Alpha Alpha CB Boiler Manuel utilisateur

Installation Instructions

Alpha CB/C/SY Boiler

90° and 45° Flue Bends

Concentric (60/100) Flue System

1. GENERAL

a. The flue system must be installed in accordance with BS 5440:1;1990.

b. The boiler must be installed in accordance with the Installation instructions supplied with the boiler.

c. Each 90° bend is equivalent to 1 metre of flue length.

Each 45° bend is equivalent to 0.5 metre of flue length.

d. For vertical flue applications refer to separate instructions.

e. For horizontal flue applications ensure that there is a slight downward slope towards the terminal.

f. Use the following methods to determine the correct length of horizontal flue required:-

For rear exit flue L = B + 175 mm

For side exit flue L = B + C + 185 mm (min. side clearance required is 5 mm)

Where L = Required length of flue

B = Finished wall thickness

C = Distance from inside wall to the side of the boiler, e.g. C = E + F

g. Note:Forrearorsideflue,cuta110mmdiameterhole(orusea107mmcoredrill)inthewallisrequiredforflueassembly.

h. Refer to the flue options and ensure the flue length does not exceed the maximum equivalent length of 4 metre, or

3 metre when fitted to an Alpha C23/27.

Fig. 1 - Horizontal side flue options

L = B + C + E + 185 mmL = B + C + 185 mm

Front

Kit Part No. 6.1000330 Kit Part No. 6.1000340

Lmax = equivalent flue length of 4 m (except C23/27, Lmax = 3 m)

Compiled and designed by Publications 2000, Tel (01670) 356211

These guidelines have been carefully prepared but we reserve the right to

alter the specification at any time in the interest of product improvement.

03/04/D131

Part No. 6.9174352

2. CUTTING THE FLUE DUCTS TO LENGTH

Refer to the Installation instructions supplied with the boiler.

a. With all the ducts assembled together and one 90° bend fitted to the boiler (see Fig. 1), cut to the following lengths:-

Rear flue Outer air duct length = finished wall thickness + 135 mm

Inner flue duct length = finished wall thickness + 172 mm

Side flue Outer air duct length = finished wall thickness + the distance from the inside wall to the side of the

boiler + 145 mm

Inner flue duct length = finished wall thickness + the distance from the inside wall to the side of the

boiler + 182 mm

Note: When cutting the flue ducts ensure that all cuts are square and burr free.

b. When using a flue bend within the flue length (see Fig. 2), prepare and cut the flue ducts as follows:-

a. Place the bend in the required position and cut/prepare the inner and outer ducts for fitting to one end of the bend.

b. Assemble the bend onto the ducts, as shown in Fig. 4, using the clamp and seal provided.

c. Position the remaining flue in the required position and mark the inner and outer ducts for the connection to the

other end of the bend.

d. Cut/prepare the ducts and assemble them to the bend, as shown in Fig. 4, using the clamp and seal supplied.

Fig. 4

Fig. 2 - Horizontal side flue options

L = B + E + F + 185 mm + (90° bend = 1 metre) L = B + C + 185 mm + (2 x 45° bends = 1 metre)

Top

Fig. 3 - Horizontal flue options

Lmax = equivalent flue length of 4 m (except C23/27, Lmax = 3 m)

Alpha Therm Limited.

Nepicar House, LondonRoad,Wrotham Heath,

Sevenoaks, Kent TN15 7RS

Tel: 0870 3001 964

email: info@alphatherm.co.uk

website: www.alpha-innovation.co.uk

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Alpha Chaudière

Alpha

Alpha Alpha CD18S Guide de l'utilisateur

Alpha

Alpha E-Tec 25R Guide de l'utilisateur

Alpha

Alpha Alpha C23 Guide de l'utilisateur

Alpha

Alpha CD Easy-Flue Series Manuel utilisateur

Alpha

Alpha Alpha HE25 Manuel utilisateur

Alpha

Alpha CD90S Guide de l'utilisateur

Alpha

Alpha InTec 50CS Guide de l'utilisateur

Alpha

Alpha InTec 40GS2 Guide de l'utilisateur

Alpha

Alpha InTec2 20SE Guide de l'utilisateur

Alpha

Alpha E-Tec Plus 28 Guide de l'utilisateur

Alpha

Alpha 26C Guide de l'utilisateur

Alpha

Alpha Alpha CD32 Manuel utilisateur

Alpha

Alpha Alpha 240X Manuel utilisateur

Alpha

Alpha Alpha HE25 Manuel utilisateur

Alpha

Alpha Alpha CombiMax 350 Guide de l'utilisateur

Alpha

Alpha Alpha CD24 Guide de l'utilisateur

Alpha

Alpha 240eco Manuel utilisateur

Alpha

Alpha SolarSmart 90 Instructions d'installation

Alpha

Alpha Alpha CombiMax 350 Feuille d'instructions

Alpha

Alpha Alpha C23 Manuel utilisateur

Alpha

Alpha InTec2 25XE Guide de l'utilisateur

Alpha

Alpha SolarSmart 90 Guide de l'utilisateur

Alpha

Alpha Evoke 28 Guide de l'utilisateur

Alpha

Alpha 41 532 05 Guide de l'utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur