Anritsu MS2830A Manuel utilisateur

Document No.: M-W3555AE-16.0

ANRITSU CORPORATION

MX269018A

Analog Measurement Software/

MS2830A Signal Analyzer

Analog Signal Generator

Operation Manual

Operation

16th Edition

•For safety and warning information, please read this

manual before attempting to use the equipment.

•

Additional safety and warning information is provided

within the MS2830A Signal Analyzer Operation Manual

(Mainframe: Operation). Please also refer to this

document before using the equipment.

•

Keep this manual with the equipment.

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the

following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of

the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and

take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MX269018A Analog Measurement Software/

MS2830A Signal Analyzer Analog Signal Generator

Operation Manual Operation

24 June 2011 (First Edition)

20 November 2015 (16th Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

CAUTION

•Never input a signal of more than the indicated value between the

measured terminal and ground. Input of an excessive signal may

damage the equipment.

Check Terminal

Equipment Certificate

Anritsu Corporation guarantees that this equipment was inspected at

shipment and meets the published specifications.

Anritsu Warranty

•During the warranty period, Anritsu Corporation will repair or exchange this

software free-of-charge if it proves defective when used as described in the

operation manual.

•The warranty period is 6 months from the purchase date.

•The warranty period after repair or exchange will remain 6 months from

the original purchase date, or 30 days from the date of repair or

exchange, depending on whichever is longer.

•This warranty does not cover damage to this software caused by Acts of

God, natural disasters, and misuse or mishandling by the customer.

In addition, this warranty is valid only for the original equipment purchaser. It

is not transferable if the equipment is resold.

Anritsu Corporation shall assume no liability for injury or financial loss of the

customer due to the use of or a failure to be able to use this equipment.

Anritsu Corporation Contact

In the event that this equipment malfunctions, contact an Anritsu Service and

Sales office. Contact information can be found on the last page of the printed

version of this manual, and is available in a separate file on the CD version.

Notes On Export Management

This product and its manuals may require an Export License/Approval by

the Government of the product's country of origin for re

export from your

country.

Before re

-exporting

the product or manuals, please contact us to confirm

whet

her they are export-controlled items or not.

When you dispose of export

controlled items, the products/manuals need

to be broken/shredded so as not to be unlawfully used for military purpose.

Software End-User License Agreement (EULA)

Please read this Software End-User License Agreement (hereafter this EULA) carefully before using

(includes executing, copying, registering, etc.) this software (includes programs, databases, scenarios, etc.,

used to operate, set, etc., Anritsu electronic equipment). By reading this EULA and using this software, you

are agreeing to be bound by the terms of its contents and Anritsu Corporation (hereafter Anritsu) hereby

grants you the right to use this Software with the Anritsu-specified equipment (hereafter Equipment) for the

purposes set out in this EULA.

1. Grant of License and Limitations

1. Regardless of whether this Software was

purchased from or provided free-of-charge by

Anritsu, you agree not to rent, lease, lend, or

otherwise distribute this Software to third

parties and further agree not to disassemble,

recompile, reverse engineer, modify, or create

derivative works of this Software.

2. You may make one copy of this Software for

backup purposes only.

3. You are not permitted to reverse engineer

this software.

4. This EULA allows you to install one copy of

this Software on one piece of Equipment.

2. Disclaimers

To the extent not prohibited by law, in no

event shall Anritsu be liable for personal

injury, or any incidental, special, indirect or

consequential damages whatsoever,

including, without limitation, damages for

loss of profits, loss of data, business

interruption or any other commercial

damages or losses, arising out of or related

to your use or inability to use this Software.

3. Limitation of Liability

a. If a fault (bug) is discovered in this Software,

preventing operation as described in the

operation manual or specifications whether

or not the customer uses this software as

described in the manual, Anritsu shall at its

own discretion, fix the bug, or exchange the

software, or suggest a workaround,

free-of-charge. However, notwithstanding

the above, the following items shall be

excluded from repair and warranty.

i) If this Software is deemed to be used for

purposes not described in the operation

manual or specifications.

ii) If this Software is used in conjunction with

other non-Anritsu-approved software.

iii) Recovery of lost or damaged data.

iv) If this Software or the Equipment has been

modified, repaired, or otherwise altered

without Anritsu's prior approval.

v) For any other reasons out of Anritsu's direct

control and responsibility, such as but not

limited to, natural disasters, software virus

infections, etc.

b. Expenses incurred for transport, hotel, daily

allowance, etc., for on-site repairs by Anritsu

engineers necessitated by the above faults

shall be borne by you.

c. The warranty period for faults listed in

article 3a above covered by this EULA shall

be either 6 months from the date of purchase

of this Software or 30 days after the date of

repair, whichever is longer.

vii

4. Export Restrictions

You may not use or otherwise export or

re-export directly or indirectly this Software

except as authorized by Japanese and

United States law. In particular, this

software may not be exported or re-exported

(a) into any Japanese or US embargoed

countries or (b) to anyone on the Japanese or

US Treasury Department's list of Specially

Designated Nationals or the US Department

of Commerce Denied Persons List or Entity

List. By using this Software, you warrant

that you are not located in any such country

or on any such list. You also agree that you

will not use this Software for any purposes

prohibited by Japanese and US law,

including, without limitation, the

development, design and manufacture or

production of missiles or nuclear, chemical or

biological weapons of mass destruction.

5. Termination

Anritsu shall deem this EULA terminated if

you violate any conditions described herein.

This EULA shall also be terminated if the

conditions herein cannot be continued for

any good reason, such as violation of

copyrights, patents, or other laws and

ordinances.

6. Reparations

If Anritsu suffers any loss, financial or

otherwise, due to your violation of the terms

of this EULA, Anritsu shall have the right to

seek proportional damages from you.

7. Responsibility after Termination

Upon termination of this EULA in

accordance with item 5, you shall cease all

use of this Software immediately and shall

as directed by Anritsu either destroy or

return this Software and any backup copies,

full or partial, to Anritsu.

8. Dispute Resolution

If matters of dispute or items not covered by

this EULA arise, they shall be resolved by

negotiations in good faith between you and

Anritsu.

9. Court of Jurisdiction

This EULA shall be interpreted in

accordance with Japanese law and any

disputes that cannot be resolved by

negotiation described in Article 8 shall be

settled by the Japanese courts.

viii

Cautions against computer virus infection

•Copying files and data

Only files that have been provided directly from Anritsu or generated

using Anritsu equipment should be copied to the instrument.

All other required files should be transferred by means of USB or

CompactFlash media after undergoing a thorough virus check.

•Adding software

Do not download or install software that has not been specifically

recommended or licensed by Anritsu.

•Network connections

Ensure that the network has sufficient anti-

virus security protection in

place.

CE Conformity Marking

Anritsu affixes the CE conformity marking on the following product(s) in

accordance with the Council Directive 93/68/EEC to indicate that they

conform to the EMC and LVD directive of the European Union (EU).

CE marking

1. Product Model

Software: MX269018A Analog Measurement Software

2. Applied Directive and Standards

When the MX269018A Analog Measurement Software is installed in the

MS2830A, the applied directive and standards of this unit conform to

those of the MS2830A main frame.

PS: About main frame

Please contact Anritsu for the latest information on the main frame

types that MX269018A can be used with.

C-Tick Conformity Marking

Anritsu affixes the C-Tick mark on the following product(s) in accordance

with the regulation to indicate that they conform to the EMC framework of

Australia/New Zealand.

C-Tick marking

1. Product Model

Software: MX269018A Analog Measurement Software

2. Applied Directive and Standards

When the MX269018A Analog Measurement Software is installed in the

MS2830A, the applied directive and standards of this unit conform to

those of the MS2830A main frame.

PS: About main frame

Please contact Anritsu for the latest information on the main frame

types that MX269018A can be used with.

Autres manuels pour MS2830A

Table des matières

Autres manuels Anritsu Instrument de mesure

Anritsu

Anritsu MS2840A-040 Manuel utilisateur

Anritsu

Anritsu Network Master Series Manuel utilisateur

Anritsu

Anritsu MS2690A Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2711D Manuel utilisateur

Anritsu

Anritsu MS2691A Manuel utilisateur

Anritsu

Anritsu MP1632C Manuel utilisateur

Anritsu

Anritsu MT8852B Manuel utilisateur

Anritsu

Anritsu MS2024A Manuel d'utilisation et d'entretien

Anritsu

Anritsu Field Master MS2070A-703 Manuel utilisateur

Anritsu

Anritsu VNA Master MS203 A Series Manuel utilisateur

Anritsu

Anritsu MT1100A Network Master Flex Manuel utilisateur

Anritsu

Anritsu MS2830A Manuel utilisateur

Anritsu

Anritsu Field Master Pro MS2090A Manuel du propriétaire

Anritsu

Anritsu MS462 Series Manuel utilisateur

Anritsu

Anritsu MW9076 Series Manuel utilisateur

Anritsu

Anritsu 3656C W1 Manuel utilisateur

Anritsu

Anritsu MU196060A Manuel utilisateur

Anritsu

Anritsu Network Data Analyzer MD6430A Manuel utilisateur

Anritsu

Anritsu VectorStar ME7838 4 Series Manuel utilisateur

Anritsu

Anritsu MS27101A-IBCM Manuel utilisateur

Anritsu

Anritsu MS46122A/B-010 Manuel utilisateur

Anritsu

Anritsu MS27100A Manuel utilisateur

Anritsu

Anritsu Microwave Site Master S820E Manuel utilisateur

Anritsu

Anritsu MW9076 Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur