Antari FT-50 Manuel utilisateur
FT-50 Fire Training
Fog Machine User Manual
ENGLISH
©2017 Antari Lighting and Effects Ltd.
3
User Manual - English
Safety Information
Please read the following safety information carefully before operating the
machine. This information includes important safeguards about installation,
usage, and maintenance. Pay attention to all warning labels and instructions in
this manual and printed on the machine.
If you have questions about how to operate the machine safely, please contact your local
Antari dealer for help.
․Keep this device dry.
․Always connect to a grounded circuit to avoid risk of electrocution.
․Before connecting machine to power, always check voltage indicate on machine match
to your local AC voltage. Do not use the machine if AC power voltage does not match.
․Disconnect the machine from AC power before servicing and when not in use.
․This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled,
disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts,
immediately unplug the machine and contact your local Antari dealer for advice.
․No user serviceable and modifiable parts inside. Never try to repair this product, an
unauthorized technician may cause damage or malfunction to the machine.
․For adult use only. Never leave the machine running unattended.
․Installed the machine in a well-ventilated area. Provide at least 50 cm space around the
machine.
․Never add flammable liquid of any kind to the machine.
․Make sure there are no flammable materials close to the machine while operating.
․Only use Antari aerosols. Other aerosols may lead to heater clog and malfunction.
․Remove aerosols after use.
․If the machine fails to work, unplug the machine and stop operation immediately.
4
Contact your localAntari dealer for advise.
․Before transporting the machine, make sure the aerosols is removed
․Fog fluid may present health risks if swallowed. Do not drink fog fluid. Store it securely.
In case of eye contact or if fluid is swallowed, immediately look for medical advice.
Unpacking and Inspection
Immediately upon receiving the machine, carefully unpack the carton, check the content to
ensure that all parts are present and have been received in good condition. If any parts
appear damaged or mishandled from shipping, notify the shipper immediately and retrain the
packing material for inspection.
What is included: 1 x FT-50 Fog Machine
1 x Power Cord
1 x User Manual
Product Dimensions
346 mm
251 mm
152 mm
5
Product Overview
Operation
Step 1: Place the machine on a flat surface and in a suitable large area with at least 50 cm
open space around the machine.
Step 2: Check and cleared any foreign object in the threaded aerosol insert. Align aerosol
valve with threaded insert and carefully turn clockwise to fix into positiion. Aerosol should be
screwed in tightly to create an effective seal
=
Volume Control Knob
Power Switch
LED Indicator
Breaker
Power Input
Aerosol Compartment
6
Step 3: Connect the machine to suitable rated power supply. To determine the power
requirement for the machine refer to the label on the back of the machine.
Always connect the machine to a protected circuit and ensure it is properly
grounded to avoid risk of electrocution.
Step 4: Turn on the machine and allow it to heat up. Heat up takes approximatly 7.5 mintues.
Once the machine has reached operating temperature, the LED inidcator located in back
panel will turn solid green. Now the machine is ready for operation.
Step 5: To start making fog, press and hold the push button on handle bar, release to stop.
Step 6: To adjust output volume, rotate the knob located in back panel. Turn
counter-clockwise to increase, clockwise to decrease.
Step 7: To turn off the machine, flip the power switch to OFF position. Remove aerosol and
power cord.
Off Power Operation
FT-50 can be operating off mains power once it has reached working temperature. The
amount of smoke can be produced depends on its temperature cycle when it is
disconnected. With a complete heating cycle the machine can still generate smoke up to 45
minutes after disconnection.
The quality of fog must be carefully observed while operating off mains power. When smoke
has become thin and blue indicates the temperature is getting low. Reconnect machine to
mains power for heating process, once it reached working temperature it can be operate off
power again.
7
Aerosols
Only use Antari FLP-700 aerosol for the FT-50 Fire Training Fog
Machine.
The machine is tested and calibrated with this aerosol to get the
best output performance. Warranty will be void if any other type
of aerosol is used, improper use of aerosol may lead to
machine failure and malfunction.
Service and Maintenance
․Do not allow the machine to become contaminated.
․Remove dust from air vents with air compressor, vacuum or a soft brush.
․Only use a damp cloth to clean the casing.
․Before storing run distilled water through the system to help avoid condensing the pump
or heater.
․It is recommended to run the machine on a monthly basis in order to achieve best
performance and output condition.
․Excessive dust, liquid and dirt built up will degrade performance and cause overheating.
Breaker Reset
Disconnect AC power before resetting the breaker. Only replace fuse with same
type and rating.
Step 1: Disconnect AC power.
Step 2: Flip breaker to ON position.
Step 3: Turn on machine for testing.
8
Breaker
120V = 15A 250V
230V = 8A 250V
Technical Specifications
Input voltage US 120V EU 230V
UK 240V JP 100V
Breaker 120V = 15A 250V
230V = 8A 250V
Heater 1450W
Warm-up time 7.5 min. (approx.)
Fluid consumption 110 ml/min
Compatible fluid Antari FLP aerosol
Power connection IEC
Dimension L 346 x W 152 x H 251 mm
Dry weight 9.8 kg
Autres manuels pour FT-50
1
Table des matières
Autres manuels Antari Machine à brouillard
Antari
Antari S-100 II Manuel utilisateur
Antari
Antari FT-100 Fire Training Manuel utilisateur
Antari
Antari FT-100 Fire Training Manuel utilisateur
Antari
Antari Z-1520 RGB Manuel utilisateur
Antari
Antari LCU-1 Manuel utilisateur
Antari
Antari X FAZER Manuel utilisateur
Antari
Antari Z-1200II Manuel utilisateur
Antari
Antari FT-200 Manuel utilisateur
Antari
Antari Z-350 FAZER Manuel utilisateur
Antari
Antari S-120 Manuel utilisateur
Antari
Antari MOBILE MB-1 Manuel utilisateur
Antari
Antari F-4D Fazer Manuel utilisateur
Antari
Antari DNG-250 Manuel utilisateur
Antari
Antari Z-1500II Manuel utilisateur
Antari
Antari Z-1200 III Manuel utilisateur
Antari
Antari M-11 Manuel utilisateur
Antari
Antari W-715 Fog Jet Manuel utilisateur
Antari
Antari X-310PRO Manuel utilisateur
Antari
Antari M-8 Manuel utilisateur
Antari
Antari F-450 Manuel utilisateur
Manuels Machine à brouillard populaires d'autres marques
Boost
Boost BOOST-FOG400LED-BK Manuel utilisateur
Home Accents Holiday
Home Accents Holiday FM1000-ASH Manuel utilisateur
EuroLite
EuroLite ZEITGEIST FOG-1200 Manuel utilisateur
Dyna-Fog
Dyna-Fog CYCLONE ULTRA 2734 Manuel utilisateur
PROEL
PROEL DRAGO HEAVY PLFD150HY Manuel utilisateur
Sparklyn
Sparklyn Y846 Manuel utilisateur
