Alpha Alpha CB Boiler Manuel utilisateur

Installation Instructions

Alpha CB/C/SY Boiler

Vertical FlueTerminal Assembly

Twin Pipe (80 mm) Flue System

(Kit Part No. 6.1000369)

KIT CONTENTS

1. GENERAL

a. The flue system must be installed in accordance with BS 5440:1:1990.

b. The boiler must be installed in accordance with the installation instructions supplied with the boiler and the twin

pipe flue instructions supplied with the boiler conversion kit.

c. The vertical flue terminal assembly is equivalent to 1.0 m of flue length.

d. Refer to the vertical flue options in Fig. 1 and ensure that the flue length (H) does not exceed the equivalent of

7.0 m.

e. Each 45° bend is equivalent to 0.5 m of length of flue and no more than four bends must be used in each flue

exhaust or air inlet duct.

Note: 90° bends must not be used with the vertical flue.

f. Additional flue/air ducting is available in 1.0 m lengths for extending the flue up to a maximum equivalent flue

length of 7.0 m.

g. The vertical terminal may be connected directly to the boiler via the conversion kit. However, under no

circumstances must the terminal be shortened in length.

h. To determine the total length (A) of flue/air ducting required (refer to Fig. 1).

Measure the distance (X) from the top of the boiler side panel to the weathering slate position and subtract 640

mm for the terminal assembly, i.e. C = X - 640 mm

A = 2 x C + (50 mm for each connection in straight ducting).

Compiled and designed by Publications 2000, Tel (01670) 356211 08/04/D131

Fig. 1

H = Equivalent length of flue or air duct

The Vertical terminal assembly is equivalent to 1.0 m of flue length and each 45° bend is equivalent to 0.5 m of flue length.

Note: 90° bends must not be used with the vertical flue.

2. INSTALLATION

Refer to the Twin Pipe Flue installation instructions supplied with the boiler conversion kit (Part No. 6.1000368).

a. Refer to Fig. 1 for positioning of the vertical terminal in the roof.

b. To enable direct connection of the flue and air ducts to the terminal the duct centres must be 120 mm apart.

c. At the required position cut a hole and/or remove tiles so that there is at least a 170 mm diameter hole in the roof.

Ensure there is at least a 25 mm gap between the outer duct and any combustible material.

d. Fit a weathering slate, suitable for a 125 mm outside diameter flue, over the hole in the roof. A suitable weathering

slate (Part No. 6.1000380) is available from Alpha Therm Ltd.

e. Fit the terminal assembly into the weathering slate and place it in position, ensuring the minimum distances given in

Fig. 1 are maintained.

f. After assembly of the ducts to the terminal, ensure it is not possible to disengage any part of the flue assembly.

Check that the weathering slate is fitted correctly and ensure that the flue assembly is supported at roof level using

suitable brackets.

These instructions have been carefully prepared but we reserve the right to

alter the specification at any time in the interest of product improvement.

Alpha Therm Limited.

Nepicar House,LondonRoad,WrothamHeath,

Sevenoaks, Kent TN15 7RS

Tel: 0870 3001 964

email: info@alphatherm.co.uk

website: www.alpha-innovation.co.uk

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Alpha Chaudière

Alpha

Alpha ARES Pro 150 Guide de l'utilisateur

Alpha

Alpha Alpha C23 Manuel utilisateur

Alpha

Alpha CD Easy-Flue Series Manuel utilisateur

Alpha

Alpha Alpha CB50 Boiler Manuel utilisateur

Alpha

Alpha Alpha 500E Manuel utilisateur

Alpha

Alpha Alpha CD32 Manuel utilisateur

Alpha

Alpha Eco Manuel utilisateur

Alpha

Alpha SolarSmart 90 Instructions d'installation

Alpha

Alpha al357i-b Manuel utilisateur

Alpha

Alpha Pro Tec 115 Guide de l'utilisateur

Alpha

Alpha Alpha CombiMax 350 Feuille d'instructions

Alpha

Alpha InTec12S Manuel utilisateur

Alpha

Alpha Alpha CB24 Manuel utilisateur

Alpha

Alpha ARES 150 Tec Guide de l'utilisateur

Alpha

Alpha Alpha 240X Manuel utilisateur

Alpha

Alpha Alpha CD25C Manuel utilisateur

Alpha

Alpha Alpha CD18S Manuel utilisateur

Alpha

Alpha Alpha InTec 12SNG Guide de l'utilisateur

Alpha

Alpha Alpha CD25X Guide de l'utilisateur

Alpha

Alpha Alpha CB24 Manuel utilisateur

Alpha

Alpha 280E Manuel utilisateur

Alpha

Alpha 26C Manuel utilisateur

Alpha

Alpha E-Tec Plus 28 Guide de l'utilisateur

Alpha

Alpha Alpha CD50 Manuel utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur