ATD Tools ATD-7331A Instructions d'utilisation

ATD-7331A

3-Ton Hydraulic Service Jack

Capacity Min. Height Max Height Handle

Length

Overall

Length

Overall

Width

Saddle

Diameter

Shipping

Weight

3 Ton 5-1/4” 20” 50” 29-3/8” 14-1/4” 5” 92 LB

Contents:

Page

: 1. Speci ca ons

2. Safety & Warning Informa on

3. & 4. Setup, Opera on & Preven ve Maintenance

5. Inspecon, Storage & Troubleshoo ng

6. Exploded View & Replaceable Part Numbers

7. Warranty Informaon

era n

Instruc ons & Parts Manual

Model: ATD – 7331A

Capacity: 3 Ton

ATD7331A_rev_0417

Made in China to ATD Tools, Inc. Specications

Visit us at www.atdtools.com

WARNING: This product may contain chemicals, including lead, known to the State of California

to cause cancer, birth defects or other reproductive harm. Wash hands after handling.

Model:ATD–7331A

Capacity:3Ton

SAFETY & WARNING INFORMATION

IMPORTANT: READ ALL INSTRUCTIONS BEFORE USEΎ

Before operaƟng this device, be sure to read all content within this manual, ensuring that you

understand the operaƟng procedures, maintenance requirements and all safety warnings.

The owner and/or operator shall have an understanding of the product, its operaƟng

characterisƟcs,andsafetyoperaƟnginstrucƟonsbeforeoperaƟngthisdevice.SafetyinformaƟon

shall be emphasized and understood. If the operator is not Ňuent in English, the product and

safety instrucƟons shall be read to and discussed with the operator in the operator’s naƟve

language by the purchaser/owner or his designee, making sure that the operator comprehends

their contents.

Actions to help prevent dangerous situations

xStudy, understand, and follow all instrucƟons before operaƟng this device.

xDo not exceed the rated capacity stated.

xUse only on hard level surfaces.

xThis item is tobe used as a liŌingdevice only. Immediately aŌer liŌing, support the

vehicle with appropriate means.

xDo not move or dolly the vehicle while it is on the jack.

xLiŌonly on areas of thevehicle as speciĮed by the vehicle manufacturer.

xNo alteraƟonsshall be made to this product.

xFailure to heed these markings may result in serious personal injury and/or property

damage.

ThisisthesafetynoƟĮcaƟonsymbol.

This symbol will noƟfy you of any

potenƟal injury hazards. Please

followallinstrucƟonsthatfollowthis

symbol to avoid possible injuries or

death.

Indicates a hazardous

situaƟon. If proper steps are

not followed, death or

serious injury could result.

Model:ATD–7331A

Capacity:3Ton

SETUP, OPERATION & PREVENTIVE MAINTENANCEΎ

ΎSetupΎ

xPrior to each use, visual inspecƟon (See Pg. 5) shall be made to the device by checking

for abnormal condiƟons, such ascracked welds, leaks, and damaged, loose, or missing

parts.

xConsult the vehicle owner’s manual to determine thelocaƟon of liŌpoints.

xBe sure to set the vehicle in parkwith the emergency brake on and wheelssecurely

chocked.

xBe sure that the vehicle and the jack are on a hard, level surface.Ύ

Assembly

xIf two piece handles are provided, assemble the upper secƟon into the lower secƟon,

line up the holes, insert and Ɵghten the screw.

xInsert the boƩom end of handle into handle fork and securely Ɵghten the bolt and

washer. Ensurethe handle can turn freely.

Lifting

xTurn the handle/release valve clockwise to the closed posiƟon. Do not over Ɵghten.

xPosiƟon the jack under the speciĮed liŌpoint.

xBegin liŌing by pumping the handle up and down.

xImmediately aŌer liŌing,support the vehicle with appropriately rated jack stands.

xTurn the handle/release valve slowly counterclockwise to lowerthe vehicle onto jack

stands.

Lowering

xTurn the handle/releasevalve clockwise to theclosed posiƟon. Do not over Ɵghten.

xPump the handle up and down to liŌvehicle oījack stands.

xRemove the jack stands.Do not getunder orlet anyone get under the vehicle while

lowering.

xTurn the handle/releasevalve slowly counterclockwise to lower the vehicle ontothe

ground.

–ATD 7331AModel:

Capacity:3Ton

SETUP, OPERATION & PREVENTIVE MAINTENANCE (Cont.)

Maintenance

NOTICE: Use high grade hydraulicoil only. Neveruse brake Ňuid, motor oil, transmission Ňuid,

turbine oil or any other Ňuids. ISO-VG22 or equivalenthydraulic oil is recommended.

Check and Refill Oil

xWith the jack in the fully lowered, level posiƟon,if unitcover is provided, remove unit

cover, then remove oil Įller plug.

xProper oil levelshould be just covering inner cylinderas seen fromthe oilĮller plug

hole.

xDo not overĮll. Always Įll with new, clean hydraulicjack oil as recommended above.

xReinstall oil Įller plug, then reinstall unit cover.

Lubrication and Cleaning

xPeriodically clean and lubricate all moving parts and pivot points.

Air Venting Procedures

xWith the jack in the fully lowered posiƟon, release valve open, remove oilĮller plug.

xPump the handle rapidlyseveral Ɵmes. Reinstall oil Įller plug.

xTurn the handle/releasevalve clockwise to theclosed posiƟon.

xPump the handle unƟl the liŌarm reaches maximum height and conƟnue to pump

several Ɵmes to remove trapped air in the system.

xTurn the handle/release valve counterclockwise in one full turn and lowerliŌarm to the

lowest posiƟon. Use force on saddle if necessary.

xCarefully and slowly loosen oil Įller plug to release pressurized air.

xRepeat above steps unƟl trapped airis completely vented.

Damaged Equipment

Any jack that appears to be damaged in any way, is found to be worn, or operates abnormally

SHALL BE REMOVED FROM SERVICE UNTIL REPAIRED. It is recommended that necessary repairs

be made by a manufacturer’s or supplier’s authorized repair facility if repairs are permiƩed by

the manufacturer or supplier.

Alterations

Because of potenƟal hazards associated with thistype of equipment, no alteraƟonsshall be

made to the product.

Attachments and Adapters

Only aƩachments and/or adapters supplied by the manufacturer shall beused.

INSPECTION, STORAGE & TROUBLESHOOTING

InspectionΎ

xVisual inspecƟon shall be made before each use of the device by checking for abnormal

condiƟons, suchas cracked welds, leaks, and damaged, loose, or missing parts.

xOther inspecƟons shall be made per product operaƟng instrucƟons.

xThis device shall be inspected immediately if the device is believed to have been

subjected to an abnormal load or shock. It is recommended that this inspecƟon be made

by a manufacturer’s or supplier’s authorizedrepair facility.

xOwners and/or operators should be awarethat repair of this equipment may require

specialized knowledge and faciliƟes. It is recommended that an annual inspecƟon of the

product be made by a manufacturer’s or supplier’s authorized repair facility and that

any defecƟve parts, decals, or safetylabels or signs be replaced with manufacturer’s or

supplier’s speciĮed parts.

StorageΎ

ΎThis Jack should be stored in a dry locaƟon on a level surface.

–ATD 7331AModel:

Capacity:3Ton

Troubleshooting

Symptom Possible Causes SoluƟon

Jack will not liŌthe load. 1. Release valve not Ɵghtly

closed.

2. Low oil level.

3. DefecƟve or worn internal

parts.

4. Load exceeds maximum

allowance.

1. Tighten release valve.

2. Check and add oil. Follow“Check

and ReĮll Oil” instrucƟons on Pg.4.

3. DisconƟnue use and contact a

local repair center.

4. Use a higher capacity jack.

Jack will not hold the load. 1. Release valve not Ɵghtly

closed.

2. Power unit malfuncƟon.

1. Tighten release valve.

2. DisconƟnue use and contact a

local repair center.

Jack will not descend to

minimum height, or will not

remain in lowered posiƟon.

1. Air trapped in system.

2. Reservoir oil overĮlled. 1. Vent air out of system. Follow “Air

VenƟng Procedures” above.

2. Check and ensure proper oil level.

Follow “Check and ReĮll Oil”

instrucƟon on Pg.4.

Jack will not liŌto max

height. 1. Low oil level. 1. Check and ensure proper oil level.

Follow “Check and ReĮll Oil”

instrucƟons on Pg. 4.

Jack will not funcƟon

properly aŌer tried soluƟon. 1. Internal malfuncƟon or

structural damage. 1. Stop usage and contact an

authorized repair center.

EXPLODED VIEW & REPLACEABLE PART NUMBERS

Item Part Number* Descrip on Qty

1 LYD3G-100A Front wheel assembly 2

2 1dap/welddaS001-K3DYL

3 1revoC3-J3DYL

4 LYD3G-200A Handle Assembly w/ foam 1

5 2gnirpSnruteR3-F2DYL

6 LYD2K.3 Power Unit Assembly 1

7 LYD3G-300 Handle Fork Assembly 1

8 LYD3F-103A Rear Caster Assembly 2

9 LUDBI-3T-17 Handle foam only 1

10 LYD3K-1 Saddle pad only 1

N/A ATD7331A-L 1lebaLtcudorP

* Items not ideŶƟĮed by part number are not available for replacement.

–ATD 7331AModel:

Capacity:3Ton

WARRANTY INFORMATION

ONE YEAR LIMITED WARRANTY

For a period of one (1) year from purchase date, ATD Tools, Inc. will repair or replace

without charge, (at it’s option) your ATD product, if it was purchased new and the product has failed

due to a defect in material or workmanship which you experienced during normal use of the product.

This limited warranty is your exclusive remedy.

To access the benefits of this warranty, contact an ATD Tools, Inc. supplier for confirmation

that this warranty applies. Thereafter, you may be advised to return the product under warranty,

freight prepaid, to the ATD service department.

If this ATD product is altered, abused, misused, modified, or undergoes service by an

unauthorized technician, the warranty will be void. We are not responsible for damage to

ornamental designs you place on this ATD product and such ornamentation should not cover

any warnings or instructions or they may void the warranty. This warranty does not cover

scratches, superficial dents, and other abrasions to the paint finish that occur under normal use.

Subject to the law in your state:

(1) Your sole and exclusive remedy is repair or replacement of the defective product as

described above.

(2) ATD is not liable for any incidental damages, including but not limited to, lost profits and

unforeseeable consequences.

(3) The repair and replacement of this product under the express limited warranty described

above is your exclusive remedy and is provided in lieu of all other warranties, express or

implied. All other warranties, including implied warranties and warranties of

merchantability or fitness for a particular purpose are disclaimed and, if disclaimer is

prohibited, these warranties are limited to one year from your date of purchase of this

product.

Some states’ laws do not allow limited durations on certain implied warranties and some states’

laws do not allow limitations on incidental or consequential damages. You should consult the

law in your state to determine how your rights may vary.

ATD Tools, Inc.

160 Enterprise Drive

Wentzville, MO 63385

Visit us at www.atdtools.com

Printed In China

–ATD 7331AModel:

Capacity:3Ton

PREVENTIVE MAINTENANCE RECORD LOG

Date Maintenance Performed

ATD 7331AModel:

Capacity:3Ton

–

Table des matières

Autres manuels ATD Tools Jack

ATD Tools

ATD Tools ATD-7317 Instructions d'utilisation

ATD Tools

ATD Tools ATD-7486B Manuel utilisateur

ATD Tools

ATD Tools 7436A Manuel utilisateur

ATD Tools

ATD Tools ATD-7447 Instructions d'utilisation

ATD Tools

ATD Tools ATD-7317 Manuel de service

ATD Tools

ATD Tools ATD-7461 Manuel utilisateur

ATD Tools

ATD Tools ATD-7431A Manuel utilisateur

ATD Tools

ATD Tools ATD-7237 Manuel utilisateur

ATD Tools

ATD Tools ATD-7383W Manuel utilisateur

ATD Tools

ATD Tools ATD-7465 Manuel utilisateur

ATD Tools

ATD Tools ATD-7344B Manuel utilisateur

ATD Tools

ATD Tools ATD-7304 Manuel utilisateur

ATD Tools

ATD Tools MagicLift ATD7325 Instructions d'utilisation

ATD Tools

ATD Tools 7435 Manuel utilisateur

ATD Tools

ATD Tools ATD-7462 Manuel utilisateur

ATD Tools

ATD Tools ATD-7227B Manuel utilisateur

ATD Tools

ATD Tools ATD-7465 Manuel utilisateur

ATD Tools

ATD Tools ATD-7384W Manuel utilisateur

ATD Tools

ATD Tools ATD-7354 Manuel utilisateur

ATD Tools

ATD Tools 7434A Manuel utilisateur

ATD Tools

ATD Tools ATD-7343 Manuel utilisateur

ATD Tools

ATD Tools 7425A Manuel utilisateur

ATD Tools

ATD Tools Atd-7432 Instructions d'utilisation

ATD Tools

ATD Tools ATD-2025 Manuel utilisateur

Manuels Jack populaires d'autres marques

Omega Lift Equipment

Omega Lift Equipment 18122C Instructions d'utilisation

Pittsburgh

Pittsburgh 58816 Instructions de montage

Unimec

Unimec TP Manuel utilisateur

Sonic

Sonic 4800703 Manuel utilisateur

BGS technic

BGS technic 70039 Manuel utilisateur

TradeQuip

TradeQuip 1128T Manuel utilisateur

VEVOR

VEVOR TJD-12000SP-F Manuel utilisateur

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Manuel utilisateur

Stels

Stels 51131 Manuel utilisateur

Bushranger

Bushranger RJX01 Manuel utilisateur

Clarke

Clarke CTJ2500QLG Manuel d'installation et d'exploitation

Valex

Valex 1650520 Manuel utilisateur

Pfaff

Pfaff Merkur M0 Manuel utilisateur

Beta

Beta 3050/K Supplément

Sealey

Sealey 1050CXHV Manuel utilisateur

Jung

Jung JH Series Manuel utilisateur

URIAH

URIAH UC200020 Manuel utilisateur

Kennedy

Kennedy KSJ010 Manuel utilisateur