Airwolf 3D AW3D HDL Manuel utilisateur
2 | P a g e
AW3D HDL
User Manual
www.Airwolf3D.com
Table of Contents
Specifications .............................................................................................................................................. 4
Unboxing the Printer................................................................................................................................... 5
Box Contents ........................................................................................................................................... 5
Part Directory.............................................................................................................................................. 6
How it Works............................................................................................................................................... 7
Extruder Assembly .................................................................................................................................. 7
Hot End and Heat Bed Motion ................................................................................................................ 7
Plug In & Turn On........................................................................................................................................ 8
Pre-Printing Steps ....................................................................................................................................... 9
Quick Start Guide .................................................................................................................................... 9
Quick Start Guide (contd.)..................................................................................................................... 10
1) Leveling the Bed................................................................................................................................ 11
First Print & Calibration......................................................................................................................... 12
First Print & Calibration (contd.) ........................................................................................................... 13
2) Loading Filament............................................................................................................................... 14
3) Bed Preparation ................................................................................................................................ 15
4) The First Layer ................................................................................................................................... 15
RAMBo Driver ........................................................................................................................................... 16
Setup (Windows 8 Only)........................................................................................................................ 16
Installation (PC Only)............................................................................................................................. 17
5 Steps to Printing..................................................................................................................................... 20
1) Download or Design a 3D Model ...................................................................................................... 21
2) Convert to STL File Type.................................................................................................................... 22
3) Netfabb: Layout (STL Clean Up) ........................................................................................................ 22
3) Netfabb: How To (STL Clean Up)....................................................................................................... 23
4) Slicing ................................................................................................................................................ 24
Slicing: Breakdown ................................................................................................................................ 25
4-5) MatterControl PRO: How To.......................................................................................................... 26
3 | P a g e
4-5) MatterControl PRO: How To (contd.) ............................................................................................ 27
Two Part Epoxy...................................................................................................................................... 28
Firmware...................................................................................................... Error! Bookmark not defined.
Maintenance............................................................................................................................................. 29
Belt Tensioning...................................................................................................................................... 30
Rod Alignment (X-axis).......................................................................................................................... 31
Rod Alignment (Y-axis) .......................................................................................................................... 32
Rod Lubrication ..................................................................................................................................... 33
Inserting Filament ................................................................................................................................. 33
Wiring Diagram ..................................................................................................................................... 34
Clogged Nozzle ...................................................................................................................................... 35
Changing the Nozzle.............................................................................................................................. 36
Trouble Shooting....................................................................................................................................... 37
Glossary of Terms ..................................................................................................................................... 38
Hardware............................................................................................................................................... 38
Software ................................................................................................................................................ 38
Contact List ............................................................................................................................................... 38
Notes......................................................................................................................................................... 39
Notes......................................................................................................................................................... 40
4 | P a g e
Specifications
Copyright 2013 ©
Designed and
Manufactured In:
12 x 8 x 11 inch
300 x 200 x 280 mm
24 x 17.5 x 18 inch
610 x 445 x 460 mm
38 lbs
17 kg
Material that can
be printed:
Filament
Diameter
Nominal: 3.00mm
Actual: 2.85 ± 0.1mm
mm
Nozzle Diameter 0.5 and 0.35 mm
0.1 mm
0.0039 inch
100 mm/s
3.94 inch/s
200 mm/s
7.87 inch/s
Circuit Board
Frame
Power Supply
File Format
System
Compatibility
General
Partially Enclosed Acrylic
Har
d
Printer Size
(LxWxH)
Internal auto-switching 13.5V DC, 300W
Weight
USA
PLA, Soft PLA, PLA 4043D, BendLay,
LayWOO D-3, Laybrick, HIPS, T-Glase,
PVA, TPE & more to come!
Build Volume
(LxWxH)
Minimal Layer
Thickness
Max Speed-
Perimeter
Max Speed-
Travel
Specs.
Matter Control
Cura & Slic3r
RAMBo
Comp.
Software
Netfabb & MeshLab
Windows, Mac, Linux
STL & GCODE
5 | P a g e
Unboxing the Printer
Box Contents
6 | P a g e
Part Directory
7 | P a g e
How it Works
Extruder Assembly
Hot End and Bed Motion
8 | P a g e
Plug In & Turn On
9 | P a g e
Pre-Printing Steps
Quick Start Guide
10 | P a g e
Quick Start Guide (contd.)
Table des matières
Autres manuels Airwolf 3D Imprimante 3D
