Agilent Technologies PSA Series Guide de démarrage rapide

Installation Note

Part Number E4440-90320

Printed in USA May 2006

Agilent PSA Series Spectrum Analyzers

USB Retrofit Kit, Option 111

Notice.

The information contained in this document is subject to change without notice.

Agilent Technologies makes no warranty of any kind with regard to this material, including

but not limited to, the implied warranties of merchantability and fitness for a particular

purpose. Agilent Technologies shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the furnishing, performance, or use

of this material.

Installation Note E4440-90320 3

USB Retrofit Kit Option 111

Introduction

This retrofit kit adds USB device side I/O to the PSA series spectrum analyzer. USB

device side I/O provides a link for controlling the PSA and extracting data from it

through a standard SCPI interface. This feature does not enable control of USB mass

storage devices. This implementation of USB can be thought of as a faster version of

GPIB.

Once the hardware is installed, it is mandatory to update the PSA firmware so the PSA

can recognize the new hardware.

Products Affected: PSA E4440A

PSA E4443A

PSA E4445A

PSA E4446A

PSA E4447A

PSA E4448A

Serial Numbers: US4430 / US9999

MY4430 / MY9999

SG4430 / SG9999

To Be Performed By: (X) Agilent Service Center

(X) Personnel Qualified by Agilent

( ) Customer

Estimated Hardware Installation Time:

Estimated Adjustment and Verification Time:

Additional Recommended Task:

30 minutes

2 Hours (see Note 1)

Agilent recommends that a full calibration be

performed to verify instrument specifications

(see Note 2)

4Installation Note E4440-90320

USB Retrofit Kit Option 111

NOTE

1. The installation of this kit requires that some performance testing be performed in

order to assure the new option is functioning properly.

This installation note includes a list of required Performance tests. Completing the

performance tests does not guarantee the instrument meets all specifications.

2. The instrument end user must determine whether they need a full instrument

calibration following the installation of the kit. If a full calibration is required,

arrangements regarding the level of calibration must be made between the end user

and the calibration provider.

3. This option is licensed for one instrument model/serial number combination. The

license key will only install on the designated instrument.

Contents

Quantity Description Agilent Part

Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5141

1 PSA User's and Programmers Guide --

1 512 MB Memory Assembly E4440-60252

1 Digital IF Assembly E4440-60206

1 USB cable 8121-1074

1 Cover Plate, rear panel E4440-00061

9 Screw, M3 X 0.5 8 mm LG TORX 0515-0372

Installation Note E4440-90320 5

USB Retrofit Kit Option 111

Tools Required

❏T-20 Torx driv er

❏T-10 Torx driv er

❏PSA Series Spectrum Analyzer Service Guide. This manual is available as part of the

E444xAU Option OBW kits.

❏Calibration software. Latest software information and downloads available at

http://www.agilent.com/find/calibrationsoftware

❏Microsoft Windows based personnel computer with LAN card and CD-ROM drive.

❏Windows 2000 or Windows XP

❏Crossover cable if PC or analyzer is not connected to network. Use a CAT, RJ45 cable

with cross pinning, Agilent p/n 8121-0545.

❏Firmware A.0 9.00 or later. Download the latest revision from

http://www.agilent.com/find/psa_firmware, or order the Firmware Update kit.

Depending on your model number, the firmware update kit is ordered as: Order

E444xAU (Qty.1) Option UE2 (Qty. 1), where the “x” is the last digit of the model

number. For example: E4440AU option UE2.

6Installation Note E4440-90320

Installation Procedure

Preliminary Hardware Verification

1. Check for the presence of Option 115 or Option 117 by pressing System, Show System,

and look at the option list.

NOTE Option 111, Option 115, and Option 117 share the same PC assembly.

2. If Option 115 or Option 117 is present, press System, Show Hardware. Note the part

number of the USB/Flash Driver.

3. Determine the part number of the USB assembly in the kit.

• If the part numbers match, do not install the USB assembly from the kit.

• If the part numbers do not match, install the USB assembly from the kit as

outlined in this installation note.

4. Check the part number of the Digital IF assembly installed in the instrument. Press

System, Show Hardware. Note the part number of the Digital IF.

5. Determine the part number of the Digital IF assembly in the kit by looking at the

part number silk screened on the board assembly.

• If the part numbers match, you do not need to install the Digital IF assembly from

the kit.

• If the part numbers do not match, install the replacement Digital IF assembly as

outlined in this installation note.

Remove the Outer Case

CAUTION If the instrument is placed on its face during any of the following

procedures, be sure to use a soft surface or soft cloth to avoid damage to

the front panel, keys, or input connector.

1. Disconnect the instrument from ac power.

2. Refer to Figure 1. Remove the two handles on the sides of the instrument as shown.

Use the T-20 driver to loosen the screws that attach each handle (1). Remove the

handles.

3. Remove the four bottom feet (2). Lift up on the tabs on the feet, and slide the feet in

the direction indicated by the arrows.

4. Remove the four screws (3) that hold the rear feet (4) in place.

5. Pull the instrument cover (5) off toward the rear of the instrument.

Installation Note E4440-90320 7

Installation Procedure

Figure 1 Instrument Outer Case Removal

8Installation Note E4440-90320

Installation Procedure

Remove the Top Brace

1. Refer to Figure 2. Use the T-10 driver to remove the top screws (3) (one screw is

under the security label), and the side screws (2) attaching the top brace (1) to the

deck.

2. Remove the top brace from the deck.

Figure 2 Top Brace Removal

Installation Note E4440-90320 9

Installation Procedure

Installing the USB Assembly

1. Locate the A6 (SCSI Interface board). When facing the rear panel of the instrument,

the A6 board is in the right side of the instrument.

2. Remove the 6 screws from the rear plate of the A6 SCSI interface board. The plate

will stay attached to the board. See the picture below.

10 Installation Note E4440-90320

Installation Procedure

3. Remove the A6 SCSI interface board. To do this, gently lift the board vertically from

its socket on the PSA motherboard. Once the A6 SCSI interface board is unseated

from the motherboard, it can be removed through the rear panel.

Autres manuels pour PSA Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Agilent Technologies Instrument de mesure

Agilent Technologies

Agilent Technologies E4402BU Manuel utilisateur

Agilent Technologies

Agilent Technologies 1670G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies PSA Series Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 86120C Manuel utilisateur

Agilent Technologies

Agilent Technologies 55B AA Manuel utilisateur

Agilent Technologies

Agilent Technologies E4417A Manuel utilisateur

Agilent Technologies

Agilent Technologies 4286A Manuel utilisateur

Agilent Technologies

Agilent Technologies U1731A Manuel utilisateur

Agilent Technologies

Agilent Technologies 4284A Manuel utilisateur

Agilent Technologies

Agilent Technologies 4294A Manuel utilisateur

Agilent Technologies

Agilent Technologies E4443A Guide de démarrage rapide

Agilent Technologies

Agilent Technologies ESA-L1500A Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies NFA Series Manuel d'utilisation et d'entretien

Agilent Technologies

Agilent Technologies N9010A Manuel utilisateur

Agilent Technologies

Agilent Technologies 86038B Manuel utilisateur

Agilent Technologies

Agilent Technologies 86121A Manuel utilisateur

Agilent Technologies

Agilent Technologies All Manuel

Agilent Technologies

Agilent Technologies 16718A Guide de référence

Agilent Technologies

Agilent Technologies E4991A Manuel utilisateur

Agilent Technologies

Agilent Technologies E4991A Manuel utilisateur

Agilent Technologies

Agilent Technologies U2722A Manuel utilisateur

Agilent Technologies

Agilent Technologies E8361C Guide de démarrage rapide

Agilent Technologies

Agilent Technologies E4991A Manuel utilisateur

Agilent Technologies

Agilent Technologies ACQIRIS DC122 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur