Agilent Technologies Infiniium DCA Manuel

Agilent Technologies

Infiniium DCA and DCA-J

Agilent 86100A/B/C

Wide-Bandwidth

Oscilloscope

Programmer’s Guide

Notices

No part of this manual may be reproduced in any

form or by any means (including electronic stor-

age and retrieval or translation into a foreign lan-

guage) without prior agreement and written

consent from Agilent Technologies, Inc. as gov-

erned by United States and international copy-

right lays.

Manual Part Number

86100-90092

Edition

March 2007

Printed in Malaysia

Agilent Technologies, Inc.

Digital Signal Analysis Division

1400 Fountaingrove Parkway

Santa Rosa, CA 95403, USA

Warranty

The material contained in this document is pro-

vided “as is,” and is subject to being changed,

without notice, in future editions. Further, to the

maximum extent permitted by applicable law,

Agilent disclaims all warranties, either express or

implied, with regard to this manual and any infor-

mation contained herein, including but not limited

to the implied warranties of merchantability and

fitness for a particular purpose. Agilent shall not

be liable for errors or for incidental or consequen-

tial damages in connection with the furnishing,

use, or performance of this document or of any

information contained herein. Should Agilent and

the user have a separate written agreement with

warranty terms covering the material in this docu-

ment that conflict with these terms, the warranty

terms in the separate agreement shall control.

Technology Licenses

The hardware and/or software described in this

document are furnished under a license and may

be used or copied only in accordance with the

terms of such license.

LZW compression/decompression: Licensed

under U.S. Patent No. 4,558,302 and foreign

counterparts. The purchase or use of LZW graph-

ics capability in a licensed product does not

authorize or permit an end user to use any other

product or perform any other method or activity

involving use of LZW unless the end user is sepa-

rately licensed in writing by Unisys.

Restricted Rights Legend

If software is for use in the performance of a U.S.

Government prime contract or subcontract, Soft-

ware is delivered and licensed as “Commercial

computer software” as defined in DFAR 252.227-

7014 (June 1995), or as a “commercial item” as

defined in FAR 2.101(a) or as “Restricted com-

puter software” as defined in FAR 52.227-19

(June 1987) or any equivalent agency regulation

or contract clause. Use, duplication or disclosure

of Software is subject to Agilent Technologies’

standard commercial license terms, and non-DOD

Departments and Agencies of the U.S. Govern-

ment will receive no greater than Restricted

Rights as defined in FAR 52.227-19(c)(1-2) (June

1987). U.S. Government users will receive no

greater than Limited Rights as defined in FAR

52.227-14 (June 1987) or DFAR 252.227-7015

(b)(2) (November 1995), as applicable in any tech-

nical data.

Safety Notices

CAUTION

Caution denotes a hazard. It calls attention to a

procedure which, if not correctly performed or

adhered to, could result in damage to or destruc-

tion of the product. Do not proceed beyond a cau-

tion sign until the indicated conditions are fully

understood and met.

WARNING

Warning denotes a hazard. It calls attention to

a procedure which, if not correctly performed or

adhered to, could result in injury or loss of life. Do

not proceed beyond a warning sign until the indi-

cated conditions are fully understood and met.

Trademark Acknowledgements

Microsoft is a U.S. registered trademark of

Microsoft Corporation.

Windows and MS Windows are U.S. registered

trademarks of Microsoft Corporation.

MATLAB ® is a U.S. registered trademark of The

Math Works, Inc.

Contents

Contents-1

1Introduction

Introduction 1-2

Starting a Program 1-4

Multiple Databases 1-6

Files 1-8

Status Reporting 1-11

Command Syntax 1-23

Interface Functions 1-34

Language Compatibility 1-36

New and Revised Commands 1-42

Commands Unavailable in Jitter Mode 1-43

Error Messages 1-45

2Sample Programs

C Programming Examples 2-2

BASIC Programming Examples 2-28

3Common Commands

4Root Level Commands

5System Commands

6Acquire Commands

7Calibration Commands

8Channel Commands

9Clock Recovery Commands

10 Disk Commands

11 Display Commands

12 Function Commands

Contents-2

ContentsContents

13 Hardcopy Commands

14 Histogram Commands

15 Limit Test Commands

16 Marker Commands

17 Mask Test Commands

18 Measure Commands

19 S-Parameter Commands

20 Signal Processing Commands

21 TDR/TDT Commands

(Rev. A.05.00 and Below)

22 TDR/TDT Commands

(Rev. A.06.00 and Above)

23 Timebase Commands

24 Trigger Commands

25 Waveform Commands

26 Waveform Memory Commands

Introduction 1-2

Starting a Program 1-4

Multiple Databases 1-6

Files 1-8

Status Reporting 1-11

Command Syntax 1-23

Interface Functions 1-34

Language Compatibility 1-36

New and Revised Commands 1-42

Commands Unavailable in Jitter Mode 1-43

Error Messages 1-45

Introduction

1-2

Introduction

This chapter explains how to program the instrument. The programming syntax conforms to

the IEEE 488.2 Standard Digital Interface for Programmable Instrumentation and to the

Standard Commands for Programmable Instruments (SCPI). This edition of the manual doc-

uments all 86100-series software revisions up through A.07.00. For a listing of commands

that are new or revised, refer to “New and Revised Commands” on page 1-42.

If you are unfamiliar with programming instruments using the SCPI standard, refer to “Com-

mand Syntax” on page 1-23. For more detailed information regarding the GPIB, the IEEE

488.2 standard, or the SCPI standard, refer to the following books:

• International Institute of Electrical and Electronics Engineers. IEEE Standard 488.1-1987,

IEEE Standard Digital Interface for Programmable Instrumentation. New York, NY, 1987.

• International Institute of Electrical and Electronics Engineers. IEEE Standard 488.2-1987,

IEEE Standard Codes, Formats, Protocols and Common commands For Use with ANSI/

IEEE Std 488.1-1987. New York, NY, 1987.

Throughout this book, BASIC and ANSI C are used in the examples of individual commands.

If you are using other languages, you will need to find the equivalents of BASIC commands

like OUTPUT, ENTER, and CLEAR, to convert the examples.

The instrument’s GPIB address is configured at the factory to a value of 7. You must set the

output and input functions of your programming language to send the commands to this

address. You can change the GPIB address from the instrument’s front panel.

Data Flow The data flow gives you an idea of where the measurements are made on the acquired data

and when the post-signal processing is applied to the data. The following figure is a block dia-

gram of the instrument. The diagram is laid out serially for a visual perception of how the

data is affected by the instrument.

1-3

Introduction

Figure 1-1. Sample Data Processing

The sample data is stored in the channel memory for further processing before being dis-

played. The time it takes for the sample data to be displayed depends on the number of post

processes you have selected. Averaging your sampled data helps remove any unwanted noise

from your waveform.

You can store your sample data in the instrument’s waveform memories for use as one of the

sources in Math functions, or to visually compare against a waveform that is captured at a

future time. The Math functions allow you to apply mathematical operations on your sampled

data. You can use these functions to duplicate many of the mathematical operations that your

circuit may be performing to verify that your circuit is operating correctly. The measure-

ments section performs any of the automated measurements that are available in the instru-

ment. The measurements that you have selected appear at the bottom of the display. The

Connect Dots section draws a straight line between sample data points, giving an analog look

to the waveform. This is sometimes called linear interpolation.

1-4

Introduction

Starting a Program

The commands and syntax for initializing the instrument are listed in Chapter 3, “Common

Commands”. Refer to your GPIB manual and programming language reference manual for

information on initializing the interface. To make sure the bus and all appropriate interfaces

are in a known state, begin every program with an initialization statement. For example,

BASIC provides a CLEAR command which clears the interface buffer. When you are using

GPIB, CLEAR also resets the instrument's parser. After clearing the interface, initialize the

instrument to a preset state using the *RST command.

The AUTOSCALE command is very useful on unknown waveforms. It automatically sets up

the vertical channel, time base, and trigger level of the instrument.

A typical instrument setup configures the vertical range and offset voltage, the horizontal

range, delay time, delay reference, trigger mode, trigger level, and slope. An example of the

commands sent to the instrument are:

:CHANNEL1:RANGE 16;OFFSET 1.00<terminator>

:SYSTEM:HEADER OFF<terminator>

:TIMEBASE:RANGE 1E-3;DELAY 100E-6<terminator>

This example sets the time base at 1 ms full-scale (100 μs/div), with delay of 100 μs. Vertical

is set to 16 V full-scale (2 V/div), with center of screen at 1 V, and probe attenuation of 10.

The following program demonstrates the basic command structure used to program the

instrument.

10 CLEAR 707 ! Initialize instrument interface

20 OUTPUT 707;"*RST" !Initialize instrument to preset state

30 OUTPUT 707;":TIMEBASE:RANGE 5E-4"! Time base to 500 us full scale

40 OUTPUT 707;":TIMEBASE:DELAY 25E-9"! Delay to 25 ns

50 OUTPUT 707;":TIMEBASE:REFERENCE CENTER"! Display reference at center

60 OUTPUT 707;":CHANNEL1:RANGE .16"! Vertical range to 160 mV full scale

70 OUTPUT 707;":CHANNEL1:OFFSET -.04"! Offset to -40 mV

80 OUTPUT 707;":TRIGGER:LEVEL,-.4"! Trigger level to -0.4

90 OUTPUT 707;":TRIGGER:SLOPE POSITIVE"! Trigger on positive slope

100 OUTPUT 707;":SYSTEM:HEADER OFF"<terminator>

110 OUTPUT 707;":DISPLAY:GRATICULE FRAME"! Grid off

120 END

• Line 10 initializes the instrument interface to a known state and Line 20 initializes the

instrument to a preset state.

• Lines 30 through 50 set the time base, the horizontal time at 500 μs full scale, and 25 ns of

delay referenced at the center of the graticule.

• Lines 60 through 70 set the vertical range to 160 millivolts full scale and the center screen at

1-5

Introduction

Starting a Program

−40 millivolts.

• Lines 80 through 90 configure the instrument to trigger at −0.4 volts with normal triggering.

• Line 100 turns system headers off.

• Line 110 turns the grid off.

The DIGITIZE command is a macro that captures data using the acquisition (ACQUIRE) sub-

system. When the digitize process is complete, the acquisition is stopped. The captured data

can then be measured by the instrument or transferred to the computer for further analysis.

The captured data consists of two parts: the preamble and the waveform data record. After

changing the instrument configuration, the waveform buffers are cleared. Before doing a

measurement, the DIGITIZE command should be sent to ensure new data has been collected.

You can send the DIGITIZE command with no parameters for a higher throughput. Refer to

the DIGITIZE command in Chapter 4, “Root Level Commands” for details. When the DIGI-

TIZE command is sent to an instrument, the specified channel’s waveform is digitized with

the current ACQUIRE parameters. Before sending the :WAVEFORM:DATA? query to get

waveform data, specify the WAVEFORM parameters. The number of data points comprising a

waveform varies according to the number requested in the ACQUIRE subsystem. The

ACQUIRE subsystem determines the number of data points, type of acquisition, and number

of averages used by the DIGITIZE command. This allows you to specify exactly what the dig-

itized information contains. The following program example shows a typical setup:

OUTPUT 707;":SYSTEM:HEADER OFF"<terminator>

OUTPUT 707;":WAVEFORM:SOURCE CHANNEL1"<terminator>

OUTPUT 707;":WAVEFORM:FORMAT BYTE"<terminator>

OUTPUT 707;":ACQUIRE:COUNT 8"<terminator>

OUTPUT 707;":ACQUIRE:POINTS 500"<terminator>

OUTPUT 707;":DIGITIZE CHANNEL1"<terminator>

OUTPUT 707;":WAVEFORM:DATA?"<terminator>

This setup places the instrument to acquire eight averages. This means that when the DIGI-

TIZE command is received, the command will execute until the waveform has been averaged

at least eight times. After receiving the :WAVEFORM:DATA? query, the instrument will start

passing the waveform information when queried. Digitized waveforms are passed from the

instrument to the computer by sending a numerical representation of each digitized point.

The format of the numerical representation is controlled with the :WAVEFORM:FORMAT

command and may be selected as BYTE, WORD, or ASCII. The easiest method of entering a

digitized waveform depends on data structures, available formatting, and I/O capabilities. You

must scale the integers to determine the voltage value of each point. These integers are

passed starting with the leftmost point on the instrument's display. For more information,

refer to Chapter 25, “Waveform Commands”. When using GPIB, a digitize operation may be

aborted by sending a Device Clear over the bus (for example, CLEAR 707).

NOTE The execution of the DIGITIZE command is subordinate to the status of ongoing limit tests. (See commands

ACQuire:RUNTil on page 6-4, MTEST:RUNTil on page 17-7, and LTEST:RUNTil on page 15-4.) The DIGITIZE

command will not capture data if the stop condition for a limit test has been met.

1-6

Introduction

Multiple Databases

Eye/Mask measurements are based on statistical data that is acquired and stored in the color

grade/gray scale database. The color grade/gray scale database consists of all data samples

displayed on the display graticule. The measurement algorithms are dependent upon histo-

grams derived from the database. This database is internal to the instrument’s applications.

The color grade/gray scale database cannot be imported into an external database applica-

tion.

If you want to perform an eye measurement, it is necessary that you first produce an eye dia-

gram by triggering the instrument with a synchronous clock signal. Measurements made on a

pulse waveform while in Eye/Mask mode will fail.

Firmware revision A.03.00 and later allows for multiple color grade/gray scale databases to be

acquired and displayed simultaneously, including

• all four instrument channels

• all four math functions

• one saved color grade/gray scale file

The ability to use multiple databases allows for the comparison of

• channels to each other

• channels to a saved color grade/gray scale file

• functions to the channel data on which it is based

The advantage of acquiring and displaying channels and functions simultaneously is test

times are greatly reduced. For example, the time taken to acquire two channels in parallel is

approximately the same time taken to acquire a single channel.

Using Multiple

Databases in

Remote Programs

Most commands that control histograms, mask tests, or color grade data have additional

optional parameters that were not available in firmware revisions prior to A.03.00. You can

use the commands to control a single channel or add the argument APPend to enable more

than one channel. The following example illustrates two uses of the CHANnel<n>:DISPlay

command.

SYSTem:MODE EYE

CHANnel1:DISPlay ON

CHANnel2:DISPlay ON

The result using the above set of commands, is Channel 1 cleared and disabled while Channel

2 is enabled and displayed. However, by adding the argument APPend to the last command of

the set, both Channels 1 and 2 will be enabled and displayed .

SYSTem:MODE EYE

CHANnel1:DISPlay ON

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Agilent Technologies Équipement de test

Agilent Technologies

Agilent Technologies aurora Duet Manuel utilisateur

Agilent Technologies

Agilent Technologies InfiniiVision 7000B Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 16533A 1-GSa/s Manuel

Agilent Technologies

Agilent Technologies N4010A Instructions d'installation et d'utilisation

Agilent Technologies

Agilent Technologies 16048A Manuel d'utilisation

Agilent Technologies

Agilent Technologies 54621A Manuel utilisateur

Agilent Technologies

Agilent Technologies InfiniiVision 6000 Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 93000 SOC Series Guide d'installation

Agilent Technologies

Agilent Technologies InfiniiVision MSO6104A Guide de démarrage rapide

Agilent Technologies

Agilent Technologies Option H48 Multiport Test Set Z5623A Manuel

Agilent Technologies

Agilent Technologies N4419B Manuel utilisateur

Agilent Technologies

Agilent Technologies HP 10070A Manuel utilisateur

Agilent Technologies

Agilent Technologies N5341A Manuel utilisateur

Agilent Technologies

Agilent Technologies MSO8104A Guide de démarrage rapide

Agilent Technologies

Agilent Technologies E7474A Manuel utilisateur

Agilent Technologies

Agilent Technologies 3070 Series Mode d'emploi

Agilent Technologies

Agilent Technologies N4413A Manuel utilisateur

Agilent Technologies

Agilent Technologies 16451B Manuel utilisateur

Agilent Technologies

Agilent Technologies 87075C Option H08 Manuel

Agilent Technologies

Agilent Technologies Agilent 34980A Manuel utilisateur

Agilent Technologies

Agilent Technologies U1602A Manuel

Agilent Technologies

Agilent Technologies InfiniiVision 6000 Series Manuel utilisateur

Agilent Technologies

Agilent Technologies E2969A Manuel utilisateur

Agilent Technologies

Agilent Technologies 54620 Series Instructions d'utilisation et de sécurité

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuel utilisateur

Ritmix

Ritmix RAT-701 Manuel utilisateur