Agilent Technologies 4349B Manuel utilisateur

Safety Summary

When you notice any of the unusual conditions listed below, immediately

terminate operation and disconnect the power cable.

Contact your local Agilent Technologies sales representative or

authorized service company for repair of the instrument. If you continue

to operate without repairing the instrument, there is a potential fire or

shock hazard for the operator.

nInstrument operates abnormally.

nInstrument emits abnormal noise, smell, smoke or a spark-like light

during the operation.

nInstrument generates high temperature or electrical shock during

operation.

nPower cable, plug, or receptacle on instrument is damaged.

nForeign substance or liquid has fallen into the instrument.

WARNING

The 4349B 4-Channel High Resistance Meter and the 16117E Test Lead provided

by Agilent Technologies conform the safety requirements of IEC and CSA, when

the 4349B and the 16117E are operated following the description in this

Operation Manual

Secure the safety of the measurement system, which you have set up. To secure

the safety and to prevent an electrical shock, observe the following safety

precautions when the external voltage source outputs a dangerous voltage, more

than ± 60Vdc and ± 2 mAdc, defined by the safety requirements of IEC and CSA

nAgilent Technologies recommends you to attach the safety interlock function

to the measurement system so that the operator can not touch the parts

where dangerous voltage may appear. If not possible, warn the operators and

the workers around the measurement system not to touch the parts.

nUse the parts with the safety function to prevent an electrical shock caused

by the insulation breakdown, even if dangerous voltage does not appear on

the parts directly.

nTurn OFF the output of the external voltage source and discharge the

remanent charge of the DUT thoroughly, before touching the measurement

system or the DUT where the dangerous voltage may appear.

nUse the power cord shipped with the 4349B and provide an uninterruptible

safety earth ground to the instrument.

nDo

not

apply a dc voltage exceeding ± 50V or ± 50 mA to the INPUT

terminals.

4349B

Conrm the ac line frequency setting of the 4349B.

1. Press .

2. Press un

til

Line

blinks, then press .

Ablinking item means that it is curren

tly selected.

3. If the setting is not matc

hed to the ac line frequency

,press to toggle the setting

bet

een

50 Hz

and

60 Hz

4. Press t

otimes to exit this men

The po

er line frequency setting is stored and is not c

hanged after reset or po

er-o. Once

ou set it, you do not need to set the line frequency as long as the same po

er line frequency

is being used.

Agilent 4349B 4-Channel High Resistance Meter

Operation Manual

SERIAL NUMBERS

This manual applies directly to instruments with serial

number prex JP1KD

,or rmware revision 1.04 or greater

or additional important information about serial

numbers

,read \Serial Number" in Appendix A.

Agilent Part No. 04349-90050

Printed in Japan March 2003

Seventh Edition

Notice

The information contained in this document is subject to change without notice

This document contains proprietary information that is protected by copyright. All rights are

reserved. No part of this document may be photocopied, reproduced, or translated to another

language without the prior written consent of the Agilent T

echnologies.

Agilent T

echnologies Japan, Ltd.

Component T

est PGU-Kobe

1-3-2, Murotani, Nishi-ku, Kobe-shi,

Hyogo

,651-2241 Japan



1996, 1998, 2000, 2001, 2003 Agilent Technologies Japan, Ltd.

Autres manuels pour 4349B

Table des matières

Autres manuels Agilent Technologies Instrument de mesure

Agilent Technologies

Agilent Technologies E5071C Manuel utilisateur

Agilent Technologies

Agilent Technologies PNA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 1145A Manuel

Agilent Technologies

Agilent Technologies OmniBER OTN Series Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies ESA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies J2126A Manuel utilisateur

Agilent Technologies

Agilent Technologies G7035A Manuel utilisateur

Agilent Technologies

Agilent Technologies 700 Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 2100 Bioanalyzer System Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 4156b Manuel utilisateur

Agilent Technologies

Agilent Technologies 86038B Manuel utilisateur

Agilent Technologies

Agilent Technologies G6691A Manuel utilisateur

Agilent Technologies

Agilent Technologies 8510XF Manuel de service

Agilent Technologies

Agilent Technologies NFA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies Agilent 4396B Mode d'emploi

Agilent Technologies

Agilent Technologies HP 1660E Series Manuel utilisateur

Agilent Technologies

Agilent Technologies Flow Tracker 1000 Series Manuel d'utilisation

Agilent Technologies

Agilent Technologies 8753ET Manuel utilisateur

Agilent Technologies

Agilent Technologies N5230C Manuel utilisateur

Agilent Technologies

Agilent Technologies 86142B Manuel utilisateur

Agilent Technologies

Agilent Technologies ESA-E E4402B Manuel utilisateur

Agilent Technologies

Agilent Technologies 55B AA Manuel utilisateur

Agilent Technologies

Agilent Technologies E5061B Manuel utilisateur

Agilent Technologies

Agilent Technologies N6705 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur