AMI EMB-B75B Manuel utilisateur

Page 1 of 12

22166955

REV. C

Kit Core Upgrade-EMB-B75B Without Modem

Kit #22166905

These instructions outline the procedures to install the EMB-B75B motherboard

into your existing Computer Core Chassis. There may be unused parts in this kit

depending on the style of Core being upgraded.

Tools Required

1/4” and 11/32” nut driver, #2 Philips Screw driver

Parts Included with this Kit:

Item # Part Number Description Quantity

1 40924214 Computer Board Assy EMB-B75B 1

2 22219001 SATA Hard Drive U.S. 1

3 40980801 Bracket Hard Drive Tray Replacement 1

4 40980802 Bracket SATA Mounting Adapter 1

5 22144401 Cover Computer Card (Not Shown) 1

6 34072201 Cover PSI Low Profile (Not Shown) 1

7 34052405 Power On/Reset CBA 1

8 22132276 Cable Assembly ON/Reset 1

9 34037946 Harness Assembly ATX Power 1

10 22132277 Cable Assembly DB9 1

11 EC0358-01 Cable SATA Data 1

12 EC0359-01 Harness SATA Power 1

13 21889250 DB9 Hardware (Not Shown) 1

14 80402304 #6-32 x ¼” Phillips (Not Shown) 4

15 80351604 #4-40 x ¼” Phillips (Not Shown) 4

16 28277901 M3 x 6 Phillips (Not Shown) 4

17 70800106 Tie Wrap (Not Shown) 2

18 22190901 Bracket Mounting (Hard Drive) 1

These Instructions

NOTE: If you are installing this kit into a Blue View Core Computer assembly, you will need to

order one additional harness. Order part number 22132280.

Installation Instructions

Page 2 of 12

22166955

REV. C

Figure 1

Page 3 of 12

22166955

REV. C

Caution: When installing this EMB-B75B motherboard, care should be taken to avoid

static discharges that can damage the motherboard. The motherboard installation should

be done on a static dissipative mat along with a grounding wrist strap.

Removing the Motherboard and ON/OFF reset board

1. Turn the jukebox off and unplug the power cord from the wall outlet.

2. Open the jukebox door and disconnect all the harnessing to the Computer Core. Note where

the cables plug into the Computer Core Assembly for later reinstallation. Remove the

Computer Core from the jukebox.

3. Rowe has six major Computer Cores as shown in Figure 2. Each Core has slightly different

variations (fans, lights, etc.) depending on your jukebox model. It is important to note these

variations and ensure they are connected after the motherboard installation.

Figure 2

4. Remove all necessary components and covers to access the motherboard. Unplug and remove

all ribbon cables from the motherboard. Disconnect all of the ATX power supply connections

and the IDE Cable from the hard drive. Remove the modem card and its PCI cover (if

present) from the motherboard; they will not be reused. Replacement PCI Covers (Items #5

and #6) are provided in this kit.

5. Remove the old ON/OFF reset board (340524XX) and the DB9 cable assembly from its

mounting bracket; they will not be reused. Save the mounting bracket and hardware for later

use.

6. Remove the seven screws that secure the motherboard to the core chassis. The motherboard

and the front panel will not be reused; save the screws for later use.

Page 4 of 12

22166955

REV. C

Installing the EMB-B75B Motherboard and 34052405 ON/OFF reset board

7. Insert the front panel into position and carefully align the new motherboard (Item #1) with

the four existing studs on the computer core chassis. Secure the motherboard with four of the

seven screws removed in step #6.

8. Mount the ON/OFF reset board 34052405 (Item #7) and the DB9 Cable Assembly 22132277

(Item #10) and its hardware (Item #13) to your previously removed mounting bracket and

reinstall into your Computer Core. Connect the ON/RESET cable 22132276 (Item #8) into

the keyed 10-pin header of the ON/RESET circuit board assembly. Refer to Figure 3.

9. Figure 3 shows all the electrical connections to your new motherboard. Connect the two

ribbon cables as shown in Figure 3. Connect the 20-pin connector to the 24-pin housing on

the motherboard. If your ATX power supply does not have the 4-pin connector, use the ATX

Power Harness 34037946 (Item #9) provided with this kit. If you have a chassis fan, connect

it to a spare 4-pin connector of the ATX power supply. Refer to Figure 3.

Figure 3

20-PIN ATX POWER

SUPPLY

CONNECTION

DB9 SERIAL CABLE 22132277

Note: FOR BLUE VIEW CORE

USE SERIAL CABLE 22132280

(not included in this kit)

SATA/POWER

CONNECTION

EC0359-01

SATA/DATA

CONNECTIONS

EC0358-01

ON/RESET CABLE

CONNECTIONS

22132276

4-PIN ATX

POWER

SUPPLY

CONNECTION

Page 5 of 12

22166955

REV. C

Assembling the SATA Hard Drive with the Adapter Mounting Bracket

10. Secure the SATA hard drive 22219001 (Item #2) to the SATA Mounting Adapter Bracket

40980802 (Item #4) using the four M3 x 6 metric screws 28277901 (Item #16) as shown in

Figure 4.

Figure 4

The following pages describe installing the hard drive in the different computer core models.

Continue to the step # relating to the core you are reworking.

221674XX Step 11

611765XX Step 14

61171001 Step 15

61171002 Step 16

70260-1A Step 17

View Core Step 18

Connecting the SATA Hard Drive to the 221674XX Series Computer Core

11. Disconnect the 4-pin power cable and IDE cable from the hard drive tray. Remove the four

screws that mount the hard drive tray. The tray will not be reused, but you must save the

screws for use in the following step. See Figure 4.

Figure 5

HARD

DRIVE

M3X6 METRIC

SCREWS

(TWO ON

EITHER SIDE)

ADAPTOR

BRACKET

REMOVE

POWER AND

IDE CABLES

REMOVE THE

SCREWS TWO

ON EITHER

SIDE

Page 6 of 12

22166955

REV. C

12. Mount the replacement Hard Drive Tray Bracket 40980801 (Item #3) on the inside cover of

your computer core using the four screws previously removed. Ensure the bracket properly

covers the front opening. Thread the four 6-32 x ¼” screws 80402304 (Item #14) into the

mounting adapter leaving approximately 1/16-inch gap. Insert the screw heads through the

four keyholes on the hard drive tray replacement bracket and slide the hard drive down to

secure it into the slots. Tighten the four screws. See Figure 6.

13. Connect the SATA/Power Cable EC0359-01 (Item #12) to a 4-pin connector of the ATX

power supply. Connect the SATA/Data Cable EC0358-01 (Item #11) to the motherboard.

Refer to Figure 3 for motherboard connections. Continue with step #19.

Figure 6

HARD DRIVE

REPLACEMENT

TRAY

FOUR

KEYHOLES

SATA/POWER

22132253 SATA/DATA

CABLE

22132252

Page 7 of 12

22166955

REV. C

Connecting the SATA Hard Drive to the 611765XX Series Computer Core.

14. Disconnect the power and IDE Cables from the hard drive. Loosen the thumbscrew and

remove the hard drive from the housing; it will not be reused. Insert the hard drive adapter

bracket and hard drive assembled in step #10 into the housing and secure with the four

fasteners. Reassemble the housing to the computer core and connect the SATA/Power Cable

EC0359-01 (Item #12) to a 4-pin connector of the ATX power supply. Connect the

SATA/Data Cable EC0358-01 (Item #11) to the motherboard. Refer to Figure 3 for

motherboard connections. Continue with step #19.

Figure 7

SATA/DATA

AND

SATA/POWER

ASSEMBLED

HARD DRIVE

ATX POWER

SUPPLY

CONNECTION

Page 8 of 12

22166955

REV. C

Connecting the SATA Hard Drive to the 61171001 Computer Core

15. Disconnect the power and IDE Cables from the hard drive. Loosen the four screws and

remove the hard drive and bracket, it will not be reused. Attach the hard drive adapter bracket

and hard drive (assembled in step #10) to the new Hard Drive Mounting Bracket 22190901

(Item #18) by aligning it with the slots and securing it with four screws 80402304 (Item #14).

Connect the SATA/Power Cable EC0359-01 (Item #12) to a 4-pin connector of the ATX

power supply. Connect the SATA/Data Cable EC0358-01 (Item #11) to the motherboard

(refer to Figure 3). Connect the SATA Data and SATA Power cables to the hard drive as

shown in Figure 8. Attach the hard drive assembly to the computer core. Refer to Figure 3 for

motherboard connections. Reassemble the remaining components to the computer core.

Continue with step #19.

Figure 8

SATA/DATA

AND

SATA/POWER

HARD

DRIVE

ASSEMBLY

HARD DRIVE

MOUNTING

BRACKET

ATX

POWER

SUPPLY

Page 9 of 12

22166955

REV. C

Connecting the SATA Hard Drive to the 61171002 Computer Core

16. Disconnect the power and IDE Cables from the hard drive. Remove the two thumbscrews

and the two hard drive brackets from the hard drive (the hard drive will not be reused).

Attach these two brackets to the hard drive adapter bracket and hard drive assembled in step

#10 and secure with the same four screws. Reassemble the hard drive assembly to the

computer core. Connect the SATA/Power Cable EC0359-01 (Item #12) to a 4-pin connector

of the ATX power supply. Connect the SATA/Data Cable EC0358-01 (Item #11) to the

motherboard. Refer to Figure 3 for motherboard connections. Continue with step #19.

Figure 9

SATA/DATA

AND POWER

CONNECTIONS

ATX

POWER

SUPPLY

Page 10 of 12

22166955

REV. C

Connecting the SATA Hard Drive to the 70260-1A Series Rock-Ola Computer

Core

17. Disconnect the power and IDE Cables from the hard drive. Remove the four thumbscrews

from the hard drive (the hard drive will not be reused). Install the four thumbscrews into the

adapter bracket and hard drive assembled in step #10. Reassemble the hard drive assembly to

the Computer Core as shown in Figure 10. Connect the SATA/Power Cable EC0359-01

(Item #12) to a 4-pin connector of the ATX power supply. Connect the SATA/Data Cable

EC0358-01 (Item #11) to the motherboard. Refer to Figure 3 for the motherboard

connections. Continue with step #19.

Figure 10

HARD

DRIVE

ASSEMBLY

SATA/DATA

AND POWER

CONNECTIONS

Table des matières

Autres manuels AMI Carte mère

AMI

AMI Ecast View B75B Manuel utilisateur

AMI

AMI Kit-CJE B75B Manuel utilisateur

AMI

AMI MB960 Manuel utilisateur

AMI

AMI MB941 Manuel utilisateur

AMI

AMI MI982 Manuel utilisateur

AMI

AMI MI946F Manuel utilisateur

AMI

AMI IMBM-Q87A Manuel utilisateur

AMI

AMI MI956 Manuel utilisateur

AMI

AMI 410 Manuel

AMI

AMI MI890 Manuel utilisateur

AMI

AMI EMB-Q87A Manuel utilisateur

AMI

AMI Mark IV Screamer Manuel utilisateur

AMI

AMI MI987 Manuel utilisateur

AMI

AMI M920 Series Manuel utilisateur

AMI

AMI ATX-H310A Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur