Antec P183 Manuel utilisateur

P183

SER

’

ANUAL

ABLE OF

ONTENTS

NTRODUCTION

1.1 Case Specifications.…..………………………………………………………………………………….. 3

1. Diagram…………………………………………………………………….…………………………………. 3

ARDWARE

NSTALLATION

UIDE

.1 Setting Up….…………………………………………………………………………………………………. 4

. Power Supply Installation……………………………………………………………………………… 4

.3 CP Series Power Supply Mount..…………………………………………………………………… 5

.4 Cable Management………………………………………………………………………………………. 5

.5 Motherboard Installation..……………………………………………………………………………. 5

.6 Internal 3.5” Device Installation……………………………………………………………………. 6

.7 External 3.5” Device Installation…………………………………………………………………… 7

.8 External 5. 5” Device Installation…………………………………………………………………. 7

ONNECTING THE

RONT

I/O

ORTS

3.1 USB .0 Ports………………………………………………….……………………………………………. 8

3. eSATA Ports…………………………………….……………………………………………………………. 8

3.3 AC’97 / HD Audio Ports……………………….………………………………………………………… 8

3.4 Switch and LED Connectors…………………………………………………………………………… 9

3.5 Rewiring Motherboard Header Connections………………………………………………… 9

OOLING

YSTEM

4.1 TriCool™ Fans ………………………………………………………………………………………………. 10

4. Optional Fans.………………………………………………………………………………………………. 11

4.3 Washable Air Filters………………………………………..……………………………………………. 11

P183

SER

’

ANUAL

Antec,

continually

refine

and

improve

our

products

ensure

the

highest

quality.

It’s

possible

that

your

new

case

will

differ

slightly

from

the

descriptions in

this

manual. This

isn’t

problem;

it’s

simply

improvement.

the

date

publication,

all

features,

descriptions,

and

illustrations

this

manual

are

correct.

Dis

laim

d on

c’

lli

nd p

’

pon

The P183 does not come with a power supply (PSU). Make sure you choose a power

supply that is compatible with your computer components and has a long enough power

harness to reach your motherboard and peripheral devices. We recommend our CP

series, TruePower or Signature Series power supplies for the latest ATX specification

compliance, broad compatibility, and energy-saving capability.

Although care has been taken to prevent sharp edges in your Antec case, we strongly

recommend taking the appropriate time and care when working with it. Avoid hurried

or careless motions. Please use reasonable precaution.

This manual is

not

designed to cover CPU, RAM, or expansion card installation. Please

consult the motherboard manual for specific mounting instructions and troubleshooting.

Before proceeding

, check the manual for your CPU cooler to find out if there are steps you must

take before installing the motherboard. While installing hardware, keep your case on a flat,

stable surface.

1.1 C

ASE

PECIFICATIONS

Case Type

Advanced Mid Tower

Color

Gunmetal Gray

Dimensions

514mm (H) x 05mm (W) x 507mm (D)

0.3”(H) x 8.1”(W) x 19.9”(D)

Weight

31 lbs / 14 kg

Cooling

1 x Rear 1 0mm TriCool

™

1 x Top 1 0mm TriCool™ fan

1 x Lower chamber 1 0mm TriCool™ fan (optional)

1 x Front 1 0mm fan mount (optional)

1 x Middle 1 0mm fan mount (optional)

Drive Bays

11 Drive Bays:

4 x External 5. 5” drive bays

1 x External 3.5” drive bay

6 x Internal 3.5” drive bays

Expansion Slots 7

Motherboard Size

Mini-ITX, microATX, Standard ATX

Front I/O Panel

x USB .0

1 x eSATA

AC’97 / HD Audio In and Out

IAGRAM

1 0mm rear TriCool™ fan

1 0mm top TriCool™ fan

Washable air filters

Motherboard mount

Power supply mount

5. 5” drive bays

3.5” drive bays

Front I/O panel

ARDWARE

NSTALLATION

UIDE

ETTING

Place the case upright on a flat, stable

surface with the rear of the case facing

you.

. Remove the thumbscrews from the right

side panel. Grip the panel at the top and

bottom and slide it toward you to open

the case.

3. Remove the screws from the left side

panel. Grip the panel at the top and

bottom and slide it toward you to

remove the left side panel.

Note

: Do not use your fingernails to pry or lift

the panels.

OWER

UPPLY

NSTALLATION

1. Between the two chambers there is a plastic structure that lets

you run the cables to the upper and lower chambers. It is a

two-piece structure – one large and one small. Both pieces can

slide back and forth to adjust the openings.

. Loosen the two thumbscrews holding the plastic structure.

Slide the large piece all the way to the rear of the case to fully

extend the opening. Take any cables that will not be routed

through the cable management chamber and carefully guide

them through the openings to the upper chamber.

3. Fasten the power supply to the back of the case with the

screws provided.

4. Slide the small plastic piece to the rear of the case to fully

extend the other opening.

6. Slide both the large and small plastic pieces all the way to the

front of the case to close the openings when finished with the

hard drive installation.

7. Tighten the two thumbscrews on the plastic structure.

ERIES

OWER

UPPLY

OUNT

Your Antec P183 enclosure comes with a power supply mounting

adapter to mount either a standard-size power supply or Antec's

exclusive CP Series high-performance power supply. This adapter is

mounted to the chassis with standard Phillips-head screws. In order

to install a CP Series power supply, remove the mounting plate first.

ABLE

ANAGEMENT

There is a cable management compartment between the motherboard and right side panel. You can

tuck or route excess cables in this compartment.

Remove both side panels.

. Choose the cables you would like to pass through the holes behind the motherboard tray and pull

them out of the power supply chamber toward the right side of the case.

3. Use the cable ties provided to hold them in place.

4. Feed the cables back through the insertion point nearest the destination of the cable. Connect the

cable and then pull the slack back to the right side of the case.

OTHERBOARD

NSTALLATION

1. Lay the case down, with the open side facing up.

The drive cages and power supply should be visible.

. Make sure you have the correct I/O panel for your

motherboard. If the panel provided with the case

isn’t suitable, please contact your motherboard

manufacturer for the correct I/O panel.

3. Align your motherboard with the standoff holes and

remember which holes are lined up. Not all

motherboards will match with all the provided

holes; this is normal and won’t affect its

functionality.

4. Remove your motherboard by lifting it up.

5. Install standoffs as needed and put the

motherboard back in.

6. Screw in your motherboard to the standoffs with

the provided Phillips-head screws.

NTERNAL

3.5”

EVICE

NSTALLATION

With the front bezel facing you, swing the front door open. It can swing 70º so the door will be parallel

with the side of the case. You can see there are four 5. 5” and one 3.5” external drive bays. Inside the

case there are two 3.5” drive cages, which can house up to six hard drives.

Note

: We recommend using the lower HDD cage to maximize cooling and quiet computing.

Upper HDD Installation

1. Remove the thumbscrew holding the upper HDD cage.

. Remove the HDD cage from its position by pulling the ring toward you.

3. There are two HDD trays inside the cage. Squeeze the metal clips on each side of the tray and slide

the tray out.

4. Mount your hard drive into the drive tray with the special screws provided. Don’t over-tighten the

screws as this will reduce the vibration and noise dampening ability of the silicone grommets.

Note

: Always mount the HDD with the thicker side of the silicone grommets facing up.

5. Slide and lock the tray back into the cage.

6. Slide the cage back into the case and fasten the thumbscrew.

7. Find the right Molex or SATA connector on the power supply and connect it to the hard drive.

8. Repeat the same procedure for the other drives.

Lower HDD Installation

1. Remove the thumbscrew holding the lower HDD cage.

. Remove the HDD cage from its position by pulling the ring

toward you.

3. You can mount four hard drives inside the cage. They are

mounted vertically with the silicone grommets sitting at

both sides.

4. Mount your hard drive into the drive cage with the special

screws provided. Don’t over-tighten the screws as this will

reduce the vibration and noise dampening ability of the

silicone grommets.

Note

: Always mount the HDD with the thicker side of the

silicone grommets facing up.

5. Slide the cage back into the case and fasten the

thumbscrew.

6. Find the right Molex or SATA connector on the power

supply and connect it to the hard drive.

7. Repeat the same procedure for the other drives.

XTERNAL

3.5”

EVICE

NSTALLATION

There is one external 3.5” drive bay.

1. Carefully remove the plastic drive bay cover and metal plate covering the drive bay.

. Find a pair of 3.5”drive rails in the included hardware kit box.

3. Mount the drive rails onto the sides of the 3.5” device. Make sure the metal portion is angled on

the outside and facing forward.

4. Slide the device into the drive bay until it clicks into place.

5. Connect a small 4-pin connector from the power supply to the 4-pin connector on the floppy drive.

XTERNAL

5. 5”

EVICE

NSTALLATION

There are four 5. 5” drive bays that need a total of eight drive

rails.

1. Carefully remove the drive bay cover/filter assembly by

pressing the two tabs inward, then remove the metal plate

covering the drive bay.

. Mount the drive rails onto the sides of the 5. 5” device.

Make sure the metal tab is angled away from the drive.

3. Slide the device into the drive bay until it clicks into place.

4. Mount the other devices accordingly.

5. Connect the appropriate Molex or SATA connector from the

PSU to the power connector on each of the devices.

Signal

Names

Signal

Names

USB

Power

USB

Power

Negative

Signal

Negative

Signal

Positive

Signal

Positive

Signal

Ground

Key

(No

Connection)

Empty

Signal

Names

(HDA)

Signal

Names

(AC’97)

MIC2

MIC In

AGND

GND

MIC2

MIC Power

AVCC

FRO-R

Line

Out

(R)

MIC2_JD

Line

Out

(R)

F_IO_SEN

Key (no pin)

FRO-L

Line

Out

(L)

LINE2_JD

Line

Out

(L)

ONNECTING THE

RONT

I/O

ORTS

3.1

USB

Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check

the motherboard manual to ensure that it matches the table below:

SATA

You will find a SATA connector on a cable attached to the front ports. This internal SATA

connector is designed to connect to a standard SATA connector on your motherboard. This

will allow high-speed external hard disk enclosures such as the Antec MX-1 to run at the

same speeds as internally installed hard disks.

3.3

AC’97

UDIO

ORTS

There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High

Definition Audio) connector linked to the front panel of the case.

You can connect either the AC’97 or the HDA connector, depending on your motherboard.

Locate the internal audio connectors from your motherboard or sound card and connect

the corresponding audio cable. Consult your motherboard or sound card manual for the

pin-out positions. Even if your system supports both standards, only use one connector.

9 10

3.4

OWER

WITCH

ESET

WITCH

ARD

ISK

RIVE

LED

ONNECTORS

Connected to your front panel are LED and switch leads for power,

reset, and HDD LED activity. Attach these to the corresponding

connectors on your motherboard. Consult your motherboard

manual for specific pin header locations. For LEDs, colored wires

are positive ( + ). White or black wires are negative ( – ). If the LED

does not light up when the system is powered on, try reversing the

connection. For more information on connecting LEDs to your

motherboard, see your motherboard manual.

Note

: Polarity (positive and negative) does not matter for

switches.

3.5

EWIRING

OTHERBOARD

EADER

ONNECTIONS

There may come a time when you need to reconfigure the pin-out of a motherboard header connector.

Examples could be for your USB header, audio input header, or some other front panel connector such

as the Power Button connector.

Before performing any work, please refer to your motherboard manual or your motherboard

manufacturer's website to be sure of the pin-out needed for your connector. And we strongly

recommend making a notated drawing before beginning work so that you can recover if your work gets

disturbed.

Determine which wires you need to remove in order to rewire your

plug to match the USB pin-outs on your motherboard (refer to your

motherboard user’s manual). Working on one connector at a time,

use a very small flathead screwdriver or similar tool to lift up on

the black tab located beside the gold posts (squares). This will

allow you to easily slide out the pins from the USB plug.

Working carefully so as not to damage the wires, connectors, or

pins, slowly remove the pin from the connector. Repeat these

steps for each wire you need to change.

Working carefully so as not to damage the wires, connectors or

pins, slowly reinsert the pin into the correct slot of the connector

then snap closed the black tab that was lifted in step 1. Repeat

these steps for each wire you need to change.

Autres manuels pour P183

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Antec Enceinte

Antec

Antec P160 Manuel utilisateur

Antec

Antec NSK6500 Manuel utilisateur

Antec

Antec 902 Manuel utilisateur

Antec

Antec Veris Fusion Remote Max Guide de démarrage rapide

Antec

Antec Veris Fusion Remote Black Guide de démarrage rapide

Antec

Antec Veris Fusion Remote Black Manuel utilisateur

Antec

Antec P190 Manuel utilisateur

Antec

Antec Performance TX635 Manuel utilisateur

Antec

Antec Veris Fusion Remote Max Manuel utilisateur

Antec

Antec Plus800 Series Manuel utilisateur

Antec

Antec Solution SLK3700AMB User’s Manuel utilisateur

Antec

Antec OVERTURE II Manuel utilisateur

Antec

Antec Nine Hundred Two Manuel utilisateur

Antec

Antec Veris Fusion 430 Guide de l'utilisateur

Antec

Antec Sonata Designer UCC13# 0761345-08146-7 EC Manuel utilisateur

Antec

Antec Solution SLK3700AMB Manuel utilisateur

Antec

Antec Fusion Remote Max Manuel utilisateur

Antec

Antec KS-288 Manuel utilisateur

Antec

Antec MINUET 300 Manuel utilisateur

Antec

Antec VSK-2450 Manuel utilisateur

Antec

Antec Sonata Designer 500 Manuel utilisateur

Antec

Antec Solution SLK2600AMB User’s Manuel utilisateur

Antec

Antec VSK-1000 Manuel utilisateur

Antec

Antec BK640B Manuel utilisateur

Manuels Enceinte populaires d'autres marques

SilentiumPC

SilentiumPC Armis AR5 Manuel

Pulsar

Pulsar 17/TRP80/DSPR Manuel utilisateur

Thermaltake

Thermaltake V150 TG Manuel utilisateur

MSI

MSI MPG SEKIRA 500X Manuel utilisateur

Nexans

Nexans WTC05 Manuel utilisateur

Peavey

Peavey DS 1502 Manuel utilisateur

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manuel utilisateur

Rosewill

Rosewill RX82-U(JBOD) Manuel utilisateur

QNAP

QNAP SAS JBOD CLI 1.0 Manuel utilisateur

GAMDIAS

GAMDIAS Talos P1 Manuel utilisateur

Auvs

Auvs KR615 Manuel utilisateur

Digitus

Digitus DA-71114 Manuel utilisateur

CommScope

CommScope FDH 3000 Manuel utilisateur

FS FHD-FWME4 Manuel utilisateur

JBL

JBL CS1215T Manuel utilisateur

Pulsar

Pulsar ARAD-S4 Manuel utilisateur

Pulsar

Pulsar AWO454 Manuel utilisateur

NewerTech

NewerTech Voyager S3 Manuel utilisateur