus connection established.

If the blue LED is on and steady and red LED ashes once per second, the Gateway is fully operational on the

Modbus and wireless interfaces.

Click on the Connect ( ) button and check the operation status at the bottom of the window.

Autres manuels Tekon Système de microphone

Tekon

Tekon PLUS TWPH-1UT Manuel utilisateur

Tekon

Tekon Plus Series Manuel utilisateur

Tekon

Tekon PLUS TWP4AI Manuel utilisateur

Tekon

Tekon PLUS TWP4AI Manuel utilisateur

Manuels Système de microphone populaires d'autres marques

Paso

Paso R824 Manuel utilisateur

Naxa

Naxa NAM-982 Manuel utilisateur

Motorola

Motorola PMNN4461 Manuel utilisateur

Xvive

Xvive U3 Manuel utilisateur

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuel utilisateur

Devine

Devine WMD-IE Manuel utilisateur

LG LF-D7150 Manuel utilisateur

GE S768DAV Manuel utilisateur

LD U305 HBH 2 Manuel utilisateur

Chainway

Chainway URA8 Manuel utilisateur

ORATOR

ORATOR D860TD Manuel utilisateur

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuel utilisateur

Alpha Technologies

Alpha Technologies RBMS Manuel utilisateur

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuel utilisateur

Shure

Shure UA844 Manuel utilisateur

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuel utilisateur

Pyle

Pyle PDWM5000 Manuel utilisateur

Airspan

Airspan AS4000 Mode d’emploi