AON INNI Manuel utilisateur

INNI_USER MANUAL_191225PS

User Manual

BIO-CERAMIC DLP 3D PRINTER

DENTAL

Chapter 1 Safety Precautions 3

Chapter 2 Introduction to INNI 3D Printer (ACP-M11Y) 4~8

What is INNI 3D Printer? 4

Special features 5

List of components 6~7

Additional products 8

Chapter 3 INNI 3D Printer Usage Guide 9~23

Setting Up the Printer 10~13

Setting Up the Network 14~15

Using the Slicer Program 16~17

Using the Touch Screen Functions 18~23

Software & Firmware Updates 23

Chapter 4 Troubleshooting 24

Chapter 5 Product Specifications 25

Chapter 6 Product Warranty 26~27

TABLE OF

CONTENTS

INNI_USER MANUAL_191225PS

※ Please follow safety instructions at all times.

Read the following precautions carefully and familiarize yourself with the INNI 3D Printer User Manual

before setting up and using the printer. Failure to comply with the given warnings can lead to serious injury,

fire, or equipment and/or property damage.

•Make sure that the printer and all accessories are physically intact and free of damage.

•Do not destroy or alter the printer’s power cable. Use the proper voltage (220V) when connecting to a power source.

•Parts of the printer have sharp edges/corners. Be careful to avoid injury or printer damage when using.

•Do not place a foreign object inside the printer as this will incur the risk of injury or property damage.

•Select the installation site carefully to avoid causing injury to children or pets.

•Avoid operating the printer with wet or dirty hands as the introduction of water or other foreign liquid to the printer’s metal

and other conductive surfaces can cause fire or electric shock.

•Do not install the printer outdoors or in an area that is poorly ventilated, humid, or dusty.

•Do not disassemble or alter the printer except as specified in the operation manual since doing so may cause user injury

and/or printer damage. Any such problem will not be covered under warranty.

1. Safety Precautions

2. Introduction to INNI 3D Printer

2. Introduction to INNI 3D Printer (ACP-M11Y)

INNI 3D Printer is especially designed to produce artificial teeth.

Using INNI-CERA (BCM-W500), a zirconia slurry designed exclusively for INNI 3D Printer, and digital

light processing, any dental configuration can be recreated before your very eyes, one layer at a time.

A 7-inch color touch screen is provided at the front of the printer for easier use.

Smart, comfortable design

What is INNI 3D Printer ?

INNI_USER MANUAL_191225PS

One star feature of INNI 3D Printer is its automatic bed leveling function,

which allows for hassle-free operation and precision.

Automatic leveling function

Special features

Another key feature of INNI 3D Printer is the special modeling bed film that makes up the base of the modeling bed.

Detachable and reversible, it allows for optimized light refraction to achieve higher durability in the printed output and

is designed to release the finished product cleanly and easily.

3D Modeling Bed Film

* For film exchange or modeling bed installation,

please refer to the video. www.aoninni.com

Modeling bed

Modeling bed film

Modeling bed

bracket

Bracket bolts

Build platform

Liquid zirconia material designed to be used exclusively by INNI 3D Printer

* Important note : For the shrinkage percentage, please refer to the label

on the bottle.

Zirconia slurry (BCM-W500)

2. Introduction to INNI 3D Printer

NO Name Description

1LCD console LCD touch screen panel

2Power button Power switch next to the LCD console

3Main door Outward swinging door; blocks UV rays during printing

4USB ports Connection for a USB memory stick or external hard drive

5Ethernet port Connection for a computer (recommended)

6Main power switch Main switch for the power source to the printer

7Power socket 220V connection socket

8Handle Used for lifting and moving the printer

9Air vents Ventilation openings

10 Main door panel For viewing the printing process

Outer components

③

Main door

①

LCD console

⑩

Main door panel

⑨

Air vents

⑦

Power socket

⑥

Main power

switch

⑤

Ethernet port

⑧

Handle

②

Power button

④

USB ports

List of components

INNI_USER MANUAL_191225PS

NO Name Description

1LM GUIDE Guide for the z-axis stage

2Knob-L30 Fixture for the build platform

3Blade support Attachment support for the mixing blade

4Knob-Blade Fixture for the mixing blade

5Blade For the mixing the slurry inside the modeling bed

6Modeling bed Container for the slurry

7VR15 Leveler for the printer

8Knob-L15 Fixture for the platform plate

9Ball screw Controller for the z-axis stage

10 Z-axis main stage arm Attachment support for the build platform using Knob-L30

11 Z-axis stage Connecting stage between the LM guides and ball screw

12 Knob-L20 Fixture for the modeling bed

Internal components

①LM GUIDE

② Knob-L30

⑦ VR15

⑥ Modeling bed

⑤ Blade

④ Knob-Blade

③ Blade support

⑧ Knob-L15

⑨ Ball screw

⑩ Z-axis main

stage arm

⑪ Z-axis stage

⑫ Knob-L20

Item Product code Item Product code

Scraper

Used to detach the

printed output

AS11-1001P Modeling bed lm

(10 total) AS11-1001P

BCM-W500

Zirconia slurry for

INNI 3D Printer use

ACP11-10001Y Power cable

Main power cord ACP11-10001Y

Build platform AB11-40000A

Ethernet cable

Used to connect

a computer

to INNI 3D Printer

AB11-40000A

Item Item

Safety glasses

Protection for the eyes

Hex key (2.5mm)

Used to change

the modeling bed film

Latex gloves

Protection for the hands

Sprayer

Used to clean the build

platform/modeling bed

Spatula

Used for mixing

Hex key (3.0mm)

Used to attach/detach

the main door of the printer

Nipper

Used to remove

the support on the printed output

Sieve

Used to filter out residue

* To purchase, please contact AON Call Center at (+82 70 4304 4996).

The following is a list of the accessories included with product purchase. This list is subject to change without notice.

See homepage (http://www.aoninni.com) for additional purchase options.

Additional products (included)

The following is a list of the extra accessories available for INNI 3D Printer.

Accessories (for purchase)

2. Introduction to INNI 3D Printer

2.5mm

3.0mm

Additional Products

INNI_USER MANUAL_191225PS

3. INNI 3D Printer Usage Guide

1) Please install the printer in a climate controlled environment (15-35°C) without exposure to water or direct sunlight.

Be sure to use the proper voltage (220V) and to flip the main power switch on the backside of the printer to the

ON position.

2) Locate the power button next to the LCD console on the front of the printer. Push this button for one or more

seconds until a click is heard. The touch screen panel will display AON’s logo upon start up.

Note: INNI 3D Printer is only compatible with Windows 7 or higher.

3) An exclusive zirconia slurry (BCM-W500) is used for the inlays, crowns, bridges, etc. created by INNI 3D Printer.

To input dental configurations for printing, upload the printing file from a computer that is connected via Wi-Fi/

Ethernet or from an external memory stick/drive via USB.

Note: To create or edit a printing file, you must use AON slicer software.

4) Set the layer thickness to 50μm and the curing conditions to 15 seconds.

5) Add the zirconia slurry (BCM-W500) into the INNI 3D Printer modeling bed and implement Preheat and Blade

Mixing before printing.

6) The build platform will lower, automatically adjusting to the correct height, and the 3D printing process will begin.

Layers (displayed as an image on the touch screen) are laminated one at a time and cured via UV LED light. This

laminating and curing process repeats until the dental restoration shape specified for printing has been created.

7) The printed output should detach easily from the base of platform plate. Remove the supports attached underneath

and finish it off with a cleaning and final heat treatment.

8) Printed restorations created by INNI 3D Printer are to be used as artificial dental or other prostheses for natural

teeth.

9) INNI 3D Printer must use AON’s exclusive zirconia slurry INNI-CERA to produce the desired dental restorations.

Using other products will cause damage to the printer in which case AON cannot be held responsible.

* Please refer to the video on our website for more details.

* If you have further questions, contact our Call Center (+82 70 4304 4996) or send a message to our Support

Team (www.aoninni.com).

User Guidelines

3. INNI 3D Printer Usage Guide

Confirm that the bottle of zirconia slurry is labeled BCM-W500.

1) Confirm that the printer looks intact and ready for use.

2) Open the bottle of zirconia slurry (BCM-W500) and check the contents for impurities.

Precautions

Pre-check before printing

① KNOB-L30

④ Blade

④ -1 KNOB-Blade

③-1 KNOB-L20

Platform plate

①-1 Z-AXIS MAIN

STAGE ARM

② KNOB-L15

③ Modeling bed

1. Install printing components

1) Build platform

Loosen the top fixture ①and attach the build platform to the platform holder ①-1.

2) Middle fixture (②KNOB-L15)

Loosen and check for suitable spring strength and operation.

(Two full turns should allow the platform plate to move easily in all directions).

* This is an important step prior to preheating or blade mixing.

3) Modeling Bed : Attach to the printer using the modeling bed fixtures ③-1

4) Blade : Attach to the printer using the blade fixture ④-1.

2. Prepare printing - Zirconia slurry (BCM-W500)

1) Pour 150g of the slurry into the modeling bed.

2) Preheat : AON Slicer →Set up →Position control →Preheat (10/20/30mins)

* When preheat, a light will turn on inside the printer on the left side.

* During the preheating process, do not use any other printer operation

3) Blade mixing : AON Slicer →Set up →Position control →Blade mixing

4) Touch screen of printer →Position control →Home position →Tighten the middle fixture (②KNOB-L15) →

Plates →Start print

* Make sure that the middle fixture (②KNOB-L15) is tightened before printing.

* Please refer to the video on our website for more details. www.aoninni.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AON Imprimante 3D

AON

AON Inni-Robo Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur