Allen-Bradley 2711P-RAAT7 Manuel utilisateur

Installation Instructions

Adapter Kit for PanelView 5000 and PanelView Plus 7 Performance Terminals

Catalog Numbers

2711P-RAAT7, 2711P-RAAK7, 2711P-RAAT10, 2711P-RAAK10, 2711P-RAAT12,

2711P-RAAT12K, 2711P-RAAT15, 2711P-RAAK15

Summary of Changes

This publication contains new and updated information as indicated in the following table.

Topic Page

Summary of Changes 1

Before You Begin 3

Remove the ExistingTerminal From the Panel 4

Drill the Holes for the Adapter Kit 4

Install the Adapter Plate and Backing Plate 6

Prepare to Mount the Terminal 8

Mount the Terminal 9

Finish theTerminal Installation and Apply Power to the Enclosure 11

Drill Template Dimensions 12

Additional Resources 16

Topic Page

Changed PanelView 5500 to PanelView 5000. 1, 2

Added‘Uses Drill Template Cat. No.’column to Adapter Kit Conversion table. 2

Added PanelView 5310 and PanelView 5510 user manual references to step 1. 11

Added PanelView 5310 and PanelView 5510 literature to the Additional Resources table. 16

2Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018

Adapter Kit for PanelView 5000 and PanelView Plus 7 PerformanceTerminals

About This Adapter Kit

This adapter kit includes an adapter plate, gasket, and backing plate that you install into an

existing cutout from a PanelView™ Plus 6 or PanelView standard terminal. Read and understand

these instructions before you begin to install the adapter plate kit and terminal.

See the Adapter Kit Conversion Table on page 2 to determine the adapter kit for your new and

existing terminal.

Adapter Kit Conversion Table

IMPORTANT Do not install a PanelView Plus 7 Standard terminal with this adapter kit. This adapter kit is

only for PanelView 5000 and PanelView Plus 7 Performance terminals.

If you install a PanelView Plus 7 Standard terminal into this adapter kit, you can damage the

standard terminal bezel. Contaminates can also enter the enclosure and damage components

inside the enclosure.

Adapter Kit

Cat. No.

Replace this Existing PanelView Plus 6 or

PanelView Standard Terminal…

With this PanelView

5000 or PanelView

Plus 7 Performance

Terminal

Uses Drill

Template

Cat. No.

2711P-RAAT7 PanelView Plus 6 700 touch screen 6.5-in. touch screen

VIEW-DS002

2711P-RAAK7 • PanelView Plus 6 700 keypad, or keypad with touch screen

• PanelView Standard 600 keypad, or keypad with touch

screen

6.5-in. keypad

with touch screen

2711P-RAAT10 • PanelView Plus 6 1000 touch screen

• PanelView Standard 900 touch screen

10.4-in. touch screen

VIEW-DS003

2711P-RAAK10 • PanelView Plus 6 1000 keypad, or keypad with touch screen

• PanelView Standard 900 keypad

10.4-in. keypad

with touch screen

2711P-RAAT12 • PanelView Plus 6 1250 touch screen

• PanelView Standard 1000 touch screen

12.1-in. touch screen

VIEW-DS004

2711P-RAAT12K • PanelView Plus 6 1250 keypad, or keypad with touch screen

• PanelView Standard 1000 keypad

12.1-in. touch screen

2711P-RAAT15 • PanelView Plus 6 1500 touch screen

• PanelView Standard 1400 touch screen

15-in. touch screen

VIEW-DS005

2711P-RAAK15 • PanelView Plus 6 1500 keypad, or keypad with touch screen

• PanelView Standard 1400 keypad

15-in. keypad

with touch screen

Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018 3

Adapter Kit for PanelView 5000 and PanelView Plus 7 PerformanceTerminals

Adapter Kit Contents

The adapter kits include these parts:

• Adapter plate with threaded studs and gasket

•Backingplate

• Mounting clamps

• Mounting nuts (10-32)

• Drill template

• These installation instructions

Required Tools

These tools are required for installation:

• Clean cloth and a suitable cleanser for dirty panels

• Masking tape and marker or grease pencil

•Scissors

• Center punch and hammer

• Drill and drill bits (pilot drill bit 4.76 mm [3/16 in.], finish drill bit 6.35 mm [1/4 in.])

• Torque wrench and a 3/8-in. socket

•Workgloves

Before You Begin

IMPORTANT Before you install this adapter kit and new terminal, read and understand all of these instructions.

4Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018

Adapter Kit for PanelView 5000 and PanelView Plus 7 PerformanceTerminals

Remove the Existing Terminal From the Panel

Follow these steps to remove the existing terminal from the panel.

1. Remove all power from the enclosure and the terminal.

2. Disconnect all communication cables from the terminal.

3. While holding the terminal, remove the mounting clamps that secure the terminal in the

panel.

4. Remove the terminal from the panel.

Drill the Holes for the Adapter Kit

Follow these steps to drill the holes for the adapter kit by using the drill template included in this

kit.

1. Clean the panel where the drill template will be taped over the existing cutout.

2. Determine which side of the drill template that you need.

ATTENTION: Remove all power from the components in the enclosure and the existing terminal.

Disconnect the communication cables from the terminal.

Failure to remove all power and disconnect communication cables can cause electric shock and

unexpected communication signals to the machinery.

ATTENTION: Be careful when removing the mounting clamps. The terminals can fall out of the

panel after the mounting clamps have been removed. Be sure to hold the terminal in the panel

while you remove the mounting clamps, and then carefully remove the terminal from the panel.

Drill Template for PanelView™ 5000 and PanelView Plus 7 Performance JOTerminals Adapter Kit

For Adapter Kit 2711P-RAAK7

Drill Template for PanelView 5000 and PanelView Plus 7 Performance Terminals

6.5-in. Keypad with Touch Screen Adapter Kit

Replaces these Existing Terminals:

PanelView Plus 6 700 Keypad, or Keypad with Touch Screen

PanelView Standard 600 Keypad, or Keypad with Touch Screen

Printed Actual Size (scale = 1:1)

If you print this drill template from the PDF le, set the paper size on your plotter or printer to 18 x 12 inches.

For dimensions, see the Adapter Kit for PanelView 5000 and PanelView Plus 7 Performance Terminals

Installation Instructions, publication VIEW-IN002, which is shipped with this drill template.

Identifies the new terminals

that can be installed with

this drill template.

Identifies the existing

terminals that can be

replaced with this drill

template.

Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018 5

Adapter Kit for PanelView 5000 and PanelView Plus 7 PerformanceTerminals

3. Cut out the center white space and the white edges of the drill template, and leave the

shaded part of the template that includes the drill locations.

4. Center the drill template over the existing cutout in the panel.

Align the edge of the existing panel cutout with the interior edge of the drill template.

5. Use the masking tape to secure the drill template to the panel.

6. Use a center punch to mark the center of the drill locations.

7. Remove the drill template and masking tape.

8. Cover and protect components in the enclosure or within the drilling vicinity.

9. To drill the pilot holes, use the 4.76 mm (3/16 in.) drill bit.

10. To drill the finish holes, use the 6.35 mm (1/4 in.) drill bit.

11. Remove any burrs from the drilled holes.

12. Remove all drill shavings from inside the enclosure and the vicinity.

13. Remove the temporary covers and protection from the enclosure and drilling vicinity.

IMPORTANT Make sure that the drill template is flat against the panel with no wrinkles or creases

that can distort the drill locations.

ATTENTION: Make sure that drill shavings do not enter any components that are

installed in the enclosure or in the vicinity. Drill shavings can damage components.

ATTENTION: Use the shortest possible drill bit that will drill completely through the

panel. Do not drill into any existing components inside the enclosure.

Publication VIEW-DS002B-EN-P - September 2018

Drill Template for PanelView™ 5000 and PanelView Plus 7 Performance Terminals 6.5-in. Keypad with Touch Screen Adapter Kit

Panel

Edge of the Existing

Cutout in the Panel

Edge of the Drill Template

6Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018

Adapter Kit for PanelView 5000 and PanelView Plus 7 PerformanceTerminals

Install the Adapter Plate and Backing Plate

Before you install the adapter and backing plate, measure the thickness of the panel to find the

correct mounting lever lock position for the new terminal installation.

Determine the Mounting Lever Lock Position

Use a marker or grease pencil to mark the

mounting lever lock position of each mounting

slots on the back edge of the new terminal. The

marked lock position helps you line up the

mounting lever when you install the new

terminal in step 4 through step 7 in Mount the

Te r m i n a l on page 9.

To install the adapter plate and backing plate,

follow these steps.

1. Verify that the adapter plate and backing plate are flat and not bent.

2. Verify that the sealing gasket is installed on the adapter plate and is not damaged.

This gasket forms a compression seal. Do not use sealing compounds.

3. From the front of the panel, insert the threaded studs of the adapter plate through the

holes that you drilled in the panel.

4. From the back of the panel, insert the backing plate through the threaded studs of the

adapter plate.

5. Finger tighten one nut onto each of the threaded studs. Be sure to hold the backing plate

securely until at least two nuts are in place.

Mounting Slot

Mounting

Lever Lock

Position

Panel Thickness Range Before

the Adapter Kit is Installed

Typical

Gauge

1 1.50…2.01 mm (0.060…0.079 in.) 16

2 2.03…2.64 mm (0.080…0.104 in.) 14

3 2.67…3.15 mm (0.105…0.124 in.) 12

4 3.17…3.66 mm (0.125…0.144 in.) 10

5 3.68…4.16 mm (0.145…0.164 in.) 8/9

6 4.19…4.80 mm (0.165…0.188 in.) 7

ATTENTION: For the following steps, refer to Installation Sequence on page 7.

IMPORTANT Install the backing plate with the raised spacers facing the panel.

Notch

Alignment Mark

In this example, the marker or grease

pencil identifies mounting lever lock

position 3.

Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018 7

Adapter Kit for PanelView 5000 and PanelView Plus 7 PerformanceTerminals

6. Follow the tightening sequence on page 7for your terminal adapter kit.

Installation Sequence

Torque Sequence for Adapter Plate Mounting Nuts–3.90 N•m (30 lb•in)

ATTENTION: To maintain a NEMA Type 4X rating, torque the nuts to 3.90 N•m

(30 lb•in).

Rockwell Automation is not responsible for water or chemical damage to the terminal,

or other equipment within the panel, due to improper installation.

Adapter Plate

with Threaded

Studs and Gasket

Installed on Front

Side of Panel

Enclosure Panel with

Holes thatYou Drilled

Backing Plate Installed on

Back Side of Panel

Raised Spacers

Facing the Panel

Adapter Plate

Mounting Nuts

3110

24 68

31 75

1011

13 14

481362

171453

All 6.5-in. Terminals–

12 Mounting Nuts

All 10.4-in. Terminals–

14 Mounting Nuts

All 12.1-in. and 15-in. Terminals–

16 Mounting Nuts

8Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018

Adapter Kit for PanelView 5000 and PanelView Plus 7 PerformanceTerminals

Prepare to Mount the Terminal

Mounting levers insert into the slots around the terminal bezel to secure the terminal in the

adapter plate. The number of mounting levers varies by terminal size. Each slot has six notches

with alignment marks that are locking positions for a mounting lever. The thickness of the panel

where the terminal is mounted determines the locking position that is required to maintain

NEMA, UL Type, and IP seals. See Determine the Mounting Lever Lock Position on page 6.

Mounting Lever Orientation and Lock Sequence

IMPORTANT The mounting lever orientations that are shown are required to maintain NEMA, UL Type, and

IP seals. If you require a NEMA, UL Type, or IP seal, do not use a mounting lever in another

orientation than shown. See Mounting Lever Orientation and Lock Sequence on page 8.

6.5-in. Touch Only–6 Levers

249

15-in. Touch Only–12 Levers

15-in. Keypad andTouch–14 Levers

846

5173

Back Side

of Terminal

3110

10.4-in. Keypad andTouch,

12.1-in. Touch Only–10 Levers

249

Back Side of Terminal

472

6.5-in. Keypad andTouch–8 Levers

Back Side

of Terminal

Back Side of Terminal

10.4-in. Touch Only–8 Levers

Back Side

of Terminal

The arrows show the direction to rotate the

mounting lever for the final locking position.

Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018 9

Adapter Kit for PanelView 5000 and PanelView Plus 7 PerformanceTerminals

Mount the Terminal

Installing the mounting levers is a multi-step process. Step 4installs each lever so that the

terminal is snug in the adapter plate and the gasket is slightly compressed. Step 6moves the

mounting levers into tighter locking positions until you reach the final locking position that you

previously marked with a marker or grease pencil.

To mount the terminal in the adapter plate, follow these steps.

1. Verify that the sealing gasket is present on the terminal and is not damaged.

This gasket forms a compression seal. Do not use sealing compounds.

2. Insert adapter kit mounting levers in the

top corner slots by using the orientation in

Mounting Lever Orientation and Lock

Sequence on page 8.

The example at right shows the top of a

6.5-in. touch screen terminal.

3. Tilt the terminal into the adapter plate and

guide the terminal upward so that the

mounting levers hold the top of the

terminal in the adapter plate.

If it is difficult to insert the terminal into

the adapter plate, press the bezel at the top

of the terminal to compress the gasket so

you can insert the terminal into the adapter

plate.

4. Insert a mounting lever in the bottom of

the terminal to stabilize the terminal in the adapter plate.

IMPORTANT Before you begin to mount the terminal, read this section and understand the process.

IMPORTANT Use only the adapter kit mounting levers. Do not use any other mounting levers.

Use the Adapter Kit Mounting Levers Do Not Use the Oval Mounting Levers

10 Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018

Adapter Kit for PanelView 5000 and PanelView Plus 7 PerformanceTerminals

5. Insert the remaining levers in the terminal and rotate each lever until the flat side is in

contact with the backing plate and the gasket is slightly compressed.

If it is difficult to insert a mounting lever, press the bezel at the mounting lever position

to compress the gasket so you can insert the mounting lever.

6. Readjust each mounting lever to its final lock position.

a. Rotate mounting lever one in the sequence away from the backing plate.

b. Slide the mounting lever to the final locking position.

If it is difficult to slide the mounting lever, press on the bezel at the mounting lever

position to compress the gasket so you can slide the mounting lever to the final

locking position.

If it is too difficult to slide a mounting lever to its final locking position, then slide

the mounting lever one position at a time until you are able to slide the mounting

levers to the final locking position.

c. Rotate the mounting lever until the flat side is in contact with the backing plate.

d. Lock the remaining mounting levers to their final position.

IMPORTANT Install the mounting levers by the orientation sequence shown inMounting Lever

Orientation and Lock Sequence on page 8.

IMPORTANT Do not install the mounting levers in the final lock position yet. For example, if the

final lock position is 3, slide the lever to notch 4 or 5 (see Determine the Mounting

Lever Lock Position on page 6).

TIP If the mounting levers are over torqued, the pin canbreak off. If a pin is broken, you

can turn the mounting lever over and use the lever in another location that meets

the orientation for the mounting lever.

1234

Flat Side in Contact

With the Backing Plate

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Allen-Bradley Adaptateur

Allen-Bradley

Allen-Bradley PowerFlex 20-COMM-P Manuel utilisateur

Allen-Bradley

Allen-Bradley FLEX I/O PROFIBUS 1794-APBDPV1 Manuel utilisateur

Allen-Bradley

Allen-Bradley 2100-ENET Manuel utilisateur

Allen-Bradley

Allen-Bradley 140G-G-DRA Manuel utilisateur

Allen-Bradley

Allen-Bradley 1738 ArmorPOINT Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 22-COMM-B Manuel utilisateur

Allen-Bradley

Allen-Bradley 140G Series Manuel utilisateur

Allen-Bradley

Allen-Bradley POINT I/O 1734-ADN Manuel utilisateur

Allen-Bradley

Allen-Bradley POINT I/O ControlNet 1734-ACNR Manuel utilisateur

Allen-Bradley

Allen-Bradley Flex I/O Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 20-COMM-D Manuel utilisateur

Allen-Bradley

Allen-Bradley FLEX 5000 Manuel utilisateur

Allen-Bradley

Allen-Bradley 140G Series Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 20-comm-c FRN 1. Series Manuel utilisateur

Allen-Bradley

Allen-Bradley 140G Series Manuel utilisateur

Allen-Bradley

Allen-Bradley Rockwell Automation 1734-AENT Manuel utilisateur

Allen-Bradley

Allen-Bradley ArmorPoint DeviceNet 1738-ADN12 Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 20-COMM-P Manuel utilisateur

Allen-Bradley

Allen-Bradley ArmorPoint DeviceNet A Series Manuel utilisateur

Allen-Bradley

Allen-Bradley Compact I/O 5069 series Manuel utilisateur

Allen-Bradley

Allen-Bradley D Series Manuel utilisateur

Allen-Bradley

Allen-Bradley 1734-AENTRK Manuel utilisateur

Allen-Bradley

Allen-Bradley 1202-CBL-KIT-100M Manuel utilisateur

Allen-Bradley

Allen-Bradley POINT I/O ControlNet 1734-ACNR Manuel utilisateur

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur