Anritsu MS2830A Manuel utilisateur

Document No.: M-W3336AE-31.0

ANRITSU CORPORATION

●For safety and warning information, please read this

manual before attempting to use the equipment.

●

Additional safety and warning information is provided

within the MS2830A Signal Analyzer Operation Manual

(Mainframe Operation) or MS2840A Signal Analyzer

Operation Manual (Mainframe Operation). Please also

refer to this document before using the equipment.

●

Keep this manual with the equipment.

MS2830A/MS2840A

Signal Analyzer

Operation Manual

Spectrum Analyzer Function

Operation

31st Edition

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the

following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of

the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and

take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is indicated

symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MS2830A/MS2840A

Signal Analyzer

Operation Manual Spectrum Analyzer Function Operation

15 December 2009 (First Edition)

17 March 2017 (31st Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

iii

Notes On Export Management

This product and its manuals may require an Export License/Approval by

the Government of the product's country of origin for re

export from your

country.

Before

re-

exporting the product or manuals, please contact us to confirm

whether they are export

-controlled items or not.

When you dispose of export

controlled items, the products/manuals need to

be broken/shredded so as not to be unlawfully used for military purpose.

Cautions against computer virus infection

●

Copying files and data

Only files that have been provided directly from Anritsu or generated

using Anritsu equipment should be copied to the instrument.

All other required files should be transferred by means of USB or

CompactFlash media after undergoing a thorough virus check.

●

Adding software

Do not download or install software that has not been specifically

recommended or licensed by Anritsu.

●

Network connections

Ensure that the network has sufficient anti-

virus security protection in

place.

About This Manual

Operation manual configuration

The operation manual configuration of the MS2830A, MS2840A Signal

Analyzer is shown below.

MS2690A/MS2691A/MS2692A Signal Analyzer Operation Manual

(

Main Frame O

eration

)

MS2690A/MS2691A/MS2692A and MS2830A/MS2840A

Signal Analyzer Operation Manual (Phase Noise Measurement Function Operation)

MS2690A/MS2691A/MS2692A and MS2830A/MS2840A

Signal Analyzer Operation Manual (Phase Noise Measurement Function Remote Control)

MS2690A/MS2691A/MS2692A and MS2830A/MS2840A

Signal Analyzer Operation Manual (Main Frame Remote Control)

MS2840A Signal Analyzer Operation Manual

(Main Frame Operation)

Or MS2830A Signal Analyzer Operation Manual

(

Main Frame O

eration

)

MS2690A/MS2691A/MS2692A

Signal Analyzer Operation Manual

(Signal Analyzer Function

Operation)

MS2690A/MS2691A/MS2692A and MS2830A/MS2840A

Signal Analyzer Operation Manual (Signal Analyzer Function Remote Control)

MS2830A/MS2840A

Signal Analyzer Operation Manual

(Signal Analyzer Function

Operation)

MS2690A/MS2691A/MS2692A

Spectrum Analyzer Operation Manual

(Spectrum Analyzer Function

Operation)

MS2690A/MS2691A/MS2692A and MS2830A/MS2840A

Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote Control)

MS2830A/MS2840A

Spectrum Analyzer Operation Manual

(Spectrum Analyzer Function

Operation)

Signal Analyzer Operation Manual (Mainframe Operation)

Signal Analyzer Operation Manual (Mainframe Remote Control)

Description of basic operations, maintenance procedures, common

functions and common remote functions of the mainframe

Signal Analyzer Operation Manual (Signal Analyzer Function Operation)

Signal Analyzer Operation Manual (Signal Analyzer Function Remote

Control)

Description of basic operations, functions and remote functions of the

signal analyzer

Signal Analyzer Operation Manual (Spectrum Analyzer Function

Operation) <This document>

Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote

Control)

Description of basic operations, functions and remote functions of the

spectrum analyzer

Signal Analyzer Operation Manual (Phase Noise Measurement Function)

Signal Analyzer Operation Manual (Phase Noise Measurement Function

Remote Control)

Description of basic operations, common functions and common

remote functions of the Phase Noise Measurement function

Convention Used in This Manual

Throughout this document, the use of MS2830A is assumed unless

otherwise specified. If using MS2840A, change MS2830A to read

MS2840A.

In this document, indicates a panel key.

III

Appendix Index

Table of Contents

About This Manual........................................ I

Chapter 1 Overview.................................... 1-1

1.1 Overview of Spectrum Analyzer ................................ 1-2

1.2 Features of Spectrum Analyzer ................................. 1-3

Chapter 2 Basic Operation ........................ 2-1

2.1 Display Description .................................................... 2-2

2.2 Single/Continuous Sweep.......................................... 2-4

2.3 Setting Frequency...................................................... 2-5

2.4 Setting Level .............................................................. 2-21

2.5 Setting RBW/VBW ..................................................... 2-37

Chapter 3 Display Mode Selection............ 3-1

3.1 Setting Storage Mode ................................................ 3-2

3.2 Setting Limit Line ....................................................... 3-10

3.3 Setting Normalize Function........................................ 3-28

3.4 Setting Math Function................................................. 3-31

3.5 Setting Time/Sweep................................................... 3-32

3.6 Save on Event............................................................ 3-37

Chapter 4 Marker Function........................ 4-1

4.1 Setting Marker............................................................ 4-2

4.2 Setting Peak Search Function ................................... 4-13

4.3 Displaying Marker List ............................................... 4-23

Chapter 5 Trigger Function and

Gate Function............................ 5-1

5.1 Setting Trigger Function ............................................ 5-2

5.2 Setting Gate Function ................................................ 5-10

Chapter 6 Measure Function..................... 6-1

6.1 Selecting Measure Function ...................................... 6-2

6.2 Adjacent Channel Leakage Power Measurement

(ACP) ......................................................................... 6-4

6.3 Burst Average Power Measurement.......................... 6-12

6.4 Channel Power Measurement (Channel Power) ....... 6-14

6.5 Occupied Bandwidth Measurement

(Occupied Bandwidth) ............................................... 6-16

6.6 Spectrum Emission Mask Measurement

(Spectrum Emission Mask)........................................ 6-18

6.7 Spurious Emission Measurement .............................. 6-28

6.8 Two-tone Third Order Intermodulation Distortion .... 6-42

6.9 Internal Signal Generator Control Function ............. 6-46

Chapter 7 Other Functions........................ 7-1

7.1 Selecting Other Function ........................................... 7-2

7.2 Setting Title................................................................ 7-3

7.3 Erasing Warmup Message ........................................ 7-4

7.4 Setting Uncal Message.............................................. 7-5

7.5 Adjusting Internal Reference Frequency Signal ........ 7-6

7.6 Input Source for Reference Frequency Signal .......... 7-7

7.7 Pre-Amp On/Off Display ............................................ 7-8

7.8 Preselector Tuning..................................................... 7-9

Chapter 8 External Mixer ........................... 8-1

8.1 External Mixer Overview............................................ 8-2

8.2 External Mixer............................................................ 8-3

8.3 Connecting External Mixer......................................... 8-8

8.4 Setting Band of External Mixer .................................. 8-9

8.5 Setting External Mixer Bias........................................ 8-11

8.6 Setting Conversion Loss............................................ 8-12

8.7 Distinguishing measured signal - Signal ID ............... 8-15

8.8 Setting Signal ID Mode .............................................. 8-17

8.9 Setting PS Function ................................................... 8-18

8.10 Setting External Mixer Cable Loss............................. 8-19

8.11 External Mixer Calibration Function........................... 8-22

Chapter 9 Noise Floor Reduction

.................................................... 9-1

9.1 Overview of Noise Floor Reduction ........................... 9-2

9.2 Noise Floor Reduction ............................................... 9-3

9.3 Acquiring Noise Floor Calibration Values .................. 9-5

9.4 Using Noise Floor Reduction ..................................... 9-8

9.5 Displaying Information of Noise Floor Calibration ..... 9-9

Appendix A Error Messages....................... A-1

Appendix B MS2830A Default Value List .. B-1

Appendix C MS2840A Default Value List .. C-1

Appendix D Standard Parameter List ........ D-1

Index .......................................................... Index-1

VI.

Autres manuels pour MS2830A

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Anritsu Instrument de mesure

Anritsu

Anritsu MS2690A Manuel utilisateur

Anritsu

Anritsu MS462 Series Manuel utilisateur

Anritsu

Anritsu MS2690A Manuel utilisateur

Anritsu

Anritsu G0430A Manuel utilisateur

Anritsu

Anritsu Spectrum Master Manuel utilisateur

Anritsu

Anritsu Field Master Manuel utilisateur

Anritsu

Anritsu 3656C W1 Manuel utilisateur

Anritsu

Anritsu Site Master Manuel utilisateur

Anritsu

Anritsu MS2722C Manuel utilisateur

Anritsu

Anritsu Field Master Pro MS2090A Manuel utilisateur

Anritsu

Anritsu VectorStar ME7838E4X Manuel utilisateur

Anritsu

Anritsu MS2690A Manuel utilisateur

Anritsu

Anritsu Site Master S331L Manuel utilisateur

Anritsu

Anritsu MS2840A-040 Manuel utilisateur

Anritsu

Anritsu VNA Master MS2026C Manuel du propriétaire

Anritsu

Anritsu Spectrum Master MS2721B Manuel du propriétaire

Anritsu

Anritsu Site Master S332D Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2721A Manuel utilisateur

Anritsu

Anritsu BTS Master MT8222A Manuel utilisateur

Anritsu

Anritsu 3GPP Manuel utilisateur

Anritsu

Anritsu MX269017A Manuel utilisateur

Anritsu

Anritsu MT8820A Manuel utilisateur

Anritsu

Anritsu HA-100 Series Manuel utilisateur

Anritsu

Anritsu VectorStar MS4640A Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur