Analog Devices EVAL-ADPD6000 Manuel utilisateur

User Guide | EVAL-ADPD6000

UG-2033

Evaluating the ADPD6000 Multimodal Sensor Front End

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT

WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | 1 of 20

FEATURES

►Board supports ADPD6000 population

►4 separately driven LEDs included: 1 green LED at the center, 1

red LED, and 2 infrared LEDs

►Four channels of PD input: two channels with single PD, and two

channels with double PD

►Works with the VSM Client evaluation software allowing

►Time domain graphing and logging

►Selection of supported functions, including PPG, BIA, and

ECG

►Real-time data display with the various combinations of the

functions

EVALUATION KIT CONTENTS

►EVAL-ADPD6000Z evaluation board

►EVAL-VSMUCZ microcontroller board

ADDITIONAL EQUIPMENT NEEDED

►USB to Type-C cable

►3.7 V battery

►Electrode board

►Soft cable to connect EVAL-ADPD6000Z and EVAL-VSMUCZ

►Wrist strap

ONLINE RESOURCES

►ADPD6000 data sheet

►VSM Client software (available on EVAL-ADPD6000 product

page)

GENERAL DESCRIPTION

This user guide describes the operation of the EVAL-ADPD6000Z

demonstration kit, which is an evaluation module for the

ADPD6000.

The ADPD6000 is a fully integrated analog front end (AFE) for

wearable vital signal monitoring (VSM) devices. The key functions

of the ADPD6000 include photoplethysmography (PPG), electrocar-

diography (ECG), and body impedance analysis (BIA).

The demonstration kit includes both software and hardware. The

EVAL-ADPD6000Z can evaluate the AFE feature and verify the

system design based on the AFE. According to the requirements of

the application, the user can use a cable connection or Bluetooth

connection to establish communication between the PC and the

EVAL-ADPD6000Z.

This user guide also describes the example configuration of the

different functions of the ADPD6000.

For full details on the ADPD6000, see the ADPD6000 data sheet,

which must be consulted in conjunction with this user guide when

using the EVAL-ADPD6000Z.

EVALUATION BOARD PHOTOGRAPH

Figure 1. EVAL-ADPD6000Z

User Guide EVAL-ADPD6000

TABLE OF CONTENTS

analog.com Rev. 0 | 2 of 20

Features................................................................ 1

Evaluation Kit Contents......................................... 1

Additional Equipment Needed............................... 1

Online Resources.................................................. 1

General Description...............................................1

Evaluation Board Photograph................................1

Preparation and Setup...........................................3

EVAL-ADPD6000Z Components........................3

PCB Connection.................................................3

Software Installation.............................................. 5

Power on the System............................................ 6

Power On–Cable Connection.............................6

Power On–Bluetooth Connection.......................6

Add Device via Bluetooth................................... 6

VSM Client ............................................................8

Find the Device On VSM Client .........................8

Configure the Device........................................10

Receive the Data.............................................. 11

Human Measurement.......................................... 13

PPG Measurement...........................................13

ECG Measurement...........................................13

BIA Measurement.............................................14

Evaluation Board Schematics and Artwork......... 15

Notes................................................................... 20

REVISION HISTORY

4/2022—Revision 0: Initial Version

User Guide EVAL-ADPD6000

PREPARATION AND SETUP

analog.com Rev. 0 | 3 of 20

EVAL-ADPD6000Z COMPONENTS

Figure 2 shows the components needed for evaluation.

Figure 2. EVAL-ADPD6000Z Demonstration Kit Components

PCB CONNECTION

Take the following steps to establish the printed circuit board (PCB)

connection:

1. Connect the battery to the connector on the EVAL-VSMUCZ

(see Figure 3. Ensure that the S1 switch is off.

Figure 3. Battery Connected to EVAL-VSMUCZ

2. Connect the EVAL-VSMUCZ to the EVAL-ADPD6000Z (see

Figure 4 and Figure 5). Ensure the EVAL-VSMUCZ and EVAL-

ADPD6000Z have the same number of pins, and that the pin

numbers match.

Figure 4. EVAL-VSMUCZ Connection

Figure 5. EVAL-ADPD6000 Connection

3. For ECG or BIA measurement, connect the EVAL-ADPD6000Z

to the electrodes on the electrode board as follows:

►For ECG measurement, connect P3 to Electrode 1, P4 to

Electrode 2, and P6 to Electrode 3. Leave Electrode 4

unconnected (see Figure 6).

►For BIA measurement, connect P3 to Electrode 1, P4 to

Electrode 2, P6 to Electrode 3, and P5 to Electrode 4 (see

Figure 7).

Note that the BIA connection can also be used for ECG meas-

urement.

User Guide EVAL-ADPD6000

PREPARATION AND SETUP

analog.com Rev. 0 | 4 of 20

Figure 6. ECG Connection

Figure 7. BIA Connection

Figure 8 shows the EVAL-ADPD6000Z kit connection after setup.

Figure 8. Demonstration Kit After Setup

User Guide EVAL-ADPD6000

SOFTWARE INSTALLATION

analog.com Rev. 0 | 5 of 20

The VSM Client software is the graphical user interface (GUI)

used for the EVAL-ADPD6000Z demonstration kit. The VSM Client

software is available on the EVAL-ADPD6000Z product page.

Take the following steps to install VSM Client:

1. Download and launch the VSM Client installer.

2. Read the software license agreement and click I Agree (see

Figure 9).

Figure 9. License Agreement

3. Select Only for me and click Next > (see Figure 10). Do not

select Anyone who uses this computer (all users), as this

option can cause the installation to suspend or fail.

Figure 10. Choose Installation Options

4. Click Browse... to choose the installation location and then click

Next > (see Figure 11).

Figure 11. Choose Installation Location

5. When the installation is complete, click Finish to complete the

installation process (see Figure 12).

Figure 12. Installation Complete

User Guide EVAL-ADPD6000

POWER ON THE SYSTEM

analog.com Rev. 0 | 6 of 20

After preparing the hardware and installing the software, the EVAL-

ADPD6000Z is ready to power on.

POWER ON–CABLE CONNECTION

Connect the USB to Type-C cable from the PC to J5 on the

EVAL-VSMUCZ to power on the EVAL-VSMUCZ automatically. The

two indicator lights on the EVAL-VSMUCZ (DS1 and DS4) turn on.

If the S1 switch labeled in Figure 13 is set to on, the battery is

charged by the PC. Figure 13 shows the cable connection.

Figure 13. Cable Connection

POWER ON–BLUETOOTH CONNECTION

Take the following steps to power on the system without the USB

cable:

1. On the EVAL-VSMUCZ, set the S1 switch labeled in Figure 13

to on. The standalone DS1 indicator LED labeled in Figure 13

turns on.

2. Press (for about two seconds) the S3 button on the EVAL-

VSMUCZ to power on the system. The two indicator lights on

the EVAL-VSMUCZ (DS1 and DS4) turn on.

ADD DEVICE VIA BLUETOOTH

Take the following steps to add the EVAL-VSMUCZ via Bluetooth

(these steps are shown using Windows® 10):

1. Click the Bluetooth Devices icon in the system tray and select

Add a Bluetooth Device (see Figure 14).

Figure 14. Add a Bluetooth Device

2. The Settings window opens (see Figure 15). Under Bluetooth

& other devices, click Add Bluetooth or other device.

Figure 15. Add Bluetooth Device from Settings Window

3. The Add a device window opens (see Figure 16). Select

Bluetooth.

User Guide EVAL-ADPD6000

POWER ON THE SYSTEM

analog.com Rev. 0 | 7 of 20

Figure 16. Choose Bluetooth Device Type

4. Select the EVAL-VSMUCZ from the list of devices (in this

example, Figure 17 shows the device as B8-7425A2). The

device is now connected (see Figure 18).

Figure 17. Select EVAL-VSMUCZ

Figure 18. Device Connected

After adding the EVAL-VSMUCZ, two Bluetooth serial ports appear

in the Device Manager window: Standard Serial over Bluetooth

link (COM10) and Standard Serial over Bluetooth link (COM11)

(see Figure 19). The user selects one of these two ports in the VSM

Client software.

Figure 19. Device Manager

User Guide EVAL-ADPD6000

VSM CLIENT

analog.com Rev. 0 | 8 of 20

FIND THE DEVICE ON VSM CLIENT

Take the following steps to find the device on the VSM Client

software:

1. After installing VSM Client, power on the EVAL-ADPD6000Z

and launch VSM Client.

2. Click Click to connect in the start interface of VSM Client (see

Figure 20).

Figure 20. Start Interface of VSM Client

3. In the Hardware Connection pane, select the communication

(COM) port according to the connection method, as follows:

►If using a Bluetooth connection, two ports are available. In

the example shown in Figure 21, these ports are COM50

Microsoft BTHENUM and COM58 Microsoft BTHENUM.

Select one of the two ports. If the following steps cannot

be completed successfully with the selected port, select a

different port.

►If using a cable connection, only one port is available (see

Figure 22). In the example shown in Figure 22, the port is

COM11 Microsoft USB.

The COM serial port numbers shown are examples only. Refer

to the Device Manager for the COM serial port numbers.

Figure 21. Bluetooth Connection COM Ports

Figure 22. Cable Connection COM Port

4. Toggle the connection switch to Connect (see Figure 23).

When connected, a Success to connect target! pop-up ap-

pears at the top of the VSM Client window (see Figure 24), and

the Click to connect button changes to display Connected

6000. To disconnect the device, toggle the connection switch to

Disconnect. The following pop-up messages can appear if the

connection is unsuccessful:

►Failed to connect target: undefined. Please try to recon-

nect. If this pop-up appears (see Figure 25), select another

COM port and reconnect.

►Fail to get firmware version!. If this pop-up appears (see

Figure 26), the firmware version may not match the software

version. Update the firmware in the kit. For details on updat-

ing the firmware, see the EVAL-ADPD6000Z product page.

Figure 23. Toggle Connection Switch

Figure 24. Connection Successful

Figure 25. Failed to Connect Target Error

Figure 26. Failed to Get Firmware Version Error

5. From the Type dropdown menu, select one of three functions:

ECG, PPG, or BIOZ (see Figure 27). Click Select to enter the

configuration interface.

User Guide EVAL-ADPD6000

VSM CLIENT

analog.com Rev. 0 | 9 of 20

Figure 27. Select Function

User Guide EVAL-ADPD6000

VSM CLIENT

analog.com Rev. 0 | 10 of 20

CONFIGURE THE DEVICE

Take the following steps to configure the device:

1. Click Load cfg File in the configuration interface of VSM Client

to load a basic configuration file (see Figure 28). To export the

current configuration file, click Export cfg File to save the script

in the configuration file folder (see Figure 30). To change the

loaded .dcfg file, click Reset before continuing.

Figure 28. Configuration Interface

2. Click Click/Drag a .dcfg file to load to open the .dcfg file in

the Load Configuration window (see Figure 29). According

to the application or measurement conditions, the user can

choose the following initial configurations from the C:\Analog

Devices\VSM Client\VSM_Client\Cfg\ADPD6000 location:

►ADPD6000_BIOZ_slotABCDEF_MS6_Testing: BIA magni-

tude and phase measurement

►ADPD6000_ECG_Testing: ECG channel signal measure-

ment

►ADPD6000_PPG_Testing_slotA_Peak_SNR_one_led: PPG

peak signal-to-noise (SNR) test using LED1A

►ADPD6000_PPG_Testing_slotA_Peak_SNR_two_led: PPG

peak SNR test using LED1A and LED2A

►ADPD6000_PPG_Testing_slotA_SNR_85dB: PPG 85 dB

SNR test using LED2A

►ADPD6000_PPG_Testing_slotA_SNR_95dB: PPG 95dB

SNR test using LED1A

The configuration files in the configuration file folder may differ

from those shown in Figure 30.

Figure 29. Choose Configuration File

Figure 30. Configuration File Folder

3. Click Load (see Figure 31) to load the configuration file.

Figure 31. Load Configuration

4. After loading the configuration file, the Highlevel Configura-

tion tab shows the current device data (see Figure 32). This

tab shows the most used controls, which can be configured. To

reset the data, click Reset.

Figure 32. Highlevel Configuration Tab

5. To read or write an individual register, click the Register Con-

figuration tab. To check a register, enter the address in the

change a register, enter the value in the Register Value field

and click Write (see Figure 34). See the ADPD6000 data sheet

for the detailed values of the registers.

Table des matières

Autres manuels Analog Devices Matériel informatique

Analog Devices

Analog Devices ADuCM322 Manuel utilisateur

Analog Devices

Analog Devices EZ-KIT Lite ADSP-21364 Guide de l'utilisateur

Analog Devices

Analog Devices AD9843A Manuel utilisateur

Analog Devices

Analog Devices ADAV4622 Manuel utilisateur

Analog Devices

Analog Devices ADSP-21369 EZ-KIT Lite Manuel utilisateur

Analog Devices

Analog Devices EVAL-ADF4152HVEB1Z Manuel utilisateur

Analog Devices

Analog Devices ADICUP3029 Manuel utilisateur

Analog Devices

Analog Devices ADF7021-V Manuel utilisateur

Analog Devices

Analog Devices MicroConverter ADuC832 Manuel utilisateur

Analog Devices

Analog Devices EVAL-ADA4570SDZ Manuel utilisateur

Analog Devices

Analog Devices Linear LTM 4700 Manuel utilisateur

Analog Devices

Analog Devices Linear ADI Power LTC3310-1 Manuel utilisateur

Analog Devices

Analog Devices AD7194 Manuel utilisateur

Analog Devices

Analog Devices ADSP-BF561 EZ-KIT Lite Manuel utilisateur

Analog Devices

Analog Devices ADSP-BF53x Blackfin Manuel de service

Analog Devices

Analog Devices LINEAR DC2672A-A Guide de configuration rapide

Analog Devices

Analog Devices DC3089A Manuel utilisateur

Analog Devices

Analog Devices EZ-Board ADSP-21489 Manuel utilisateur

Analog Devices

Analog Devices CN-0506 Manuel utilisateur

Analog Devices

Analog Devices ADSP-21261 SHARC Guide d'application

Analog Devices

Analog Devices ADP1046A Manuel utilisateur

Analog Devices

Analog Devices ADSP-BF53x EZ-Extender 1 Manuel utilisateur

Analog Devices

Analog Devices EVAL-ADAU1860 Manuel utilisateur

Analog Devices

Analog Devices SHARC ADSP-21367 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur