Anritsu MD1230A Manuel utilisateur

Document No.: M-W1927BE-1.0

Measurement Solutions

ANRITSU CORPORATION

MD1230A

Data Quality Analyzer

Service Manual

First Edition

To ensure that this equipment is used safely, impor-

tant safety items are also explained in the MD1230A

Data Quality Analyzer Operation Manual. This

manual explains important service items related to

service. Read both the operation manual and this

manual, and keep both with the equipment.

iiii

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following

safety symbols to indicate safety-related information. Insure that you clearly understand the meanings of the sym-

bols BEFORE using the equipment.

Some or all of the following five symbols may not be used on all Anritsu equipment. In addition, there may be other

labels attached to products which are not shown in the diagrams in this manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Insure that you clearly understand the meanings of the symbols

and take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated sym-

bolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is indicat-

ed symbolically in or near the circle.

This indicates warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MD1230A

Data Quality Analyzer

Service Manual

17 October 2001 (First Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

iiiiii

iii

WARNING

1. ALWAYS refer to the operation manual when working near locations

at which the alert mark shown on the left is attached. If the operation,

etc., is performed without heeding the advice in the operation manual,

there is a risk of personal injury. In addition, the equipment perfor-

mance may be reduced.

Moreover, this alert mark is sometimes used with other marks and de-

scriptions indicating other dangers.

2. Laser radiation warning

•NEVER look directly into the cable connector on the equipment nor

into the end of a cable connected to the equipment. If laser radia-

tion enters the eye, there is a risk of injury.

•Laser Radiation Markings on a following page show the Laser

Safety label attached to the equipment near the cable connector.

3. When supplying power to this equipment, connect the accessory 3-pin

power cord to a 3-pin grounded power outlet. If a grounded 3-pin

outlet is not available, before supplying power to the equipment, use a

conversion adapter and ground the green wire, or connect the frame

ground on the rear panel of the equipment to ground. If power is

supplied without grounding the equipment, there is a risk of receiving

a severe or fatal electric shock.

4. This equipment cannot be repaired by the user. DO NOT attempt to

open the cabinet or to disassemble internal parts. Only Anritsu-

trained service personnel or staff from your sales representative with a

knowledge of electrical fire and shock hazards should service this

equipment. There are high-voltage parts in this equipment present-

ing a risk of severe injury or fatal electric shock to untrained personnel.

In addition, there is a risk of damage to precision parts.

Anritsu Corporation will not accept liability for any injuries sustained as

a result of opening the equipment covers.

5. This equipment should be used in the correct position. If the cabinet

is turned on its side, etc., it will be unstable and may be damaged if it

falls over as a result of receiving a slight mechanical shock.

Repair

Falling Over

For Safety

iviv

WARNING

6. When replacing the battery, use the specified battery and insert it with

the correct polarity. If the wrong battery is used, or if the battery is

inserted with reversed polarity, there is a risk of explosion causing

severe injury or death.

7. DO NOT short the battery terminals and never attempt to disassemble

it or dispose of it in a fire. If the battery is damaged by any of these

actions, the battery fluid may leak.

This fluid is poisonous.

DO NOT touch it, ingest it, or get in your eyes. If it is accidentally in-

gested, spit it out immediately, rinse your mouth with water and seek

medical help. If it enters your eyes accidentally, do not rub your eyes,

irrigate them with clean running water and seek medical help. If the

liquid gets on your skin or clothes, wash it off carefully and thoroughly.

8. This instrument uses a Liquid Crystal Display (LCD); DO NOT subject

the instrument to excessive force or drop it. If the LCD is subjected

to strong mechanical shock, it may break and liquid may leak.

This liquid is very caustic and poisonous.

DO NOT touch it, ingest it, or get in your eyes. If it is ingested acci-

dentally, spit it out immediately, rinse your mouth with water and seek

medical help. If it enters your eyes accidentally, do not rub your eyes,

irrigate them with clean running water and seek medical help. If the

liquid gets on your skin or clothes, wash it off carefully and thoroughly.

Replacing Battery

Battery Fluid

ＬＣＤ

ＬＣＤＬＣＤ

ＬＣＤ

For Safety

CAUTION

1. Before changing the fuses, ALWAYS remove the power cord from the

poweroutlet and replace the blown fuses. ALWAYS use new fuses of

the type and rating specified on the fuse marking on the rear panel of

the cabinet.

Fuse label :

F10A indicate a normal fusing type fuse.

There is risk of receiving a fatal electric shock if the fuses are replaced

with the power cord connected.

2. Keep the power supply and cooling fan free of dust.

•Clean the power inlet regularly. If dust accumulates around the

power pins, there is a risk of fire.

•Keep the cooling fan clean so that the ventilation holes are not ob-

structed. If the ventilation is obstructed, the cabinet may overheat

and catch fire.

3. NEVER input a signal of more than the indicated value between the

measured terminal and ground. Input of an excessive signal may

damage the equipment.

Changing Fuse

Cleaning

Check Terminal

For Safety

vivi

WARNING

Optical output safety is assured by the correct operation of the optical

output warning means. If the light emission from optical output warning

means cannot be confirmed at power-On or optical switch On before us-

ing the optical output, the warning means may be faulty. In this case,

don’t use the equipment and ask repair to Anritsu Corp. or the represen-

tative.

Class 1, Class 2 and Class 3 indicates the degree of danger of the laser

radiation outlined below as defined by JIS C60825-1, IEC60825-1 and

21CFR1040.10.

Class 1 Safe laser presenting no danger when used according to des-

ign specifications.

Class 2 Laser radiating in 400 to 700 nm wavelength range. In prin-

cipal, this class of laser is not safe, but the danger to the eyes

is eliminated by the eye avoidance reaction including the blink

response.

Class 3A Laser radiating in 400 to 700 nm wavelength range. The

danger to the eyes is eliminated by the eye avoidance reaction

including the blink response. For lasers radiating at other

wavelengths, the degree of danger to the naked eyes is not

greater than Class 1.

Class 3B The eyes will be damaged if direct laser radiation enters the

eyes. Normally there is no danger if the diffused beam is ob-

served.

This equipment is a Class-1 Laser Product as defined by the relevant

safety specifications (JIS C60825-1, IEC60825-1, 21CFR1040.10).

Class 1 is indicated at the rear panel of this equipment.

LASER SAFETY

Laser Radiation Markings

For Safety

vii

viivii

vii

CAUTION

This equipment uses a fluoridation graphite lithium battery to back-up the

memory. This battery must be replaced by a service engineer when it

has reached the end of its useful life; contact the Anritsu sales section or

your nearest representative.

Note: The battery used in this equipment has a maximum useful life of 7

years. It should be changed before this period has elapsed.

Floppy disk drive may be damaged by the dust and dirt. For maintaining

the correct operation, perform cleaning the magnetic head, periodically.

This instrument uses parts with operating times or power-on time life

span These parts must be replaced at the customers expense even if

within the guaranteed period described in Warranty in the beginning of

this manual.

Pay attention to the life-span of parts used in continuous long-time op-

eration.

Changing memory

back-up battery

Floppy disk drive

Life time of parts

viii

viiiviii

viii

Equipment Certificate

Anritsu Corporation certifies that this equipment was tested before ship-

ment using calibrated measuring instruments with direct traceability to

public testing organizations recognized by national research laboratories

including the Electrotechnical Laboratory, the National Research Labora-

tory of Metrology and the Communications Research Laboratory, and was

found to meet the published specifications.

Anritsu Warranty

Anritsu Corporation will repair this equipment free-of-charge if a mal-

function occurs within 1 year after shipment due to a manufacturing fault,

provided that this warranty is rendered void under any or all of the fol-

lowing conditions.

•The fault is outside the scope of the warranty conditions described in

the operation manual.

•The fault is due to mishandling, misuse, or unauthorized modification

or repair of the equipment by the customer.

•The fault is due to severe usage clearly exceeding normal usage.

•The fault is due to improper or insufficient maintenance by the cus-

tomer.

•The fault is due to natural disaster including fire, flooding, earthquake,

etc.

•The fault is due to use of non-specified peripheral equipment,

peripheral parts, consumables, etc.

•The fault is due to use of a non-specified power supply or in a non-

specified installation location.

In addition, this warranty is valid only for the original equipment pur-

chaser. It is not transferable if the equipment is resold.

Anritsu Corporation will not accept liability for equipment faults due to

unforeseen and unusual circumstances, nor for faults due to mishandling

by the customer.

Anritsu Corporation Contact

If this equipment develops a fault, contact Anritsu Corporation or its rep-

resentatives at the address at the end of paper-edition manual or the

separate file of CD-edition manual.

ixix

Notes On Export Management

This product and its manuals may require an Export License/Approval by

the Government of the product's country of origin for re-export from your

country.

Before re-exporting the product or manuals, please contact us to confirm

whether they are export-controlled items or not.

Trademark

Windows is a registered trademark of Microsoft Corporation US.

Disposing of Product

This equipment uses chemical compound semiconductors including

arsenide, and a lithium battery. At the end of its life, the equipment

should be recycled or disposed properly according to the local disposal

regulations.

Software License Agreement

Please read this Software License Agreement before using the accom-

panying software program (hereafter this software).

You are authorized to use this software only if you agree to all the terms of

this License.

By opening the sealed package containing this software, you are agreeing

to be bound by the terms of this License.

If you do not agree to these terms, return the unopened software package

to Anritsu Corporation (hereafter Anritsu).

1. License

(1) This License gives you the right to use this software on one computer

system.

(2) To use this software on one computer system, this License allows you

to make one copy of this software on the storage device of your com-

puter system.

(3) You must obtain a site license to use this software on more than one

computer system even if such computer systems are not operating

simultaneously.

2. Copyright

(1) Although you are licensed to use this software, Anritsu retains the

(2) Although you have purchased this software, rights other than those

specified in this License are not transferred to you.

(3) You may not print, copy, modify, create derivative works, incorporate

in other software programs, decompile or disassemble this software

in whole or in part, without obtaining prior written permission from

Anritsu.

3. Copying

Notwithstanding item (3) of section 2 above, you may make one copy of

this software for backup purposes only. In this case, you may only use

either the backup copy or the original copy of this software.

4. Termination

(1) Anritsu will deem this License to be automatically terminated if you

fail to comply with any provision of this License. Upon termination,

you will lose all rights to this software.

(2) Either party (Anritsu or yourself) to this Software License Agree-

ment may terminate this Agreement by giving 1 months notice in

writing to the other party.

(3) Upon termination of this License for any reason, you must either

immediately destroy this software and related documentation, or re-

turn it to Anritsu.

Table des matières

Autres manuels Anritsu Instrument de mesure

Anritsu

Anritsu MS2690A Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2721B Manuel utilisateur

Anritsu

Anritsu MU182020A Manuel utilisateur

Anritsu

Anritsu MW9076 Series Manuel utilisateur

Anritsu

Anritsu PowerMaster MA245 A Series Manuel utilisateur

Anritsu

Anritsu MS2691A Manuel utilisateur

Anritsu

Anritsu MS2665C Manuel utilisateur

Anritsu

Anritsu MS2690A Manuel utilisateur

Anritsu

Anritsu Microwave Site Master S820E Manuel utilisateur

Anritsu

Anritsu MS2690 Manuel utilisateur

Anritsu

Anritsu VectorStar ME7838 4X Series Manuel utilisateur

Anritsu

Anritsu CMA 5000 - UTA Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Anritsu

Anritsu MS9740A Manuel utilisateur

Anritsu

Anritsu MT9083B2 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Anritsu

Anritsu MS2665C Manuel utilisateur

Anritsu

Anritsu Site Master S120A Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2711D Manuel utilisateur

Anritsu

Anritsu VectorStar ME7838E4 Manuel utilisateur

Anritsu

Anritsu Field Master Pro MS2090A Manuel utilisateur

Anritsu

Anritsu FieldMaster MS2080A Manuel utilisateur

Anritsu

Anritsu MP1632C Manuel utilisateur

Anritsu

Anritsu VectorStar MS4640A Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur