Alpha Alpha CD35C Manuel utilisateur

18 litres/minute from

acombi?

FlowSmart.

Astep-by-step installation guide.

STEP 1 STEP 2 STEP 3

STEP 4 STEP 5 STEP 6

Using a spirit level, tape the GasSaver and

PremierPack templates to wall. Mark all positions as

indicated on wall, drill holes and add rawlplugs. Mark

flue position and drill hole.

Screw PremierPack, GasSaver hanging bracket and

top fixing bolt assembly to wall.The boiler and

GasSaver can now be simply hung whenever you are

ready.

Drill hole in wall and push Expansion Relief Valve pipe

through. Pull back so that the rubber grommet

completes a seal, mark off and cut to required length.

Removetails from boiler and screw to PremierPack.

Measure, cut, bend and fit GasSaver mains inlet/outlet

pipework to PremierPack using the pipe clip plate.

Complete any other necessary pipework and fit using

pipe clips where required.

Complete anysoldering that is necessary Position thermal store where required, and fit

washers plus tails to connections shown on pipework

label on top of store

The perfect combination

18 steps to 18 litres/minute

FlowSmart system v 200L unvented cylinder at flow rate 18 litres/minute

Time (minutes)

Te m p °C at flow rate 18L/min

DHW output °C

200L unvented cylinder

DHW output °C

FlowSmart 25L store

02 4 6 8 10 12 14 16 18 20

DHW output °C

FlowSmart 50L store

FlowSmart system v 200L unvented cylinder at flow rate 18 litres/minute

Its thermal store recharges in just 5-7

minutes, compared to the 45 minutes a

200 litre cylinder can take to replenish

from empty.

The small thermal store takes up much

less space than a cylinder, enabling

FlowSmart to be more easily sited. If

required, the entire system can even be

installed together in a cupboard.

This, along with a limited pipework

requirement, means installation of

FlowSmartis also quicker and simpler.

LESS GAS USED*

FlowSmart uses up to 25% less gas to provide DHW than a system boiler with a 200 litre unvented store

and consumes less electricity.

By incorporating a GasSaver and small thermal store, FlowSmart allows a combi boiler to deliver a flow rate of 18

litres of hot water per minute, at 50ºC or above, for up to 30 minutes – more than three times longer than a typical

system boiler set-up.Together with its superior energy efficiency and ease of installation, this makes FlowSmart the

perfect combination.

STEP 10 STEP 11 STEP 12

STEP 13 STEP 14 STEP 15

STEP 16 STEP 17 STEP 18

Lift boiler on to PremierPack and fasten connections

from PremierPack to boiler.

Fit GasSaver flue clamp and lower GasSaver on to

flue turret. Secure GasSaver using top fixing bolts and

adjust to level.Tighten screws on GasSaver flue

turret.

Connect the pipework to GasSaver and fit flue pipe.

Position and fit junction box, fuse spur, 2-channel

timer and room thermostat.

Removethermal store thermostat panel. Cut

insulation material as required and remove. Wire up

cylinder thermostat and fit into cut hole and secure

using the fastening supplied.

Lower boiler control panel and removeterminal

block cover. Replace 3-core power chord with 4-core

cable to provide a switched liveconnection at

terminal one.

Replace terminal block and cover, push control panel

back into place and screw down. Fit pipe cover tray

to complete installation.

Adjust all settings on controls, thermostats and timers

according to installation instructions and homeowner’s

requirements. Commission the system, carefully

following the commissioning guidelines provided.

Completed installation.

STEP 7 STEP 8 STEP 9

Install blending valve between mains water supply

and hot outlet of thermal store.The blended outlet

connects to the boiler cold water inlet.

Fit expansion vessel to primary return pipe of

thermal store, using the compression T-piece

provided.

Fit Y-Plan mid position valve to primary flow, thermal

store primary inlet connection and heating circuit.

The complete system solution

For further information call us on 01732 783000

or visit www.alpha-innovation.co.uk

Nepicar House, London Road,Wrotham Heath, Kent TN15 7RS

est data assessed by TUV NEL Ltd

CD35C boiler

Acompact SEDBUK ‘A’ rated

condensing boiler with fully-modulating

output of up to 35kW.

GasSaver

Captures and stores heat from boiler

flue gases, using it to pre-heat cold mains

water before it enters the boiler.

Thermal store

Uses heat from the primary system to

further raise the temperature of the

water pre-heated by the GasSaver.

What’s included

How FlowSmart works

When there is a demand for DHW, mains cold water flows into the GasSaver, where its temperature is raised using

heat reclaimed from boiler flue gases.

Cold Water Inlet

Cold Water Outlet

DHW Outlet

Flow Rate 18L/min

GasSaver

CD35C

Combi

60˚C and below

80˚C and below

30˚C

55˚C

Blending Valve

25L or 50L

Primary Store

Flow

Return

This pre-heated water then passes

through a copper coil heat exchanger in

the thermal store, where it is heated

further by surrounding hot water from

the primarysystem.

The water then passes through a

blending valve, where it is controlled to

30ºC, before entering the boiler.

With less work to do to raise the

water’stemperature, the boiler is able

to satisfy heavy DHW demands for long

periods, without detrimental effect to

flow rate.

Ce manuel convient aux modèles suivants

Autres manuels Alpha Chaudière

Alpha

Alpha 240eco Guide de l'utilisateur

Alpha

Alpha ARES 150 Tec Guide de l'utilisateur

Alpha

Alpha Alpha CD18S Manuel utilisateur

Alpha

Alpha Alpha CD50 Guide de l'utilisateur

Alpha

Alpha Alpha CombiMax 350 Manuel utilisateur

Alpha

Alpha ARES 440 Tec Guide de l'utilisateur

Alpha

Alpha Alpha CD25X Guide de l'utilisateur

Alpha

Alpha Alpha C23 Guide de l'utilisateur

Alpha

Alpha Alpha CB Boiler Manuel utilisateur

Alpha

Alpha Alpha HE25 Guide de l'utilisateur

Alpha

Alpha Alpha 240XP Guide de l'utilisateur

Alpha

Alpha Alpha CombiMax 350 Guide de l'utilisateur

Alpha

Alpha 30C Guide de l'utilisateur

Alpha

Alpha E-Tec 28 Manuel utilisateur

Alpha

Alpha DS 24 TF Manuel du produit

Alpha

Alpha Alpha CB50 Boiler Guide de l'utilisateur

Alpha

Alpha Alpha Plus DH Units Mode d’emploi

Alpha

Alpha Alpha CB Boiler Manuel utilisateur

Alpha

Alpha Alpha CD25C Guide de l'utilisateur

Alpha

Alpha InTec2 20SE Guide de l'utilisateur

Alpha

Alpha Alpha 240 Boiler Range Manuel d'instructions et de sécurité

Alpha

Alpha Alpha CD32 Manuel utilisateur

Alpha

Alpha Evoke 28 Guide de l'utilisateur

Alpha

Alpha Ocean Style FF Manuel utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur