Anritsu MT8801C Manuel utilisateur

The test & measurement

equipment you need at

the price you want.

Alltest carries the world’s largest selection of

used/refurbished benchtop test & measurement

equipment at 50% the price of new.

Our equipment is guaranteed working, warrantied, and

available with certified calibration from our in-house staff

of technicians and engineers.

• 10+ full time technicians with over 150 years of

specialization

• 90 day warranty & 5 day right of return on all

equipment

•

• 1-3 year warranties for new and

premium-refurbished equipment

• Every unit tested to OEM specifications

• Satisfaction guaranteed

You have plans, we will help you achieve them.

Any project. Any budget.

Get a quote today!

CCall (732) 919-3339 or email sales@alltest.net.

Alltest Instruments, Inc.

500 Central Ave.

Farmingdale, NJ 07727

P: (732) 919-3339

F: (732) 919-3332

alltest.net

sales@alltest.net

Fourth Edition

Read this manual before using the equipment.

Keep this manual with the equipment.

MT8801C

Option 12: CDMA Measurement

Operation Manual

Document No.: M-W1673AE-4.0

ANRITSU CORPORATION

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following

safety symbols to indicate safety-related information. Insure that you clearly understand the meanings of the symbols

BEFORE using the equipment. Some or all of the following five symbols may not be used on all Anritsu equipment.

In addition, there may be other labels attached to products which are not shown in the diagrams in this manual.

Symbols used in manual

DANGER

WARNING

CAUTION

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Insure that you clearly understand the meanings of the symbols

and take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is indi-

cated symbolically in or near the circle.

This indicates warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MT8801C

Option 12: CDMA Measurement

Operation Manual

15 December 1999 (First Edition)

10 December 2003 (Fourth Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols

iii

For Safety

WARNING

1. ALWAYS refer to the operation manual when working near locations at

which the alert mark shown on the left is attached. If the operation, etc.,

is performed without heeding the advice in the operation manual, there

is a risk of personal injury. In addition, the equipment performance may

be reduced.

Moreover, this alert mark is sometimes used with other marks and de-

scriptions indicating other dangers.

2. Measurement Categories

This instrument is designed for Measurement category I (CAT I). Don't

use this instrument at the locations of measurement categories from

CAT II to CAT IV.

In order to secure the safety of the user making measurements, IEC

61010 clarifies the range of use of instruments by classifying the loca-

tion of measurement into measurement categories from I to IV.

The category outline is as follows:

Measurement category I (CAT I):

Secondary circuits of a device connected to an outlet via a power trans-

former etc.

Measurement category II (CAT II):

Primary circuits of a device with a power cord (portable tools, home

appliance etc.) connected to an outlet.

Measurement category III (CAT III):

Primary circuits of a device (fixed equipment) to which power is directly

supplied from the power distribution panel, and circuits from the distri-

bution panel to outlets.

Measurement category IV (CAT IV):

All building service-line entrance circuits through the integrating watt-

meter and primary circuit breaker (power distribution panel).

3. When supplying power to this equipment, connect the accessory 3-pin

power cord to a grounded outlet. If a grounded outlet is not available,

before supplying power to the equipment, use a conversion adapter and

ground the green wire, or connect the frame ground on the rear panel of

the equipment to ground. If power is supplied without grounding the

equipment, there is a risk of receiving a severe or fatal electric shock.

For Safety

WARNING

4. This equipment cannot be repaired by the user. DO NOT attempt to

open the cabinet or to disassemble internal parts. Only Anritsu-trained

service personnel or staff from your sales representative with a knowl-

edge of electrical fire and shock hazards should service this equipment.

There are high-voltage parts in this equipment presenting a risk of se-

vere injury or fatal electric shock to untrained personnel. In addition,

there is a risk of damage to precision parts.

5. This equipment should be used in the correct position. If the cabinet is

turned on its side, etc., it will be unstable and may be damaged if it falls

over as a result of receiving a slight mechanical shock.

And also DO NOT use this equipment in the position where the power

switch operation is difficult.

6. DO NOT short the battery terminals and never attempt to disassemble it

or dispose of it in a fire. If the battery is damaged by any of these

actions, the battery fluid may leak.

This fluid is poisonous.

DO NOT touch it, ingest it, or get in your eyes. If it is accidentally in-

gested, spit it out immediately, rinse your mouth with water and seek

medical help. If it enters your eyes accidentally, do not rub your eyes,

irrigate them with clean running water and seek medical help. If the

liquid gets on your skin or clothes, wash it off carefully and thoroughly.

7. This instrument uses a Liquid Crystal Display (LCD); DO NOT subject

the instrument to excessive force or drop it. If the LCD is subjected to

strong mechanical shock, it may break and liquid may leak.

This liquid is very caustic and poisonous.

DO NOT touch it, ingest it, or get in your eyes. If it is ingested acciden-

tally, spit it out immediately, rinse your mouth with water and seek medi-

cal help. If it enters your eyes accidentally, do not rub your eyes, irrigate

them with clean running water and seek medical help. If the liquid gets

on your skin or clothes, wash it off carefully and thoroughly.

Repair

WARNING

Falling Over

Battery Fluid

LCD

For Safety

CAUTION

1. Before Replacing the fuses, ALWAYS remove the power cord from the

poweroutlet and replace the blown fuses. ALWAYS use new fuses of

the type and rating specified on the fuse marking on the rear panel of

the cabinet.

T6.3A indicates a time-lag fuse.

T6.3A or F6.3A indicate a normal fusing type fuse.

There is risk of receiving a fatal electric shock if the fuses are replaced

with the power cord connected.

2. Keep the power supply and cooling fan free of dust.

• Clean the power inlet regularly. If dust accumulates around the

power pins, there is a risk of fire.

• Keep the cooling fan clean so that the ventilation holes are not ob-

structed. If the ventilation is obstructed, the cabinet may overheat

and catch fire.

3. Use two or more people to lift and move this equipment, or use a trolley.

There is a risk of back injury, if this equipment is lifted by one person.

4. Never input a signal of more than the specified voltage between the

measured terminal and ground. Input of an excessive signal may dam-

age the equipment.

5. Do not take out the floppy disk if the lamp of the floppy disk drive is on.

If it is taken out, the contents of the storage medium will be damaged,

resulting in floppy disk drive failure.

Replacing Fuse

CAUTION

Cleaning

Check Terminal

For Safety

CAUTION

The power for memory back-up of the MT8801C is supplied by a poly-

carbomonofluoride lithium battery. this battery should only be replaced by

a battery of the same type; since replacement can only be made by Anritsu,

contact the nearest Anritsu representative when replacement is required.

At the end of it's life, the battery should be recycled or disposed properly.

Note: The Battery life is about 7 years. Early battery replacement is rec-

ommended.

The MT8801C stores data and programs using a floppy disk (FD), memory

card (MC), and backed-up memories.

Data and programs may be lost due to improper use or failure.

Anritsu therefore recommends that you back up the memory.

ANRITSU CANNOT COMPENSATE FOR ANY MEMORY LOSS.

Please pay careful attention to the following points. Do not remove the

floppy disk from the equipment being accessed.

(FD)

•Do not touch the FD directly or by using any object.

•Do not place the equipment where dirty and dusty.

•Isolate the FD and memory card from static electricity.

•Avoid to placing the FD in direct sunlight or near heating sources.

•Store under temperature of 40˚to 54˚C, humidity of 8 to 90%

(No condensation).

(Memory card)

•Isolate the memory card from static electricity.

(Backed-up memory)

•Isolate the memory from static electricity.

The MT8801C uses chemical compound semiconductor including arsenic.

At the end of its life, the MT8801C should be recycled or disposed properly

according to the local disposal regulations.

Replacing Memory

Back-up Battery

External

Storage Media

Disposing of Product

vii

Equipment Certificate

Anritsu Corporation certifies that this equipment was tested before shipment using

calibrated measuring instruments with direct traceability to public testing organiza-

tions recognized by national research laboratories including the National Institute of

Advanced Industrial Science and Technology, and the Communications Research

Laboratory, and was found to meet the published specifications.

Anritsu Warranty

Anritsu Corporation will repair this equipment free-of-charge if a malfunction occurs

within 1 year after shipment due to a manufacturing fault, provided that this warranty is

rendered void under any or all of the following conditions.

• The fault is outside the scope of the warranty conditions described in the operation

manual.

• The fault is due to mishandling, misuse, or unauthorized modification or repair of

the equipment by the customer.

• The fault is due to severe usage clearly exceeding normal usage.

• The fault is due to improper or insufficient maintenance by the customer.

• The fault is due to natural disaster including fire, flooding, earthquake, etc.

• The fault is due to use of non-specified peripheral equipment, peripheral parts,

consumables, etc.

• The fault is due to use of a non-specified power supply or in a non-specified instal-

lation location.

In addition, this warranty is valid only for the original equipment purchaser. It is not

transferable if the equipment is resold.

Anritsu Corporation will not accept liability for equipment faults due to unforeseen and

unusual circumstances, nor for faults due to mishandling by the customer.

Anritsu Corporation Contact

If this equipment develops a fault, contact Anritsu Service and Sales offices at the

address at the end of paper-edition manual or the separate file of CD-edition manual.

viii

Software License Agreement

Please read this Software License Agreement before using the accompanying software

program (hereafter this software).

You are authorized to use this software only if you agree to all the terms of this License.

By opening the sealed package containing this software, you are agreeing to be bound

by the terms of this License.

If you do not agree to these terms, return the unopened software package to Anritsu

Corporation (hereafter Anritsu).

1. License

(1) This License gives you the right to use this software on one MT8801C Radio

Communication Analyzer, MX880201A CDMA Measurement Software

(hereafter computer system).

(2) To use this software on one computer system, this License allows you to make

one copy of this software on the storage device of your computer system.

(3) You must obtain a site license to use this software on more than one computer

system even if such computer systems are not operating simultaneously.

2. Copyright

(1) Although you are licensed to use this software, Anritsu retains the copyright.

(2) Although you have purchased this software, rights other than those specified in

this License are not transferred to you.

(3) You may not print, copy, modify, create derivative works, incorporate in other

software programs, decompile or disassemble this software in whole or in part,

without obtaining prior written permission from Anritsu.

3. Copying

Notwithstanding item (3) of section 2 above, you may make one copy of this soft-

ware for backup purposes only. In this case, you may only use either the backup

copy or the original copy of this software.

4. Termination

(1) Anritsu will deem this License to be automatically terminated if you fail to com-

ply with any provision of this License. Upon termination, you will lose all rights

to this software.

(2) Either party (Anritsu or yourself) to this Software License Agreement may ter-

minate this Agreement by giving 1 months notice in writing to the other party.

(3) Upon termination of this License for any reason, you must either immediately

destroy this software and related documentation, or return it to Anritsu.

Front Panel Power Switch

To prevent malfunction caused by accidental touching, the front power switch of this equipment turns on the

power if it is pressed continuously for about one second in the standby state. If the switch is pressed continu-

ously for one second in the power-on state, the equipment enters the standby state.

In the power-on state, if the power plug is removed from the outlet, then reinserted into it, the power will not

be turned on. Also, if the lines is disconnected due to momentary power supply interruption or power failure,

the power will not be turned on (enters the standby state) even if the line is recovered.

This is because this equipment enters the standby state and prevents incorrect data from being acquired when

the line has to be disconnected and reconnected.

For example, if the data acquisition requires a long time at the BER measurement, momentary power supply

interruption (power failure) might occur during measurement and the line could be recovered automatically

to power-on. In such a case, the equipment may mistake incorrect data for correct data without recognizing

the momentary power supply interruption.

If this equipment enters the standby state due to momentary power supply interruption or power failure,

check the state of the measuring system and press the front power switch to restore power to this equipment.

Further, if this equipment is built into a system and the system power has to be disconnected then recon-

nected, the power for this equipment must also be restored by pressing the front power switch.

Consequently, if this equipment is built into remote monitoring systems that use MODEMs, the standby

function of this equipment must be modified.

Autres manuels pour MT8801C

Table des matières

Autres manuels Anritsu Instrument de mesure

Anritsu

Anritsu Site Master S251C Manuel utilisateur

Anritsu

Anritsu Network Master MU909020A Manuel utilisateur

Anritsu

Anritsu Field Master Pro MS2090A Manuel du propriétaire

Anritsu

Anritsu VectorStar ME7838 Series Manuel utilisateur

Anritsu

Anritsu VectorStar ME7838 4 Series Manuel utilisateur

Anritsu

Anritsu ML2437A Manuel du propriétaire

Anritsu

Anritsu VectorStar ME7838AX Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2712E Manuel utilisateur

Anritsu

Anritsu BTS Master MT8222A Manuel utilisateur

Anritsu

Anritsu VNA Master MS2026C Manuel utilisateur

Anritsu

Anritsu MS2690A Manuel utilisateur

Anritsu

Anritsu 37 C Series Manuel utilisateur

Anritsu

Anritsu Network Master Series Manuel utilisateur

Anritsu

Anritsu VNA Master MS203 A Series Manuel utilisateur

Anritsu

Anritsu MS2840A-040 Manuel utilisateur

Anritsu

Anritsu MS2711A Manuel utilisateur

Anritsu

Anritsu BTS Master Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2720T Manuel utilisateur

Anritsu

Anritsu VectorStar ME7838E4X Manuel utilisateur

Anritsu

Anritsu MS2681A Manuel utilisateur

Anritsu

Anritsu MS2690A Manuel utilisateur

Anritsu

Anritsu MT8212E Manuel utilisateur

Anritsu

Anritsu Microwave Site Master S820E Manuel utilisateur

Anritsu

Anritsu MS9710C Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur