Anritsu Ms9710b Manuel utilisateur

Document No.: M-W1283AE-14.0

ANRITSU CORPORATION

MS9710B

Optical Spectrum Analyzer

Operation Manual

For safety and warning information, please read this

manual before attempting to use the equipment.

Keep this manual with the equipment.

14th Edition

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following

safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of the

symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols

and take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MS9710B

Optical Spectrum Analyzer

Operation Manual

8 May 1997 (First Edition)

17 July 2007 (14th Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

WARNING

1. ALWAYS refer to the operation manual when working near locations

at which the alert mark shown on the left is attached. If the advice in

the operation manual is not followed there is a risk of personal injury

or reduced equipment performance. The alert mark shown on the

left may also be used with other marks and descriptions to indicate

other dangers.

2. IEC 61010 Standard

The IEC 61010 standard specifies four categories to ensure that an

instrument is used only at locations where it is safe to make

measurements. This instrument is designed for measurement

category I (CAT I). DO NOT use this instrument at locations

specified as category II, III, or IV as defined below.

Measurement category I (CAT I):

Secondary circuits of a device that is not directly connected to a

power outlet.

Measurement category II (CAT II):

Primary circuits of a device that is directly connected to a power outlet,

e.g., portable tools or home appliance.

Measurement category III (CAT III):

Primary circuits of a device (fixed equipment) to which power is

supplied directly from the distribution panel, and circuits running from

the distribution panel to power outlet.

Measurement category IV (CAT IV):

Building service-line entrance circuits, and circuits running from the

service-line entrance to the meter or primary circuit breaker

(distribution panel).

For Safety

WARNING

3. Laser radiation warning

•NEVER look directly into the cable connector on the equipment

nor into the end of a cable connected to the equipment. There is

a risk of injury if laser radiation enters the eye.

•The Laser Safety label is attached to the equipment for safety use

as indicated in "Laser Safety" later in this section.

4. To ensure that the instrument is earthed, always use the supplied 3-

pin power cord, and insert the plug into an outlet with an earth

terminal. If power is supplied without earthing the equipment, there

is a risk of receiving a severe or fatal electric shock or causing

damage to the internal components.

5. This equipment cannot be repaired by the operator. DO NOT attempt

to remove the equipment covers or unit covers or to disassemble

internal components. Only qualified service personnel with a

knowledge of electrical fire and shock hazards should service this

equipment. There are high-voltage parts in this equipment presenting

a risk of severe injury or fatal electric shock to untrained personnel. In

addition, there is a risk of damage to precision components.

6. The performance-guarantee seal verifies the integrity of the equipment.

To ensure the continued integrity of the equipment, only Anritsu service

personnel, or service personnel of an Anritsu sales representative,

should break this seal to repair or calibrate the equipment. If the

performance-guarantee seal is broken by you or a third party, the

performance of the equipment cannot be guaranteed. Be careful not

to break the seal by opening the equipment or unit covers.

7. This equipment should always be positioned in the correct manner.

If the cabinet is turned on its side, etc., it will be unstable and may be

damaged if it falls over as a result of receiving a slight mechanical

shock.

Always set up the equipment in a position where the power switch

can be reached without difficulty.

Repair

Falling Over

Calibration

Electric Shock

For Safety

CAUTION

1. Always remove the mains power cable from the power outlet before

replacing blown fuses. There is a risk of electric shock if fuses are

replaced with the power cable connected. Always use new fuses of

the type and rating specified on the rear panel of the instrument.

There is a risk of fire if a fuse of a different rating is used.

T3.15A indicates a time-lag fuse.

2. Keep the power supply and cooling fan free of dust.

•Clean the power inlet regularly. If dust accumulates around the

power pins, there is a risk of fire.

•Keep the cooling fan clean so that the ventilation holes are not

obstructed. If the ventilation is obstructed, the cabinet may

overheat and catch fire.

Fuse Replacement

Cleaning

For Safety

The laser in this equipment is classified as Class 1 according to the IEC

60825-1:2001 specifications, or as Class I according to the 21 CFR

1040.10:1995 specifications. These classes of lasers are safe under

reasonably foreseeable operating conditions.

Table 1

Standard name

Model number IEC 60825-1 21 CFR 1040.10

MS9710B-03 Class 1 Class I

MS9710B-04 Class 1 Class I

MS9710B-05 Class 1 Class I

MS9710B-13 Class 1 Class I

MS9710B-14 Class 1 Class I

Class 1 indicate the danger degree of the laser radiation specified below

according to IEC 60825-1:2001.

Class 1: Lasers that are safe under reasonably foreseeable conditions

of operation, including the use of optical instruments for

intrabeam viewing.

Class I indicate the degree of danger of the laser radiation outlined below

as defined by 21 CFR 1040.10:1995.

Class I: Class I labels of laser radiation are not considered to be

hazardous.

CAUTION

Caution-Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous radiation

exposure.

The use of optical instruments with this product will increase eye hazard.

Laser Safety

For Safety

vii

Laser Radiation Markings

For Safety

viii

CAUTION

This equipment uses a Poly-carbomonofluoride lithium battery to backup

the memory. This battery must be replaced by service personnel when

it has reached the end of its useful life; contact the Anritsu sales section

or your nearest representative.

Note: The battery used in this equipment has a maximum useful life of

7 years. It should be replaced before this period has elapsed.

This equipment uses floppy disks as external storage media for storing

data and programs.

If this media is mishandled or becomes faulty, important data may be lost.

To prevent this chance occurrence, all important data and programs

should be backed-up.

Anritsu will not be held responsible for lost data.

Pay careful attention to the following points.

•Never remove the memory card from the pulse tester while it is being

accessed.

•The memory card may be damaged by static electric charges.

•The external storage media shipped with the instrument has been

thoroughly tested. Users should note that since all other devices

have not been tested in this manner, Anritsu is unable to guarantee

their performance or suitability.

Do not place in a dusty area.

Clean the magnetic head periodically to ensure normal operation.

Refer to the section on cleaning the head later in this manual.

Replacing Memory

Back-up Battery

External

Storage Media

Floppy Disk

Equipment Certificate

Anritsu Corporation certifies that this equipment was tested before

shipment using calibrated measuring instruments with direct traceability

to public testing organizations recognized by national research

laboratories, including the National Institute of Advanced Industrial

Science and Technology, and the National Institute of Information and

Communications Technology, and was found to meet the published

specifications.

Anritsu Warranty

Anritsu Corporation will repair this equipment free-of-charge if a

malfunction occurs within one year after shipment due to a manufacturing

fault, under the condition that this warranty is void when:

•The fault is outside the scope of the warranty conditions described in

the operation manual.

•The fault is due to mishandling, misuse, or unauthorized modification

or repair of the equipment by the customer.

•The fault is due to severe usage clearly exceeding normal usage.

•The fault is due to improper or insufficient maintenance by the

customer.

•The fault is due to natural disaster including fire, flooding, earthquake,

etc.

•The fault is due to use of non-specified peripheral equipment,

peripheral parts, consumables, etc.

•The fault is due to use of a non-specified power supply or in a non-

specified installation location.

In addition, this warranty is valid only for the original equipment

purchaser. It is not transferable if the equipment is resold.

Anritsu Corporation will not accept liability for equipment faults due to

unforeseen and unusual circumstances, nor for faults due to mishandling

by the customer.

Anritsu Corporation Contact

In the event that this equipment malfunctions, contact an Anritsu Service

and Sales office. Contact information can be found on the last page of

the printed version of this manual, and is available in a separate file on

the CD version.

Notes On Export Management

This product and its manuals may require an Export License/Approval by

the Government of the product's country of origin for re-export from you

country.

Before re-exporting the product or manuals, please contact us to confirm

whether they are export-controlled items or not.

When you dispose of export-controlled items, the products/manuals need to

be broken/shredded so as not to be unlawfully used for military purpose.

Reuse parts

Anritsu group promotes recycling activities in order to reuse available

resources and save energy. This product may use recycled parts

(mechanical components) that conform to Anritsu’s quality standards.

Lifetime of Parts

The life span of certain parts used in this instrument is determined by the

operating time or the power-on time. Due consideration should be given to

the life spans of these parts when performing continuous operation over an

extended period. These parts must be replaced at the customer's expense

even if within the guaranteed period described in Warranty at the beginning

of this manual. For details on life span, refer to the corresponding section in

this manual.

Autres manuels pour ms9710b

Table des matières

Autres manuels Anritsu Instrument de mesure

Anritsu

Anritsu Field Master Pro MS2090A Manuel utilisateur

Anritsu

Anritsu MS2830A Manuel utilisateur

Anritsu

Anritsu 37 D Series Manuel utilisateur

Anritsu

Anritsu S331E Manuel utilisateur

Anritsu

Anritsu VectorStar ME7838E4 Manuel utilisateur

Anritsu

Anritsu VNA master Manuel utilisateur

Anritsu

Anritsu VectorStar ME7848A Series Manuel utilisateur

Anritsu

Anritsu Field Master Manuel utilisateur

Anritsu

Anritsu S331E Manuel utilisateur

Anritsu

Anritsu MT1100A Network Master Flex Manuel utilisateur

Anritsu

Anritsu VectorStar ME7838AX Manuel utilisateur

Anritsu

Anritsu MS2722C Manuel utilisateur

Anritsu

Anritsu MS2690A Manuel utilisateur

Anritsu

Anritsu MS2024A Manuel d'utilisation et d'entretien

Anritsu

Anritsu MS2690A Manuel utilisateur

Anritsu

Anritsu LMR Master Manuel utilisateur

Anritsu

Anritsu Field Master Pro MS2090A Manuel utilisateur

Anritsu

Anritsu ShockLine MS46131A-010 Manuel utilisateur

Anritsu

Anritsu MT8820A Manuel utilisateur

Anritsu

Anritsu MW9076 Series Manuel utilisateur

Anritsu

Anritsu MD1230B Manuel utilisateur

Anritsu

Anritsu Site Master S113B Manuel utilisateur

Anritsu

Anritsu ML2437A Manuel du propriétaire

Anritsu

Anritsu Field Master MS2070A-703 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur

Anritsu ms9710b Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques