AT&T E598-2 Manuel utilisateur

Quick start guide

E598-2

5.8 GHz expansion handset forhandset forforor

use with AT&T models E5901/E5901/

E5902B/E5903B/ E5911/E5911/

E5912B/E5913B/E5914B/

E5921/E5922B/E5923B/E5924B/

E6001/E6002B/E6012B/E6013B/

E6014B/E3813B

TONE

Getting started

Quick reference guide

Handset LEFT RIGHT

DOWN

CENTER

REDIAL/PAUSE

Press to view redial

memory. While entering

numbers, press and hold

to insert a dialing pause.

OFF/CLEAR

During a call, press to

hang up. While using

menus, press to cancel

an operation, back up to

the previous menu, or

exit the menu display.

TONE

DELETE PAUSE

MUTE REDIAL

MUTE/DELETE

While on a call, press to

mute microphone. While

reviewing the call log,

press to delete an indi-

vidual entry, or press and

hold to clear the caller

ID log. While predialing,

press to delete digits from

a string.

CID

Press to display caller

ID information.

SPEAKER

Press to activate hand-

set speakerphone. Press

again to resume normal

handset use.

DIR

Press to display directory

entries.

PHONE/FLASH

Press to make or

answer a call. During a

call, press to receive an

incoming call if call wait-

ing is activated.

INT

Press to initiate an inter-

com conversation or

transfer a call.

MENU/SELECT

Press to display the

menu. Once in the menu,

press to select an item

or save an entry or set-

ting. Press or to

scroll up or down while

in menus. While entering

names or numbers, press

or to move the cur-

sor to the left or right.

Getting started

Battery installation & charging

After battery installation, the battery may have enough charge to allow

for some calls. For best performance, place the handset in the charger

or telephone base and allow it to charge for 16 hours before use. You

can keep the battery charged by returning the handset to the charger or

the telephone base after each use. When the battery is fully depleted, a

recharge takes about 12 hours. The average talk time on a fully charged

battery is about eight hours depending on environmental conditions, and

the standby time when idle is approximately five days.

TONE

6. The battery

may have enough

charge to allow

for some calls. For

best performance,

place handset in

the telephone

base or charger

to charge for at

lease 16 hours

before first use.

Low battery indicator

Return handset to the

telephone base or char-

ger to recharge when

this symbol flashes.

(Handset will beep when

battery is low.)

3. Plug the battery

securely into the plug

inside the handset

battery compartment,

matching the color-

coded label.

To replace the battery, press

in and downward on the tab

to open the battery compart-

ment cover. Then lift out the

old battery and disconnect.

Follow the instructions on this

page to install and charge the

new battery.

5. Slide battery

compartment

cover towards

the center until

it clicks closed.

4. Place the

battery and

wires neatly

inside the com-

partment.

Caution: Use only the supplied rechargeable battery or AT&T replacement

battery model 27910 (part number 89-0099-00-00). To order, visit our website at

www.telephones.att.com or call 1 (800) 222-3111. In Canada dial 1 (866) 288-4268.

LOW BATTERY

1. Plug the small

end of the smaller

power adapter into

the jack on the

underside of char-

ger, then route the

cord through the

slot as shown.

2. Plug the

large end of

the smaller

power

adapter into

an electrical

outlet.

Getting started

Adding and registering handsets

Before using a new E598-2 handset, you must register it with

your E5901/E5902B/E5903B/E5911/E5912B/E5913B/E5914B/

E5921/E5922B/E5923B/E5924B/E6001/E6002B/E6012B/E6013B/

E3813B or E6014B telephone base (purchased separately). The

E5901/E5902B/E5903B/E5911/E5912B/E5913B/E5914B/E5921/

E5922B/E5923B/E5924B/E6001/E6002B/E6012B/E6013B/E3813BE6001/E6002B/E6012B/E6013B/E3813BE6012B/E6013B/E3813B

or E6014B can accommodate up to four cordless handsets.

The handset provided with the E5901/E5911/E5921 or E6001 isE6001 isis

automatically registered as handset 1. Additional handsets will

be assigned numbers in the order they are registered (handset 2,

handset 3 and handset 4). You can register a maximum of four

handsets.

The E5902B/E5912B/E5922B/E6002B or E6012B has two hand-

sets automatically registered as handset 1 and 2. You can register

two additional handsets, which will be assigned numbers 3 and 4.

The E5903B/E5913B/E5923B/E3813B or E6013B has three

handsets automatically registered as handsets 1, 2 and 3. You can

The E5904B/E5914/E5924B/E6014B has four pre-registered

handsets, so you cannot register any additional handsets to it.

Getting started

NOT REGISTERED

PRESS

HNDST LOC

4 SEC ON BASE

Adding and registering handsets

Before using a new E598-2 handset, you

must register it with the telephone base.

Each handset must be registered seper-

ately.

To register a handset to your telephone

base

When first purchased, the expansion hand-

set will show NOT REGISTERED on the

screen. The new handset may need to be

charged for five minutes before registering

to the main telephone base.

1. Place the unregistered handset into the

telephone base. If PRESS HNDST LOC 4

SEC ON BASE does not appear on the

handset screen after a few seconds, lift

up handset and place it in the telephone

base again.

2. On the telephone base, press and hold

HANDSET LOCATOR for about four

seconds (until the red IN USE light

on the telephone base turns on) and

then release the button. The handset

will show PLEASE WAIT…. and will

take about 10 seconds to complete

the registration. The handset will show

HS X REGISTERED and will beep if the

registration was successful.

NOTES:

1. If the registration was not successful the display

will show NOT REGISTERED. To reset the hand-

set, lift the handset out of the telephone base

or charger and replace it. Try the registration

process again.

2. You cannot register a handset if any phone con-

nected to your phone line is in use.

PLEASE WAIT...

HS X

REGISTERED

12:00PM

Getting started

Replacing a handset

You may need to de-register your handsets if:

You have the maximum number of registered handsets (four) and

you need to replace a handset.

-OR -

You wish to change the designated handset number of your reg-

istered handsets.

You must first de-register ALL the handsets, and then re-register

ALL the handsets you wish to use.

Please read carefully through all the instructions on this page

before beginning the de-registration process.

To de-register all handsets

1. Press and hold HANDSET LOCATOR on the telephone base

for about 10 seconds (until the IN USE light turns on and

starts to flash), then release the HANDSET LOCATOR button.

2. Immediately press and release HANDSET LOCATOR again.

You must press HANDSET LOCATOR while the IN USE light

is still flashing. (The light flashes for about seven seconds.)

3. The handset(s) will show CONNECTING... and it will take about

10 seconds to complete de-registration. ALL handsets will

show NOT REGISTERED if de-registration was successful.

4. To re-register the handset(s) to the telephone base, follow the

registration instructions on page 3-4.

NOTES:

1. If the de-registration process was not successful, you may need to reset the

system and try again. To reset: pick up any registered handset and press the

PHONE/FLASH button, then press the OFF/CLEAR button and place the

handset back into the base. You may also reset by unplugging the power from

the telephone base and plug it back in.

2. You cannot de-register the handset(s) if any phone connected to your phone

line is in use.

NOT REGISTERED

AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures,

licensed to Advanced American Telephones. Printed in China. Issue 2 03/07.

91-001110-010-100

www.telephones.att.com

Table des matières

Autres manuels AT&T Combiné

AT&T

AT&T TL30100 Manuel utilisateur

AT&T

AT&T TL90073 Manuel utilisateur

AT&T

AT&T TL86009 Manuel utilisateur

AT&T

AT&T BE50 Manuel utilisateur

AT&T

AT&T BL102-2S Manuel utilisateur

AT&T

AT&T E580-1 Manuel utilisateur

AT&T

AT&T CL80100 Manuel utilisateur

AT&T

AT&T SB67108 - AT&T Manuel utilisateur

AT&T

AT&T E252 Manuel utilisateur

AT&T

AT&T 2400 Manuel utilisateur

AT&T

AT&T E5640 Manuel utilisateur

AT&T

AT&T 2300 Manuel utilisateur

AT&T

AT&T SB67108 - AT&T Manuel utilisateur

AT&T

AT&T CL82219 Manuel utilisateur

AT&T

AT&T CL80111 Manuel utilisateur

AT&T

AT&T CL80113 Manuel utilisateur

AT&T

AT&T 2402 Manuel utilisateur

AT&T

AT&T Synapse SB67040 Manuel utilisateur

AT&T

AT&T CL82214 Manuel utilisateur

AT&T

AT&T SL80108 Manuel utilisateur

AT&T

AT&T EP562 Manuel utilisateur

AT&T

AT&T CL82107 Manuel utilisateur

AT&T

AT&T SB67108 - AT&T Manuel utilisateur

AT&T

AT&T CLP99003 Manuel utilisateur

Manuels Combiné populaires d'autres marques

Swissvoice

Swissvoice ePure HD Manuel utilisateur

Philips

Philips TD6736/BH051P Manuel utilisateur

ASCOM

ASCOM I62 - Manuel utilisateur

LG-Ericsson

LG-Ericsson LIP-9010 Manuel utilisateur

GE 1583 Manuel utilisateur

iiNet

iiNet Handset Manuel utilisateur

ASCOM

ASCOM 9p23 Manuel utilisateur

AirCell

AirCell ST 3100 Manuel utilisateur

Eaton

Eaton HHIR-LCD-PROG Instructions de montage

Mitel

Mitel 112 Manuel utilisateur

SBC

SBC SBC-381H Manuel utilisateur

Mitel

Mitel 5602 Manuel utilisateur

ASCOM

ASCOM d81 Messenger Instructions d'installation

SpectraLink

SpectraLink 7522 Manuel utilisateur

Avaya

Avaya L100 Series Comment utiliser

ooma

ooma HD2 Handset Manuel utilisateur

Yealink

Yealink IPW56 Manuel utilisateur

Sony

Sony SBH52 Manuel utilisateur