Allo RemoteControl NICE Era TOUCH HSTS2FR Manuel utilisateur
NICE HSTS2FR Era TOUCH Touchscreen
families:
INSTRUCTIONS
Visit our Website. www.alloremotecontrol.com
To perform the initial start-up proceed as follows (fig. 3):
01. Open the lid: press on point 1 and then push the bottom upwards (point 2);
02. Check that memory board A is there; if not insert it in the suitable slot (point 3);
03. Insert the batteries, observing the polarity shown (point 4);
04. Replace the bottom.
Upon start-up, the main screen appears on the display (fig. 4) which has three icons
from where you can access the respective sub-menus.
To browse through the menu and the sub-menus, just touch the screen in
correspondence to the desired icon.
Various screen models are available as well as several browsing icons. Before
proceeding, get familiar with the screens and icons by consulting figures 4 and 5. Note
–Some of the icons in this manual are only visible if the HSTS2 is used as an interface
to control the HSCU2 series alarm control units. The icons associated with scenarios or
command groups are shown below by way of example. The icons related to scenarios
or command groups will be displayed only if associated during the configuration.
Visit our website: www.Alloremotecontrol.com
.
INSTALLATION:
Visit our website: www.Alloremotecontrol.com
Visit our website: www.Alloremotecontrol.com
Visit our website: www.Alloremotecontrol.com
USING THE TOUCH SCREEN KEYPAD AS 4 REMOTE CONTROL FOR AUTOMATION UNITS:
USING THE TOUCH SCREEN KEYPAD AS 4 REMOTE CONTROL FOR AUTOMATION
UNITS
The touch screen keypad can command the automation units of the Nice range (gates,
doors, curtains, shutters, lights, etc.) compatible with the FLOR encoding (compatible with
the Opera system), up to a maximum of 99 automation units. Each of them can be
assigned a specific name (e.g.: “Kitchen”), the category you wish the automation unit to
belong to (e.g.: “Blinds”) and the commands to be associated (e.g.: “Up, Stop, Down”). It
is possible to define: - groups: to command automation units of the same type at the
same time; - scenarios: to manage various automation units and alarm system; - timer:
for the automatic execution of groups or scenarios
Creating an automation unit in the touch screen:
01. Turn on the touch screen keypad and touch the “Domotics” icon in the main screen
(fig. 6);
02. Touch the icon “Automations” (fig. 7);
03. Scroll through the icons using the scroll bar to the side;
04. Touch and then “Automations”;
05. In the appearing list select “Automation 01” and in the following screen (fig. 8) touch:
“
Name” to write the name of the automation unit (e.g. “Entrance Gate”); “Type” to select
one of the three types the automation unit to be commanded belongs to (GATES - BLINDS
- LIGHTS); “Commands” to associate the commands envisaged for the automation unit to
be commanded (STANDARD - CUSTOM 1 - CUSTOM 2
06. Confirm with “OK”.
The one just created will be shown in the automation unit list. Repeat the procedure to
create the other automation units. The automation units created until now will be available
in the lists associated with the icons which characterise their type (fig. 9):
Visit our website: www.Alloremotecontrol.com
Table des matières
Autres manuels Allo RemoteControl écran tactile
Manuels écran tactile populaires d'autres marques
Elecro Engineering
Elecro Engineering Poolsmart Plus Instructions d'installation
Johnson Controls
Johnson Controls IQ4 HUB Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET2270L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET1002L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems 3201L Manuel utilisateur
Duratec
Duratec S15 Manuel utilisateur
