Anritsu BTS Master MT8221B Manuel utilisateur

BTS Master

User Guide

MT8221B and MT8222B

The High Performance Handheld Base Station Analyzer

User Guide

BTS Master

MT8221B and MT8222B

High Performance Handheld Base Station Analyzer

Appendix A provides a list of supplemental documentation for the

BTS Master features and options. The documentation set is

available as PDF files on the documentation disc and the Anritsu

Web site.

Anritsu Company

490 Jarvis Drive

Morgan Hill, CA 95037-2809

USA

http://www.anritsu.com

Part Number: 10580-00207

Revision: E

Published: March 2014

WARRANTY

The Anritsu products listed on the title page are warranted against defects in materials and

workmanship for one year from the date of shipment.

Anritsu’s obligation covers repairing or replacing products which prove to be defective during the

warranty period. Buyers shall prepay transportation charges for equipment returned to Anritsu for

warranty repairs. Obligation is limited to the original purchaser. Anritsu is not liable for consequential

damages.

LIMITATION OF WARRANTY

The foregoing warranty does not apply to Anritsu connectors that have failed due to normal wear. Also,

the warranty does not apply to defects resulting from improper or inadequate maintenance by the

Buyer, unauthorized modification or misuse, or operation outside of the environmental specifications of

the product. No other warranty is expressed or implied, and the remedies provided herein are the

Buyer’s sole and exclusive remedies.

DISCLAIMER OF WARRANTY

DISCLAIMER OF WARRANTIES. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE

LAW, ANRITSU COMPANY AND ITS SUPPLIERS DISCLAIM ALL WARRANTIES, EITHER

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH REGARD TO THE

PRODUCT. THE USER ASSUMES THE ENTIRE RISK OF USING THE PRODUCT. ANY LIABILITY

OF PROVIDER OR MANUFACTURER WILL BE LIMITED EXCLUSIVELY TO PRODUCT

REPLACEMENT.

NO LIABILITY FOR CONSEQUENTIAL DAMAGES. TO THE MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, IN NO EVENT SHALL ANRITSU COMPANY OR ITS SUPPLIERS BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER

(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,

BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY

LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THE PRODUCT, EVEN IF ANRITSU

COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME

STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY

NOT APPLY TO YOU.

TRADEMARK ACKNOWLEDGMENTS

VxWorks is a registered trademark, and WindML is a trademark of Wind River Systems, Inc.

BTS Master is a trademark of Anritsu Company.

NOTICE

Anritsu Company has prepared this manual for use by Anritsu Company personnel and customers as a

guide for the proper installation, operation and maintenance of Anritsu Company equipment and

computer programs. The drawings, specifications, and information contained herein are the property of

Anritsu Company, and any unauthorized use or disclosure of these drawings, specifications, and

information is prohibited; they shall not be reproduced, copied, or used in whole or in part as the basis

for manufacture or sale of the equipment or software programs without the prior written consent of

Anritsu Company.

UPDATES

Updates, if any, can be downloaded from the Anritsu Website at:

http://www.anritsu.com

For the latest service and sales contact information in your area, please visit:

http://www.anritsu.com/contact.asp

CE Conformity Marking

Anritsu affixes the CE Conformity marking onto its conforming products in accordance with

Council Directives of The Council Of The European Communities in order to indicate that

these products conform to the EMC and LVD directive of the European Union (EU).

C-tick Conformity Marking

Anritsu affixes the C-tick marking onto its conforming products in accordance with the

electromagnetic compliance regulations of Australia and New Zealand in order to indicate

that these products conform to the EMC regulations of Australia and New Zealand.

Notes On Export Management

This product and its manuals may require an Export License or approval by the government

of the product country of origin for re-export from your country.

Before you export this product or any of its manuals, please contact Anritsu Company to

confirm whether or not these items are export-controlled.

When disposing of export-controlled items, the products and manuals need to be broken or

shredded to such a degree that they cannot be unlawfully used for military purposes.

Mercury Notification

This product uses an LCD backlight lamp that contains mercury. Disposal may be regulated

due to environmental considerations. Please contact your local authorities for disposal or

recycling information.

BTS Master UG PN: 10580-00207 Rev. E Safety-1

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu

Company uses the following symbols to indicate safety-related information. For your own

safety, please read the information carefully before operating the equipment.

Symbols Used in Manuals

Safety Symbols Used on Equipment and in Manuals

The following safety symbols are used inside or on the equipment near operation locations to

provide information about safety items and operation precautions. Ensure that you clearly

understand the meanings of the symbols and take the necessary precautions before operating

the equipment. Some or all of the following five symbols may or may not be used on all

Anritsu equipment. In addition, there may be other labels attached to products that are not

shown in the diagrams in this manual.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates a compulsory safety precaution. The required operation is indicated

symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

Danger

This indicates a very dangerous procedure that could result in serious injury

or death, or loss related to equipment malfunction, if not performed properly.

Warning This indicates a hazardous procedure that could result in light-to-severe

injury or loss related to equipment malfunction, if proper precautions are not

taken.

Caution

This indicates a hazardous procedure that could result in loss related to

equipment malfunction if proper precautions are not taken.

Safety-2 PN: 10580-00207 Rev. E BTS Master UG

For Safety

Warning Always refer to the operation manual when working near locations at

which the alert mark, shown on the left, is attached. If the operation,

etc., is performed without heeding the advice in the operation

manual, there is a risk of personal injury. In addition, the equipment

performance may be reduced. Moreover, this alert mark is sometimes

used with other marks and descriptions indicating other dangers.

Warning

When supplying power to this equipment, connect the accessory

3-pin power cord to a 3-pin grounded power outlet. If a grounded

3-pin outlet is not available, use a conversion adapter and ground the

green wire, or connect the frame ground on the rear panel of the

equipment to ground. If power is supplied without grounding the

equipment, there is a risk of receiving a severe or fatal electric shock.

Warning

This equipment can not be repaired by the operator. Do not attempt to

remove the equipment covers or to disassemble internal

components. Only qualified service technicians with a knowledge of

electrical fire and shock hazards should service this equipment.

There are high-voltage parts in this equipment presenting a risk of

severe injury or fatal electric shock to untrained personnel. In

addition, there is a risk of damage to precision components.

Caution

Electrostatic Discharge (ESD) can damage the highly sensitive

circuits in the instrument. ESD is most likely to occur as test devices

are being connected to, or disconnected from, the instrument’s front

and rear panel ports and connectors. You can protect the instrument

and test devices by wearing a static-discharge wristband.

Alternatively, you can ground yourself to discharge any static charge

by touching the outer chassis of the grounded instrument before

touching the instrument’s front and rear panel ports and connectors.

Avoid touching the test port center conductors unless you are

properly grounded and have eliminated the possibility of static

discharge.

Repair of damage that is found to be caused by electrostatic

discharge is not covered under warranty.

Warning This equipment is supplied with a rechargeable battery that could potentially

leak hazardous compounds into the environment. These hazardous

compounds present a risk of injury or loss due to exposure. Anritsu

Company recommends removing the battery for long-term storage of the

instrument and storing the battery in a leak-proof, plastic container. Follow

the environmental storage requirements specified in the product data sheet.

Ce manuel convient aux modèles suivants

Autres manuels Anritsu Instrument de mesure

Anritsu

Anritsu Spectrum Master MS2721B Manuel utilisateur

Anritsu

Anritsu BTS Master MT8220T Manuel du propriétaire

Anritsu

Anritsu 54100A Series Instructions d'installation et d'utilisation

Anritsu

Anritsu Microwave Site Master S820E Manuel utilisateur

Anritsu

Anritsu MT8820A Manuel utilisateur

Anritsu

Anritsu Site Master S114C Manuel utilisateur

Anritsu

Anritsu MT8820A Manuel utilisateur

Anritsu

Anritsu MT1000A Network Master Pro Manuel utilisateur

Anritsu

Anritsu LMR Master Manuel utilisateur

Anritsu

Anritsu MD1230B Manuel utilisateur

Anritsu

Anritsu IQproducer XG-PHS Manuel utilisateur

Anritsu

Anritsu VectorStar ME7838A Manuel utilisateur

Anritsu

Anritsu MS2690 Manuel utilisateur

Anritsu

Anritsu S331E Manuel utilisateur

Anritsu

Anritsu MS2690A Manuel d'installation

Anritsu

Anritsu Spectrum Master MS2711E Manuel utilisateur

Anritsu

Anritsu Lightning 37 E Series Manuel utilisateur

Anritsu

Anritsu VectorStar ME7838 4X Series Manuel utilisateur

Anritsu

Anritsu Site Master S332D Manuel utilisateur

Anritsu

Anritsu ShockLine MS46322A Series Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2711D Manuel utilisateur

Anritsu

Anritsu IQ Fiber Master Manuel utilisateur

Anritsu

Anritsu MX269017A Manuel utilisateur

Anritsu

Anritsu SQA-R MP1900A Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur