Agilent Technologies 16089E Guide de démarrage rapide

Agilent 16089E K

elvin Clip Leads

Operation Note

Agilent Part No. 16089-90001

Printed in JAPAN May 2000

Notice

The information contained in this document is subject to change without notice

This document contains proprietary information that is protected by copyright. All rights are

reserved. No part of this document may be photocopied, reproduced, or translated to another

language without the prior written consent of the Agilent T

echnologies

Agilent T

echnologies Japan, Ltd.

Component T

est PGU-Kobe

1-3-2, Murotani, Nishi-ku, Kobe-shi,

Hyogo

,651-2241 Japan



Safety Summary

The following general safety precautions must be observed during all phases of operation,

service

,and repair of this instrument. F

ailure to comply with these precautions or with specic

ARNINGS

elsewhere in this manual may impair the protection provided by the equipment.

In addition it violates safety standards of design, manufacture, and intended use of the

instrument.

The A

gilent T

echnologies assumes no liability for the customer's failure to comply with these

requirements

DO NOT Operate In An Explosive Atmosphere

Do not operate the instrument in the presence of ammable gasses or fumes

.Operation of any

electrical instrument in such an environment constitutes a denite safety hazard.

eep A

way From Live Circuits

Operating personnel must not remove instrument covers. Component replacement and internal

adjustments must be made by qualied maintenance personnel. Do not replace components

with the power cable connected. Under certain conditions

, dangerous voltages may exist even

with the power cable removed. T

oavoid injuries

,always disconnect power and discharge

circuits before touching them.

DO NOT Service Or A

djust Alone

Do not attempt internal service or adjustment unless another person, capable of rendering rst

aid and resuscitation, is present.

DO NOT Substitute P

arts Or Modify Instrument

Because of the danger of introducing additional hazards

,do not install substitute parts or

perform unauthorized modications to the instrument. Return the instrument to a Agilent

echnologies Sales and Service Oce for service and repair to ensure that safety features are

maintained.

Dangerous Procedure W

arnings

,such as the example below

,precede potentially dangerous procedures throughout

this manual. Instructions contained in the warnings must be followed.

arning

Dangerous voltages

,capable of causing death, are present in this

instrument. Use extreme caution when handling, testing, and adjusting

this instrument.

Safety Symbols

General denitions of safety symbols used on equipment or in manuals are listed below

This

Warning

sign denotes a hazard. It calls attention to a procedure

, practice

condition or the like

, which, if not correctly performed or adhered to

, could

result in injury or death to personnel.

This

Caution

sign denotes a hazard. It calls attention to a procedure

, practice

condition or the like

, which, if not correctly performed or adhered to

, could

result in damage to or destruction of part or all of the product.

Note

denotes important information. It calls attention to a procedure,

practice, condition or the like, which is essential to highlight.

iii

Certication

Agilent T

echnologies certies that this product met its published specications at the time

of shipment from the factory. Agilent T

echnologies further certies that its calibration

measurements are traceable to the United States National Institute of Standards and

echnology

,to the extent allowed by the Institution's calibration facility

,orto the calibration

facilities of other International Standards Organization members.

arranty

This Agilent T

echnologies instrument product is warranted against defects in material and

workmanship for aperiod of one year from the date of shipment, except that in the case of

certain components listed in

General Information

of this manual, the warranty shall be for the

specied period. During the warranty period, Agilent T

echnologies will, at its option, either

repair or replace products that prove to be defective

or warranty service or repair

,this product must be returned to aservice facility designated by

Agilent T

echnologies

.Buyer shall prepay shipping charges to Agilent T

echnologies and Agilent

echnologies shall pay shipping charges to return the product to Buyer

.However

,Buyer shall

pay all shipping charges

,duties

,and taxes for products returned to Agilent T

echnologies from

another country

Agilent T

echnologies warrants that its software and rmware designated by Agilent

echnologies for use with an instrument will execute its programming instruction when

property installed on that instrument. Agilent T

echnologies does not warrant that the operation

of the instrument, or software

,or rmware will be uninterrupted or error free

Limitation Of W

arranty

The foregoing warranty shall not apply to defects resulting from improper or inadequate

maintenance by Buyer

,Buyer-supplied software or interfacing, unauthorized modication or

misuse

, operation outside the environmental specications for the product, or improper site

preparation or maintenance

No other warranty is expressed or implied. A

gilent T

echnologies specically disclaims the

implied warranties of merchantability and tness for aparticular purpose

Exclusive Remedies

The remedies provided herein are buyer's sole and exclusive remedies

.Agilent T

echnologies

shall not be liable for any direct, indirect, special, incidental, or consequential damages

whether based on contract, tort, or any other legal theory

Assistance

Product maintenance agreements and other customer assistance agreements are available for

Agilent Technologies products.

For any assistance, contact your nearest Agilent Technologies Sales and Service Oce.

Addresses are provided at the back of this manual.

General Information

Introduction

The purpose of this manual is to enable you to use your 16089E Kelvin Clip Leads eciently

and condently. This manual contains both general and specic information.

Product Description

The 16089E has been designed to operate specically with the following four-terminal-pair type

LCR meters and impedance analyzers:

4263B

4278A

4284A

4285A

4192A

4194A

The 16089E makes it possible to measure odd-shaped components that cannot be measured

with conventional test xtures

.The 16089E consists of adirect attachment, four-terminal-pair

type test leads that are equipped with two insulated Kelvin clips

ccessories Supplied

The following accessories are supplied with the 16089E:

able 1-1. Furnished A

ccessories

Description P

art Number Quantity

Operation Note P/N 16089-90001 1

General Information 1-1

Operating and Safety Precautions

Operating

ou need observe only normal precautions in handling and operating the 16089E. Do not

exceed the operating input power

,voltage, and current level and signal type appropriate for

the instrument being used, refer to your instrument's operation manual.

Caution

Electrostatic discharge (

esd

)candamage the highly sensitive microcircuits

in your instrument. ESD damage is most likely to occur as the test leads are

being connected or disconnected. Protect them from ESD damage by wearing a

grounding strap that provides ahigh resistance path to ground. Alternatively

ground yourself to discharge any static charge built-up by touching the

outer shell of any grounded instrument chassis before touching the test port

connectors

Never touch the test clip contacts

Use awork station equipped with an anti-static work surface

Service

The voltage levels found in the test leads when used with the intended instruments do not

warrant more than normal safety precautions for operator safety

.Nevertheless

, service should

be performed only by qualied personnel.

1-2 General Information

Specications

These specications are the performance standards and limits against which the 16089E is

tested. When shipped from the factory

,the16089E meets the following specications:

Applicable Instrument

::::::::::

:::::::::::::::::::::::

::::::::::::::::::::::: :

4263B,4278A

,4284A

,4285A

::::::

:::: :::::::::::::::::::

:::::::::::::::::::::::

::::::::::::::::::

4192A

,4194A

Maximum dc Bias V

oltage

:::

::::::::::::::::::::: ::::

::::::::::::::::::::: :

42 V peak max

Frequency Range

::::

:::::::::::::::::::::::

::::::::::::::::::::: :: :::::

5Hz to 100 kHz

Operating T

emperature

:::

:::::::::::::::::::::

::::::::::::::::::::: ::::

:::::

0to 55



Operating Humidity

:::::: ::::

::::::::::::::::::::: :: :: :::::::::::::::::::



95% RH (@40



Non-operating T

emperature

::::: :::::::::::::::::::

:::: :: :::::::::::::::::::

40 to 70



Non-operating Humidity

:::: :: :::::::::::::::::::::

:::::::::::::::::::::::



95% RH (@40



Cable Length

:::: :::::::::::::::::::::

:::::::::::::::::::::::

:::::::::

approximately 1m

Except for the frequency range over 100 kHz.

Supplemental P

erformance Characteristics

Supplemental performance characteristics are not specications

,but are typical characteristics

included as additional information for the operator

.Supplemental performance characteristics

are not guaranteed.

Applicable DUT size

Diameter of DUT's terminals

::::::::::::::::::::::::::::::::::::::::::::::::::::::::



6.0 mm

General Information 1-3

Operation

Introduction

This chapter explains how to use the 16089E Kelvin Clip Leads

Initial Inspection

The 16089E has been carefully inspected electrically and mechanically before being shipped

from the factory

.It should be in perfect physical condition, no scratches

,dents or the like

,and

they should be in perfect electrical condition. V

erify this by carefully performing an incoming

inspection to check the test lead set for signs of physical damage and missing contents

.If any

discrepancy is found, notify the carrier and Agilent Technologies

our Agilent T

echnologies

sales oce will arrange for repair and replacement without waiting for the claim to be settled.

1. Inspect the shipping container for damage

,and keep the shipping materials until the

inspection is completed.

2. V

erify that the shipping container contains everything shown in Figure 2-1 and listed in

able 2-1.

3. Inspect the exterior of the 16089E for any signs of damage

Figure 2-1. 16089E Product Overview

Table 2-1. Contents of 16089E

Description Agilent Part Number Quantity



Kelvin Clip Leads 16089-60005



Operation Note

16089-90001 1

Agilent internal-only part number.

Operation Note is not shown in Figure 2-1.

Operation 2-1

Ambient Environmental Considerations

Operating and Storage

The 16089E must be operated within an ambient temperature range of 0



Cto 55



Cand relative

humidity up to 95% at 40



C(non-condensing).

The 16089E may be stored within a temperature range of



Cto +70



,and at arelative

humidity of up to 95% at +40



C(non-condensing).

ackaging the Test Leads

If shipment to aAgilent T

echnologies service center is required, each test lead set should be

repackaged using the original factory packaging materials

Alteratively

,comparable packaging materials may be used. Wrap the test leads in heavy paper

and pack in anti-static plastic packing material. Use sucient shock absorbing material on

all sides of the 16089E to provide a thick, rm cushion and to prevent movement. Seal the

shipping container securely and mark it

FRA

GILE

2-2 Operation

Table des matières

Autres manuels Agilent Technologies Instrument de mesure

Agilent Technologies

Agilent Technologies ESA-E Series Manuel

Agilent Technologies

Agilent Technologies OmniBER OTN Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 77-4 Instructions d'installation et d'utilisation

Agilent Technologies

Agilent Technologies N9030A Manuel utilisateur

Agilent Technologies

Agilent Technologies U1211A Manuel utilisateur

Agilent Technologies

Agilent Technologies N9020A Manuel utilisateur

Agilent Technologies

Agilent Technologies 4291B Manuel utilisateur

Agilent Technologies

Agilent Technologies ESA-E Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 1156A Manuel utilisateur

Agilent Technologies

Agilent Technologies 8753ET Manuel utilisateur

Agilent Technologies

Agilent Technologies PSA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies EMC Series Manuel utilisateur

Agilent Technologies

Agilent Technologies WireScope 350 Manuel utilisateur

Agilent Technologies

Agilent Technologies ENA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies PSA Series Mode d'emploi

Agilent Technologies

Agilent Technologies 4352B Manuel utilisateur

Agilent Technologies

Agilent Technologies E4411-60019 Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 490 Micro GC Manuel utilisateur

Agilent Technologies

Agilent Technologies PNA Series Mode d'emploi

Agilent Technologies

Agilent Technologies 16800 Series Fiche technique

Agilent Technologies

Agilent Technologies 4338B Manuel utilisateur

Agilent Technologies

Agilent Technologies NFA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 4418B Manuel utilisateur

Agilent Technologies

Agilent Technologies 4284A Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur