Anritsu MT8852B Manuel utilisateur

MT8852B

Operation Manual

Bluetooth Test Set

Operation Manual

MT8852B

Bluetooth Test Set

P/N: 13000-00205

Revision: N

Printed: February 2017

Safety-2

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu

Corporation uses the following safety symbols to indicate safety-related information. Ensure

that you clearly understand the meanings of the symbols BEFORE using the equipment.

Some or all of the following symbols may be used on all Anritsu equipment. In addition, there

may be other labels attached to products that are not shown in the diagrams in this manual.

Symbols Used in Manuals

Safety Symbols Used on Equipment and in Manuals

The following safety symbols are used inside or on the equipment near operation locations to

provide information about safety items and operation precautions. Ensure that you clearly

understand the meanings of the symbols and take the necessary precautions BEFORE using

the equipment.

This indicates a very dangerous procedure that could

result in serious injury or death if not performed properly.

This indicates a hazardous procedure that could result in

serious injury or death if not performed properly.

This indicates a hazardous procedure or danger that could

result in light-to-severe injury, or loss related to equipment

malfunction, if proper precautions are not taken.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates a compulsory safety precaution. The required operation is indicated

symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

DANGER

WARNING

CAUTION

Safety-3

For Safety

Warning

•ALWAYS refer to the operation manual when working near

locations at which the alert mark shown on the left is attached. If

the advice in the operation manual is not followed, there is a risk

of personal injury or reduced equipment performance. The alert

mark shown on the left may also be used with other marks and

descriptions to indicate other dangers.

•Overvoltage Category

This equipment complies with overvoltage category II defined in

IEC 61010. DO NOT connect this equipment to the power supply

of overvoltage category III or IV.

Warning

When supplying power to this equipment, connect the accessory 3-

pin power cord to a 3-pin grounded power outlet. If a grounded 3-pin

outlet is not available, use a conversion adapter and ground the

green wire, or connect the frame ground on the rear panel of the

equipment to ground. If power is supplied without grounding the

equipment, there is a risk of receiving a severe or fatal electric shock.

Warning Only qualified service personnel with a knowledge of electrical fire

and shock hazards should service this equipment. This equipment

cannot be repaired by the operator. DO NOT attempt to remove the

equipment covers or unit covers or to disassemble internal

components. There are high-voltage parts in this equipment

presenting a risk of severe injury or fatal electric shock to untrained

personnel. In addition, there is a risk of damage to precision

components.

Warning The performance-guarantee seal verifies the integrity of the

equipment. To ensure the continued integrity of the equipment, only

Anritsu service personnel, or service personnel of an Anritsu sales

representative, should break this seal to repair or calibrate the

equipment. Be careful not to break the seal by opening the equipment

or unit covers. If the performance-guarantee seal is broken by you or

a third party, the performance of the equipment cannot be

guaranteed.

Caution

Never input a signal of more than the indicated value between the

measured terminal and ground. Input of an excessive signal may

damage the equipment.

Safety-4

Caution

Electrostatic Discharge (ESD) can damage the highly sensitive

circuits in the instrument. ESD is most likely to occur as test devices

are being connected to, or disconnected from, the instrument’s front

and rear panel ports and connectors. You can protect the instrument

and test devices by wearing a static-discharge wristband.

Alternatively, you can ground yourself to discharge any static charge

by touching the outer chassis of the grounded instrument before

touching the instrument’s front and rear panel ports and connectors.

Avoid touching the test port center conductors unless you are

properly grounded and have eliminated the possibility of static

discharge.

Repair of damage that is found to be caused by electrostatic

discharge is not covered under warranty.

Safety-5

WARRANTY

The Anritsu Corporation will repair this equipment free-of-charge if a malfunction

occurs within one year after shipment due to a manufacturing fault. However, software

fixes will be made in accordance with the separate Software End-User License

Agreement. Moreover, Anritsu Corporation will deem this warranty void when:

•The fault is outside the scope of the warranty conditions separately described in the

operation manual.

•The fault is due to mishandling, misuse, or unauthorized modification or repair of the

equipment by the customer.

•The fault is due to severe usage clearly exceeding normal usage.

•The fault is due to improper or insufficient maintenance by the customer.

•The fault is due to natural disaster, including fire, wind, flooding, earthquake,

lightning strike, or volcanic ash, etc.

•The fault is due to damage caused by acts of destruction, including civil disturbance,

riot, or war, etc.

•The fault is due to explosion, accident, or breakdown of any other machinery, facility, or

plant, etc.

•The fault is due to use of non-specified peripheral or applied equipment or parts, or

consumables, etc.

•The fault is due to use of a non-specified power supply or in a non-specified installation

location.

•The fault is due to use in unusual environments(Note).

•The fault is due to activities or ingress of living organisms, such as insects, spiders,

fungus, pollen, or seeds.

In addition, this warranty is valid only for the original equipment purchaser. It is not

transferable if the equipment is resold. Anritsu Corporation shall assume no liability for

injury or financial loss of the customer due to the use of or a failure to be able to use this

equipment.

Note: For the purpose of this Warranty, "unusual environments" means use:

•In places of direct sunlight

•In dusty places

•Outdoors

•In liquids, such as water, oil, or organic solvents, and medical fluids, or places where

these liquids may adhere

•In salty air or in places where chemically active gases (sulfur dioxide, hydrogen sulfide,

chlorine, ammonia, nitrogen dioxide, or hydrogen chloride, etc.) are present

•In places where high-intensity static electric charges or electromagnetic fields are

present

•In places where abnormal power voltages (high or low) or instantaneous power failures

occur

•In places where condensation occurs

•In the presence of lubricating oil mists

•In places at an altitude of more than 2,000 m

•In the presence of frequent vibration or mechanical shock, such as in cars, ships, or

airplanes

Safety-6

Software End-User License Agreement (EULA)

Please read this Software End-User License Agreement (hereafter this EULA) carefully

before using (includes executing, copying, registering, etc.) this software (includes

programs, databases, scenarios, etc., used to operate, set, etc., Anritsu electronic

equipment). By reading this EULA and using this software, you are agreeing to be bound

by the terms of its contents and Anritsu Corporation (hereafter Anritsu) hereby grants

you the right to use this Software with the Anritsu-specified equipment (hereafter

Equipment) for the purposes set out in this EULA.

1. Grant of License and Limitations

a. Regardless of whether this Software was purchased from or provided free-of-charge by

Anritsu, you agree not to rent, lease, lend, or otherwise distribute this Software to third

parties and further agree not to disassemble, recompile, reverse engineer, modify, or

create derivative works of this Software.

b. You may make one copy of this Software for backup purposes only.

c. You are not permitted to reverse engineer this software.

d. This EULA allows you to install one copy of this Software on one piece of Equipment.

2. Disclaimers

To the extent not prohibited by law, in no event shall Anritsu be liable for personal

injury, or any incidental, special, indirect or consequential damages whatsoever,

including, without limitation, damages for loss of profits, loss of data, business

interruption or any other commercial damages or losses, arising out of or related to your

use or inability to use this Software.

3. Limitation of Liability

a. If a fault (bug) is discovered in this Software, preventing operation as described in the

operation manual or specifications whether or not the customer uses this software as

described in the manual, Anritsu shall at its own discretion, fix the bug, or exchange

the software, or suggest a workaround, free-of-charge. However, notwithstanding the

above, the following items shall be excluded from repair and warranty.

i. If this Software is deemed to be used for purposes not described in the operation

manual or specifications.

ii. If this Software is used in conjunction with other non-Anritsu-approved software.

iii. Recovery of lost or damaged data.

iv. If this Software or the Equipment has been modified, repaired, or otherwise

altered without Anritsu's prior approval.

v. For any other reasons out of Anritsu's direct control and responsibility, such as

but not limited to, natural disasters, software virus infections, etc.

b. Expenses incurred for transport, hotel, daily allowance, etc., for on-site repairs by

Anritsu engineers necessitated by the above faults shall be borne by you.

c. The warranty period for faults listed in article 3a above covered by this EULA shall be

either 6 months from the date of purchase of this Software or 30 days after the date of

repair, whichever is longer.

Safety-7

4. Export Restrictions

You may not use or otherwise export or re-export directly or indirectly this Software

except as authorized by Japanese and United States law. In particular, this software

may not be exported or re-exported (a) into any Japanese or US embargoed countries or

(b) to anyone on the Japanese or US Treasury Department's list of Specially Designated

Nationals or the US Department of Commerce Denied Persons List or Entity List. By

using this Software, you warrant that you are not located in any such country or on any

such list. You also agree that you will not use this Software for any purposes prohibited

by Japanese and US law, including, without limitation, the development, design and

manufacture or production of missiles or nuclear, chemical or biological weapons of mass

destruction.

5. Termination

Anritsu shall deem this EULA terminated if you violate any conditions described herein.

This EULA shall also be terminated if the conditions herein cannot be continued for any

good reason, such as violation of copyrights, patents, or other laws and ordinances.

6. Reparations

If Anritsu suffers any loss, financial or otherwise, due to your violation of the terms of

this EULA, Anritsu shall have the right to seek proportional damages from you.

7. Responsibility after Termination

Upon termination of this EULA in accordance with item 5, you shall cease all use of this

Software immediately and shall as directed by Anritsu either destroy or return this

Software and any backup copies, full or partial, to Anritsu.

8. Dispute Resolution

If matters of dispute or items not covered by this EULA arise, they shall be resolved by

negotiations in good faith between you and Anritsu.

9. Court of Jurisdiction

This EULA shall be interpreted in accordance with Japanese law and any disputes that

cannot be resolved by negotiation described in Article 8 shall be settled by the Japanese

courts.

Safety-8

CE Conformity Marking

Anritsu affixes the CE conformity marking on the following product(s) in accordance with the

Decision 768/2008/EC to indicate that they conform to the EMC, LVD, and RoHS directive of

the European Union (EU).

1. Product Model

Model:MT8852B Bluetooth Test Set

2. Applied Directive

EMC: Directive 2014/30/EU

LVD: Directive 2014/35/EU

RoHS:Directive 2011/65/EU

3. Applied Standards

• EMC:Emission:EN 61326-1: 2013 (Class A)

Immunity:EN 61326-1: 2013 (Table 2)

*: Performance Criteria

A: The equipment shall continue to operate as intended during and after the test.

No degradation of performance or loss of function is allowed below a performance

level specified by the manufacturer, when the equipment is used as intended.

The performance level may be replaced by a permissible loss of performance. If

the minimum performance level or the permissible performance loss is not

specified by the manufacturer, either of these may be derived from the product

description and documentation and what the user may reasonably expect from

the equipment if used as intended.

Performance Criteria*

IEC 61000-4-2 (ESD) B

IEC 61000-4-3 (EMF) A

IEC 61000-4-4 (Burst) B

IEC 61000-4-5 (Surge) B

IEC 61000-4-6 (CRF) A

EC 61000-4-8 (RPFMF) A

IEC 61000-4-11 (V dip/short) B,C

Safety-9

B. The equipment shall continue to operate as intended after the test. No

degradation of performance or loss of function is allowed below a performance

level specified by the manufacturer, when the equipment is used as intended.

The performance level may be replaced by a permissible loss of performance.

During the test, degradation of performance is however allowed. No change of

actual operating state or stored data is allowed. If the minimum performance

level or the permissible performance loss is not specified by the manufacturer,

either of these may be derived from the product description and documentation

and what the user may reasonably expect from the equipment if used as

intended.

C. Temporary loss of function is allowed, provided the function is self-recoverable or

can be restored by the operation of the controls.

Harmonic current emissions:

EN 61000-3-2: 2006 +A1:2009 A2:2009

(Class A equipment)

No limits apply to this equipment with an active input power under 75 W.

• LVD:EN 61010-1: 2010 (Pollution Degree 2)

• RoHS:EN 50581: 2012 (Category 9)

4. Authorized representative

Name: Murray Coleman

Head of Customer Service EMEA

ANRITSU EMEA Ltd.

Address, city: 200 Capability Green, Luton

Bedfordshire, LU1 3LU

Country: United Kingdom

Autres manuels pour MT8852B

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Anritsu Instrument de mesure

Anritsu

Anritsu S331E Manuel utilisateur

Anritsu

Anritsu Site Master Manuel utilisateur

Anritsu

Anritsu 37 D Series Manuel utilisateur

Anritsu

Anritsu MS2690A Manuel utilisateur

Anritsu

Anritsu MD1230B Manuel utilisateur

Anritsu

Anritsu MP1590B Manuel utilisateur

Anritsu

Anritsu VNA Master MS203 A Series Manuel utilisateur

Anritsu

Anritsu VNA Master MS2026C Manuel du propriétaire

Anritsu

Anritsu BTS Master MT8220T Manuel du propriétaire

Anritsu

Anritsu MP1632C Manuel utilisateur

Anritsu

Anritsu MS2722C Manuel utilisateur

Anritsu

Anritsu SM/PL Series Manuel d'utilisation et d'entretien

Anritsu

Anritsu Sire Master S331D Manuel utilisateur

Anritsu

Anritsu ShockLine MS46131A-020 Manuel utilisateur

Anritsu

Anritsu PIM Master MW8208A Manuel utilisateur

Anritsu

Anritsu K250 Manuel utilisateur

Anritsu

Anritsu IQ Fiber Master MT2780A Manuel utilisateur

Anritsu

Anritsu MP1800A Manuel utilisateur

Anritsu

Anritsu MP1800A Manuel utilisateur

Anritsu

Anritsu BTS Master MT8221B Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2721A Manuel utilisateur

Anritsu

Anritsu VectorStar ME7848E Series Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2720T Manuel utilisateur

Anritsu

Anritsu ML248 A Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur