Agilent Technologies G6600 Mode d’emploi

Purpose

The Brass Burner has two ceramic combustion tubes which require periodic

replacement: an inner and an outer tube.

Scope

This procedure applies to ceramic tube replacement in the Agilent Instruments

ABI 00003 Brass Burner.

Tools

•2 - 1/16” Open End Wrenches

•2 - 3/8” Open End Wrenches

•2 - 7/16” Open End Wrenches

Procedure

1. Turn off the Interface Controller and let the system cool down under

vacuum.

The Burner is extremely hot when running. Do not touch the burner until it has

cooled down.

2. Turn off the vacuum pump.

3. Remove the hydrogen line by disconnecting the Hydrogen Inlet Fitting at

the top of the Burner. Use a second wrench to hold the Adapter Tee to

avoid excess torque on the ceramic tubes.

4. Disconnect the black PFA transfer line from the Tee of the Burner

Interface.

5. Unscrew the Tee fitting and carefully pull the inner Tube/Tee assembly

from the Burner. If the existing Tube is broken then all fragments must

be removed from the burner.

Note

Ceramic Probe Replacement

Instructions

Accessory G6600-60034

6. Remove the ferrule attached to the top of the 1/8” ceramic tube.

7. Disconnect the Heater Cable from the heating element leads.

The heating element leads are very fragile. Do not bend them excessively or they

will be damaged.

8. Disconnect the thermocouple leads from the Interface Controller.

9. Remove the four horizontal socket head cap screws holding the Burner

Case.

10. Carefully lift the Burner Case up off of the base and set it aside.

11. Remove the white insulating disk and the fiber insulating toroid from the

Burner base.

12. Remove the 1/8” ceramic tube by loosening the nut in the Burner base.

Discard the used ceramic tube and ferrule. Remove any debris from the

inside of the connection.

Screw extractors may be useful in removing old ferrules from Burner fittings.

Note

13. Insert the new 1/8” ceramic tube into the fitting with a new Vespel

ferrule. Slide the nut over the tube and tighten it until finger tight. Lift

the ceramic tube up 1 to 2 mm so that it will not be crushed by the

compression fitting. Tighten the nut snugly with the 7/16” wrench. This

connection must be fairly tight to ensure that the nut does not loosen

under heat stress, but excessive tightening can crack the ceramic tube.

14. Reinstall the fiber insulating toroid and the white insulating disk.

Carefully slide the Burner Cover over the large ceramic tube. It is often

useful to sight down the upper fitting to ensure that the ceramic tube is

properly aligned and will not break.

Failure to install the insulating disk may lead to leaks in the Burner.

15. Reinstall the four screws at the base of the Burner.

16. Unscrew the Hydrogen Inlet fitting from the Tee, and remove the 1/16"

tube and ferrule.

Note

17. Install a new 1/16" Vespel ferrule at the top of the Tee. Slide in a new

inner ceramic tube until approximately 1/8" (2 mm) extends out of the

top of the ferrule Retighten the Hydrogen Inlet fitting snugly. Do not

overtighten the fitting.

18. Replace the Tube and Tee assembly into the Burner, tightening finger

tight.

19. Check the flow of air and hydrogen following the Detector manual

instructions.

20. Reconnect the Heater Cable, Thermocouple, and all the tubing. Pressure

test the system following the instructions in the Detector manual. The

pressure may change slightly due to variation in tube dimensions.

21. Turn on the Interface Controller and allow the Burner temperature to

stabilize. Gently tighten all the fittings once the Burner temperature is

stable.

Agilent Technologies, Inc.

2850 Centerville Road

Wilmington, DE 19808-1610

Printed in the USA Feb 2007

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Agilent Technologies Instrument de mesure

Agilent Technologies

Agilent Technologies E444 AU Series Manuel utilisateur

Agilent Technologies

Agilent Technologies All Manuel

Agilent Technologies

Agilent Technologies 4291B Manuel utilisateur

Agilent Technologies

Agilent Technologies 16089E Guide de démarrage rapide

Agilent Technologies

Agilent Technologies ESA E4401B Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 1145A Manuel

Agilent Technologies

Agilent Technologies HP 5890 II Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 8720E Series Manuel utilisateur

Agilent Technologies

Agilent Technologies Cary 60 Manuel utilisateur

Agilent Technologies

Agilent Technologies 8590L Manuel utilisateur

Agilent Technologies

Agilent Technologies B2901 Manuel utilisateur

Agilent Technologies

Agilent Technologies 5185-5991 Manuel utilisateur

Agilent Technologies

Agilent Technologies u8903a Manuel utilisateur

Agilent Technologies

Agilent Technologies NFA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 1680 series Manuel utilisateur

Agilent Technologies

Agilent Technologies ESA-L1500A Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 8712ET Manuel utilisateur

Agilent Technologies

Agilent Technologies HP 8719D Manuel utilisateur

Agilent Technologies

Agilent Technologies 4294A Manuel du propriétaire

Agilent Technologies

Agilent Technologies 35670A Manuel utilisateur

Agilent Technologies

Agilent Technologies N4962A Manuel utilisateur

Agilent Technologies

Agilent Technologies 8510XF Manuel de service

Agilent Technologies

Agilent Technologies Seahorse XFe96 Manuel utilisateur

Agilent Technologies

Agilent Technologies 35670A Manuel

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur