Anritsu Site Master S331L Manuel utilisateur

Maintenance Manual

Site Master™

S331L

Handheld Cable and Antenna Analyzer

Featuring Classic and Advanced Modes

2 MHz to 4 GHz Cable & Antenna Analyzer

50 MHz to 4 GHz Power Meter

Anritsu Company

490 Jarvis Drive

Morgan Hill, CA 95037-2809

USA

Part Number: 10580-00323

Revision: B

Published: August 2012

TRADEMARK ACKNOWLEDGMENTS

Windows, Windows XP, and Windows CE are all registered trademarks of Microsoft Corporation.

Acrobat Reader is a registered trademark of Adobe Corporation.

Site Master is a trademark of Anritsu Company.

NOTICE

Anritsu Company has prepared this manual for use by Anritsu Company personnel and customers as a guide for the

proper installation, operation and maintenance of Anritsu Company equipment and computer programs. The

drawings, specifications, and information contained herein are the property of Anritsu Company, and any

unauthorized use or disclosure of these drawings, specifications, and information is prohibited; they shall not be

reproduced, copied, or used in whole or in part as the basis for manufacture or sale of the equipment or software

programs without the prior written consent of Anritsu Company.

UPDATES

Updates, if any, can be downloaded from the Documents area of the Anritsu Website at:

http://www.anritsu.com

For the latest service and sales contact information in your area, please visit:

http://www.anritsu.com/contact.asp

S331L MM PN: 10580-00323 Rev. B Safety-1

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Company uses the

following symbols to indicate safety-related information. For your own safety, please read the information

carefully before operating the equipment.

Symbols Used in Manuals

Safety Symbols Used on Equipment and in Manuals

The following safety symbols are used inside or on the equipment near operation locations to provide

information about safety items and operation precautions. Ensure that you clearly understand the meanings of

the symbols and take the necessary precautions before operating the equipment. Some or all of the following

five symbols may or may not be used on all Anritsu equipment. In addition, there may be other labels attached

to products that are not shown in the diagrams in this manual.

Danger

This indicates a risk from a very dangerous condition or procedure that could result in

serious injury or death and possible loss related to equipment malfunction. Follow all

precautions and procedures to minimize this risk.

Warning This indicates a risk from a hazardous condition or procedure that could result in

light-to-severe injury or loss related to equipment malfunction. Follow all precautions

and procedures to minimize this risk.

Caution

This indicates a risk from a hazardous procedure that could result in loss related to

equipment malfunction. Follow all precautions and procedures to minimize this risk.

This indicates a prohibited operation. The prohibited operation is indicated symbolically

in or near the barred circle.

This indicates a compulsory safety precaution. The required operation is indicated

symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or near

the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

Safety-2 PN: 10580-00323 Rev. B S331L MM

For Safety

Warning Always refer to the operation manual when working near locations at which

the alert mark, shown on the left, is attached. If the operation, etc., is

performed without heeding the advice in the operation manual, there is a

risk of personal injury. In addition, the equipment performance may be

reduced.

Moreover, this alert mark is sometimes used with other marks and

descriptions indicating other dangers.

Warning

When supplying power to this equipment, connect the accessory 3-pin

power cord to a 3-pin grounded power outlet. If a grounded 3-pin outlet is

not available, use a conversion adapter and ground the green wire, or

connect the frame ground on the rear panel of the equipment to ground. If

power is supplied without grounding the equipment, there is a risk of

receiving a severe or fatal electric shock.

Warning

This equipment can not be repaired by the operator. Do not attempt to

remove the equipment covers or to disassemble internal components.

Only qualified service technicians with a knowledge of electrical fire and

shock hazards should service this equipment. There are high-voltage parts

in this equipment presenting a risk of severe injury or fatal electric shock to

untrained personnel. In addition, there is a risk of damage to precision

components.

Warning

Use two or more people to lift and move this equipment, or use an

equipment cart. There is a risk of back injury if this equipment is lifted by

one person.

Caution

Electrostatic Discharge (ESD) can damage the highly sensitive circuits in

the instrument. ESD is most likely to occur as test devices are being

connected to, or disconnected from, the instrument’s front and rear panel

ports and connectors. You can protect the instrument and test devices by

wearing a static-discharge wristband. Alternatively, you can ground

yourself to discharge any static charge by touching the outer chassis of the

grounded instrument before touching the instrument’s front and rear panel

ports and connectors. Avoid touching the test port center conductors

unless you are properly grounded and have eliminated the possibility of

static discharge.

Repair of damage that is found to be caused by electrostatic discharge is

not covered under warranty.

S331L MM PN: 10580-00323 Rev. B Contents-1

Table of Contents

Chapter 1—General Information

1-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1-2 Anritsu Customer Service Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1-3 Recommended Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1-4 Replaceable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1-5 Firmware Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Chapter 2—S331L Performance Verification

2-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2-2 Frequency Accuracy Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2-3 Return Loss Accuracy Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

2-4 Power Meter Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

2-5 InstaCal Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Chapter 3—Battery Information

3-1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Chapter 4—Assembly Replacement

4-1 Replacing the S331L Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4-2 Removing the Rear Case to Gain Access to Internal Assemblies . . . . . . . . . . . . . . . . . . . . . . 4-3

4-3 Main/VNA PCB Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

4-4 InstaCal / Power Meter Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

4-5 LCD and Touch Screen Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

4-6 Keypad PCB and Rubber Keypad Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

4-7 SOM Module Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Chapter 5—Troubleshooting

5-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Appendix A—Test Records

A-1 Test Records for Cable and Antenna Analyzer Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

A-2 Test Records for Power Meter Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

A-3 Test Records for InstaCal Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4

Contents-2 PN: 10580-00323 Rev. B S331L MM

S331L MM PN: 10580-00323 Rev. B 1-1

Chapter 1 — General Information

1-1 Introduction

This manual provides maintenance instructions for Anritsu Site Master Model S331L. The manual includes:

•General information in this chapter, including:

•Verification Equipment List (Table 1-1)

•Replaceable parts list (Table 1-2)

•Performance verification procedures (Chapter 2, “S331L Performance Verification”)

•Battery pack information (Chapter 3, “Battery Information”)

•Parts replacement procedures (Chapter 4, “Assembly Replacement”)

•Troubleshooting procedures (Chapter 5, “Troubleshooting”)

•Blank test records are included in Appendix A.

•Copy the blank test records from Appendix A and use them to record measured values. These test

records form a record of the performance of your instrument. Anritsu recommends that you make a

copy of the blank test records to document the measurements each time a Performance

Verification is performed. Continuing to document this process each time it is performed provides

a detailed history of instrument performance, which can allow you to observe trends.

Familiarity with the basic operation of the front panel keys (for example, how to change measurement mode,

preset the unit, or the meaning of soft key or submenu) is assumed. Refer to the instrument’s User Guide for

additional information.

1-2 Anritsu Customer Service Centers

For the latest service and sales information in your area, please visit the following URL:

http://www.anritsu.com/contact.asp

From here, you can select the latest sales, select service and support contact information in your country or

region, provide online feedback, complete a “Talk to Anritsu” form to have your questions answered, or obtain

other services offered by Anritsu.

Updated product information can be found on the Anritsu web site:

http://www.anritsu.com/

Search for the product model number. The latest documentation is on the product page under the Library tab.

Example URL for Site Master S331L:

http://www.anritsu.com/en-us/products-solutions/products/s331l.aspx

Caution Before making any measurement, verify that all equipment has warmed up for at least 30 minutes.

1-3 Recommended Test Equipment General Information

1-2 PN: 10580-00323 Rev. B S331L MM

1-3 Recommended Test Equipment

The following test equipment is recommended for use in testing and maintaining the S331L. Table 1-1 is a list

of test equipment that is required for verifying the S331L Cable and Antenna Analyzer.

Table 1-1. Test Equipment Required for Cable and Antenna Analyzer Verification and Calibration

Instrument Critical Specification Recommended Manufacturer/Model

Frequency Counter Frequency: 2 GHz Anritsu Model MF2412B

Open/Short Frequency: DC to 18 GHz Anritsu Model 22N50

Precision Load Frequency: DC to 18 GHz

Return Loss: 40 dB min.

Anritsu Model SM/PL-1

6 dB Offset Termination Frequency: DC to 4.0 GHz Anritsu Model SC5905

20 dB Offset Termination Frequency: DC to 4.0 GHz Anritsu Model SC5906

Synthesized Signal Source Frequency: 0.1 Hz to 6 GHz

Power Output to +13 dBm

Anritsu Model MG3692B with

options 2, 3, 4, 22, 15

Power Meter Power Range: −70 dBm to +20 dBm Anritsu Single Channel Model ML2437A

Power Sensor Frequency: 100 kHz to 18 GHz

Power Range: –55 dBm to +20 dB

Anritsu Model SC7400

Power Splitter Frequency: DC to 18 GHz Aeroflex/Weinschel Model 1870A

RF Coaxial Cable Frequency: DC to 18 GHz

N(m) to N(m), 50 ohm

Anritsu Model 15NN50-0.6B

RF Coaxial Cable Frequency: DC to 18 GHz N(m) to N(f),

50 ohm

Anritsu Model 15NNF50-0.6B

General Information 1-4 Replaceable Parts

S331L MM PN: 10580-00323 Rev. B 1-3

1-4 Replaceable Parts

1-5 Firmware Updates

Refer to the S331L User Guide (Anritsu Part Number 10580-00321) for the procedure on updating the

firmware.

Table 1-2. List of Replaceable Parts

Part Number Description

ND72098 S331L MB/VNA PCB Assembly Including SOM Module and Shields

3-2000-1674 SOM Module

ND72099 Power Meter / InstaCal Module with 4 screws

3-15-160 LCD Display including Touch Screen

2000-1676-R Soft Carrying Case

3-72223 Stylus Pen and Leash (attaches to the Soft Carrying Case)

ND74880 Front Case with model ID label, Encoder and Knob

ND74881 Rear Case with 4 screws, Anritsu Label, SN Label and Windows License

3-72332-1 Model S311L ID Label

ND74882 Battery Cover with 6 screws

ND74886 Li-ion Batteries (Qty 2)

ND74895 USB Cover

ND74883 Top Plate with 6 screws

3-72321 Top Bumper

3-72307-2 Bottom Bumper

ND74884 N Connector Plate with cover, nut and washer

3-72317-1 Keypad to Main board cable

3-70674-3 LCD to Main board cable

40-187-R AC to DC Power Converter

ND72100 Keypad PCB, includes speaker and 8 screws

3-71015 Rubber Keypad

3-61360-2 Knob (excluding encoder)

3-72305 Front LCD Gasket

3-72315 Rear LCD Gasket

ND74885 Bracket for the Main Board, includes battery foam and 8 screws

2000-1687-R N-connector Thumb Wheel

1-5 Firmware Updates General Information

1-4 PN: 10580-00323 Rev. B S331L MM

Autres manuels pour Site Master S331L

Table des matières

Autres manuels Anritsu Instrument de mesure

Anritsu

Anritsu ShockLine MS46131A-020 Manuel utilisateur

Anritsu

Anritsu VectorStar ME7848E Series Manuel utilisateur

Anritsu

Anritsu MS2070A Manuel utilisateur

Anritsu

Anritsu VectorStar ME7838D4 Manuel utilisateur

Anritsu

Anritsu VectorStar ME7848A Series Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2711D Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2720T Manuel utilisateur

Anritsu

Anritsu CMA50 Manuel utilisateur

Anritsu

Anritsu MT1100A Network Master Flex Manuel utilisateur

Anritsu

Anritsu Site Master S820D Manuel utilisateur

Anritsu

Anritsu Cell Master MT8212B Manuel utilisateur

Anritsu

Anritsu Site Master Manuel utilisateur

Anritsu

Anritsu Series MS278XB Manuel utilisateur

Anritsu

Anritsu SQA-R MP1900A Manuel utilisateur

Anritsu

Anritsu IQ Fiber Master Manuel utilisateur

Anritsu

Anritsu MX269017A Manuel utilisateur

Anritsu

Anritsu MT8801C Manuel utilisateur

Anritsu

Anritsu 3656C W1 Manuel utilisateur

Anritsu

Anritsu MP1590B Manuel utilisateur

Anritsu

Anritsu MP1220A Manuel utilisateur

Anritsu

Anritsu BTS Master MT8220T Manuel du propriétaire

Anritsu

Anritsu LMR Master S412E Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2721B Manuel utilisateur

Anritsu

Anritsu VNA Master MS2026C Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur