Allen-Bradley 2100-ENET Manuel utilisateur

Installation Instructions

Quick Start Guide for Configuring an E3

Plus EtherNet/IP Adapter

Catalog Numbers

2100-ENET

Topic Page

Important User Information 2

Additional Resources 3

Components 3

Status Indicators 4

Introduction 4

Set the IP Network Address 4

Install EDS File 7

Logix Controller I/O Messaging 9

2Quick Start Guide for Configuring an E3 Plus EtherNet/IP Adapter

Rockwell Automation Publication 2100-IN090A-EN-P - February 2012

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the

Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation

sales office or online at http://www.rockwellautomation.com/literature/) describes some important differences between solid-state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for

solid-state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of

this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or

application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual

use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software

described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is

prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous

environment, which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death,

property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard and recognize the

consequences.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to alert people that

dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to alert people that

surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

Quick Start Guide for Configuring an E3 Plus EtherNet/IP Adapter 3

Rockwell Automation Publication 2100-IN090A-EN-P - February 2012

Additional Resources

These documents contain additional information concerning related products from Rockwell

Automation.

You can view or download publications at http://www.rockwellautomation.com/literature/. To

order paper copies of technical documentation, contact your local Allen-Bradley distributor or

Rockwell Automation sales representative.

Components

Components of the Adapter

Resource Description

Ethernet Design Considerations

Reference Manual, publication ENET-RM001

Provides explanation of the following Ethernet concepts:

•Overview

•Network Layout and Components

•Network Infrastructure Devices

•Network Infrastructure Features

•Protocol

Industrial Automation Wiring and Grounding

Guidelines, publication 1770-4.1

Provides general guidelines for installing a Rockwell Automation industrial

system.

Product Certifications website, http://www.ab.com Provides declarations of conformity, certificates, and other certification

details.

Item Part Description

1 Status Indicators Four status indictors for the DPI, the adapter, and network connection.

3 Ethernet Connector An RJ-45 connector for the Ethernet cable. The connector is CAT-5 compliant to

ensure reliable data transfer on 100Base-TX Ethernet connections.

4Quick Start Guide for Configuring an E3 Plus EtherNet/IP Adapter

Rockwell Automation Publication 2100-IN090A-EN-P - February 2012

Status Indicators

The adapter uses four status indicators to report its operating status.

Status Indicators

Introduction

The E3 Plus EtherNet/IP Adapter module is a linking device that lets users connect an E3 or E3

Plus Solid State Overload, 825-P Motor Protection System, or IntelliVAC+ module directly to

an EtherNet/IP network. This document explains the basic steps needed to configure the E3

Plus EtherNet/IP Adapter module.

Set the IP Network Address

The E3 Plus EtherNet/IP Adapter module ships with Bootstrap Protocol (BOOTP) enabled.

You can set the network Internet Protocol (IP) address by using the BOOTP/DHCP Server

that is provided with RSLinx Classic software. This utility recognized BOOTP-enabled devices

and provides an interface to configure a static IP address for each device.

To assign network parameters via the BOOTP/DHCP utility, perform this procedure.

1. Start the BOOTP/DHCP software.

Item Name Color State Description

1 PORT Green Flashing Normal Operation. The adapter is establishing an I/O connection to the E3 Plus

overload relay. It will turn steady green or red.

2 MOD Steady Normal Operation. The adapter is properly connected and communicating with

the E3Plus overload relay.

3 NET A Green Flashing Normal Operation. The adapter is operating but is not transferring I/O data to a

controller.

4 NET B Steady Normal Operation. The adapter is operating and transferring I/O data to a

controller.

Status Indicators

Quick Start Guide for Configuring an E3 Plus EtherNet/IP Adapter 5

Rockwell Automation Publication 2100-IN090A-EN-P - February 2012

2. Select Tool > Network Settings and enter the subnet mask for the network.

If appropriate for the network, enter the gateway address, primary/secondary server

addresses, and domain name.

3. Click OK.

The Request History panel displays the hardware addresses of devices issuing BOOTP

or DHCP requests.

4. Double-click the MAC address of the adapter to be configured.

The MAC address is printed on the side of the E3 Plus EtherNet/IP Adapter. The

format of the hardware address resembles 00:00:BC:59:72:5A. The New Entry window

appears with the module's Ethernet Address (MAC).

6Quick Start Guide for Configuring an E3 Plus EtherNet/IP Adapter

Rockwell Automation Publication 2100-IN090A-EN-P - February 2012

5. Enter the IP address for the adapter and, if appropriate, enter the host name and an

adapter description.

6. Click OK.

Once the IP address you entered shows up in the Request History panel (you may need

to cycle power to the adapter), this configuration can be permanently assigned to the

adapter.

7. To do so, highlight the adapter in the Relation List panel and click Disable

BOOTP/DHCP.

8. Confirm that the Status panel message reads, ‘[Disable BOOTP] Command successful’.

When the adapter power is recycled, it will use the assigned configuration and will not

issue a BOOTP request. If you do not click Disable BOOTP/DHCP, the adapter clears

the current IP configuration after a power cycle and will again begin sending BOOTP

requests.

Quick Start Guide for Configuring an E3 Plus EtherNet/IP Adapter 7

Rockwell Automation Publication 2100-IN090A-EN-P - February 2012

Install EDS File

Before the E3 Plus EtherNet/IP Adapter module is configured to communicate on an

EtherNet/IP network, it must be registered to the software that configures the network, for

example, RSLinx Classic software. You can registers the adapter by installing an Electronic Data

Sheet (EDS file). For the E3 Plus EtherNet/IP Adapter module, you will install an EDS file for

the device that is connected to the adapter. Use the following procedure to download and

Download EDS file from the EDS Website

The EDS file for the device connected to the E3 Plus EtherNet/IP Adapter module can be found

on at http://www.rockwellautomation.com/resources/eds/.

1. When the webpage for the link above comes up, enter the following information:

2. Find the file that relates to the E3, 825-P, or IntelliVAC+ module that is connected to

the 2100-ENET unit.

3. In the Details & Download column for the device, select Download.

4. Click Save to save the EDS file your personal computer.

After the EDS file has been downloaded, you need to register the EDS file with the software that

configures the EtherNet/IP network. Following these steps to register an EDS file with RSLinx

Classic software.

1. Start the EDS Hardware Installation Tool located at Start->Programs->Rockwell

Software->RSLinx->Tools.

2. Click Add to register a new device.

E3 Plus Overload 825-P IntelliVAC+

Network EtherNet/IP EtherNet/IP EtherNet/IP

Device Type Motor Protector Motor Protector Miscellaneous Type

Bulletin/Catalog No. 2100-ENET 2100-ENET 2100-ENET

Major Revision (Leave Blank) (Leave Blank) (Leave Blank)

Minor Revision (Leave Blank) (Leave Blank) (Leave Blank)

Keyword (Leave Blank) (Leave Blank) (Leave Blank)

8Quick Start Guide for Configuring an E3 Plus EtherNet/IP Adapter

Rockwell Automation Publication 2100-IN090A-EN-P - February 2012

3. Register a single file, browse to the location where the EDS file is located, and click Next.

4. Click Next to accept the installation test results.

Quick Start Guide for Configuring an E3 Plus EtherNet/IP Adapter 9

Rockwell Automation Publication 2100-IN090A-EN-P - February 2012

5. Accept the graphic image by clicking Next.

6. Click Next to register the device.

7. Click Finish to successfully register the module.

Logix Controller I/O Messaging

RSLogix 5000 software is used to configure I/O Messaging between an automation controller

and an E3 Plus EtherNet/IP Adapter module on an EtherNet/IP network. Follow these steps to

configure a Logix controller for I/O Messaging.

1. Right-click on the EtherNet/IP scanner in I/O Configuration and select New Module

to open the Select Module Type window.

2. Select Generic Ethernet Module and click OK.

10 Quick Start Guide for Configuring an E3 Plus EtherNet/IP Adapter

Rockwell Automation Publication 2100-IN090A-EN-P - February 2012

3. Enter a name for the E3 Plus EtherNet/IP Adapter module.

The name creates a tag in RSLogix 5000 software that can be used to read and write data

from the E3 Plus EtherNet/IP Adapter module.

4. Select Data-INT for the Comm Format.

The Comm Format tells RSLogix 5000 software the format of the data. The Data-INT

format represents the data from the E3 Plus EtherNet/IP Adapter module as a field of

16-bit values.

5. Set the Connection Parameters.

I/O data is accessed using Input Instance 100 and Output Instance 103 (for E3

standard) or 105 (for E3 Plus) by default.

IMPORTANT

If the Input and Output Assemblies have already been changed, then those values will need to

be entered instead of the defaults.

Autres manuels pour 2100-ENET

Table des matières

Autres manuels Allen-Bradley Adaptateur

Allen-Bradley

Allen-Bradley 20-COMM-M Modbus/TCP Adapter Manuel utilisateur

Allen-Bradley

Allen-Bradley ArmorPoint DeviceNet 1738-ADN12 Manuel utilisateur

Allen-Bradley

Allen-Bradley 140G Series Manuel utilisateur

Allen-Bradley

Allen-Bradley POINT I/O 1734-AENT Manuel utilisateur

Allen-Bradley

Allen-Bradley 140G Series Manuel utilisateur

Allen-Bradley

Allen-Bradley 1734-AENTRK Manuel utilisateur

Allen-Bradley

Allen-Bradley 2711P-RAAT7 Manuel utilisateur

Allen-Bradley

Allen-Bradley 1734 Manuel utilisateur

Allen-Bradley

Allen-Bradley POINT I/O ControlNet 1734-ACNR Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlNet 1786-BNC2TNC Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 20-COMM-D Manuel utilisateur

Allen-Bradley

Allen-Bradley Compact I/O 1769-ADN DeviceNet Manuel utilisateur

Allen-Bradley

Allen-Bradley 2711R-APK10 Manuel utilisateur

Allen-Bradley

Allen-Bradley Series B Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 20-comm-c FRN 1. Series Manuel utilisateur

Allen-Bradley

Allen-Bradley POINT I/O 1734-ADN Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 525 Manuel utilisateur

Allen-Bradley

Allen-Bradley 140G-G-DRA Manuel utilisateur

Allen-Bradley

Allen-Bradley 2100-ENET Manuel utilisateur

Allen-Bradley

Allen-Bradley D Series Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 525 Manuel utilisateur

Allen-Bradley

Allen-Bradley Flex I/O Manuel utilisateur

Allen-Bradley

Allen-Bradley 22-COMM-E FRN 1.xxx Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 20-COMM-P Manuel utilisateur

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur