Agilent Technologies ICP-MS Series Mode d'emploi

Agilent ICP-MS

Interactive Troubleshooting tool for

Plasma ignition problem

Next >

Rev. B

2017, January, 20

Preconditions

•7900, 7800, 7700, 8800, or 8900 ICP-MS is used.

•Sample introduction type is “PeriPump”. If you are using a special configuration such as

LC/GC integration or ISIS, setup the instrument with standard configuration.

•You have the “Hardware Maintenance Manual”for your instrument. Some details of the

operations are not in this tool. You should refer to the manual.

<Previous Next >

Legends

Notes or tips that help troubleshoot.

You need to refer to another document for detail of the steps.

Good example of situation.

Bad example of situation.

Did the ion lens test pass? ←Questions are displayed in blue you need to click

buttons such as or

Based on your answer the tool will navigate you to next step.

Note

Reference

Good

Bad

<Previous Next >

Yes No

1.1.1 Check Water flow and Gas flow errors

(1) Select MassHunter Instrument Control Window → Main menu → “View” → “Instrument

Status” to display “Instrument Status” Pane

If Main menu is not displayed, press F10 key.

(2) Click the dropdown below and check the error number for errors that are generated at the

date/time of the attempt to ignite plasma.

(3) Are error numbers 1440, 1445, or 1446 included in the latest errors?

Note

<Previous Yes No

1.2.1 Check water and argon gas

(1) If error 1440 has been generated, check if cooling water valve is open and chiller or heat

exchanger is working correctly.

(2) If error 1445 or 1446 have been generated, check if argon gas valve is open and remaining

amount is enough.

(3) Did this solve the problem？

Yes No

1.3.1 Check timing when Plasma goes out

(1) When did Plasma go out?

Not ignite at all

Several seconds after ignition

One to several minutes after ignition

When "Plasma Correction“ is going on

20 minutes or later after ignition

2.1.1 Check condition of argon gas line condition

(1) Are there any situations below?

-Ar cylinder has been replaced recently

-Was there any work on Ar line recently?

-Is the instrument used after a long time ( > 1 month).

Yes No

2.2.1 Check condition of argon gas line

(1) Purge Ar line.

(2) Do leak check on Ar line.

(3) Check specification of Ar gas to have ≧99.99% purity (In case cylinder has been replaced).

(4) Try alternative source of Ar gas (In case cylinder has been replaced and any alternatives

are available)

(5) Does this fix the problem?

Yes No

2.3.1 Isolate the torch and try to ignite

(1) Block end of the torch with plastic film and try to ignite.

(2) Can it ignite?

Yes No

2.4.1 Check torch box

(1) Open the torch box and observe to check if there are situations below, following

instruction from the next page.

- Damaged torch

- Damaged bonnet

- Damaged shield plate

- Damaged shield contact

-Non Agilent torch

-Dirty torch stand

-Wrongly assembled torch

<Previous Next >

Ce manuel convient aux modèles suivants

5

Table des matières

Autres manuels Agilent Technologies Instrument de mesure

Agilent Technologies

Agilent Technologies 490 Manuel utilisateur

Agilent Technologies

Agilent Technologies 100 Manuel utilisateur

Agilent Technologies

Agilent Technologies Varian MERCURY Series Manuel technique

Agilent Technologies

Agilent Technologies ENA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 7820A Manuel utilisateur

Agilent Technologies

Agilent Technologies U1701A Manuel utilisateur

Agilent Technologies

Agilent Technologies Cary 50 Manuel utilisateur

Agilent Technologies

Agilent Technologies OmniBER 720 Manuel utilisateur

Agilent Technologies

Agilent Technologies 8702D Manuel utilisateur

Agilent Technologies

Agilent Technologies VS Series Guide de référence

Agilent Technologies

Agilent Technologies 1670G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies E5072A ENA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies N9030A Manuel utilisateur

Agilent Technologies

Agilent Technologies 10400B Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 4284A Manuel utilisateur

Agilent Technologies

Agilent Technologies 89410A Manuel

Agilent Technologies

Agilent Technologies E5500A Manuel utilisateur

Agilent Technologies

Agilent Technologies N4962A Manuel utilisateur

Agilent Technologies

Agilent Technologies 1156A Manuel utilisateur

Agilent Technologies

Agilent Technologies 34952a Manuel utilisateur

Agilent Technologies

Agilent Technologies 8753ET Manuel utilisateur

Agilent Technologies

Agilent Technologies X Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 35670A Manuel utilisateur

Agilent Technologies

Agilent Technologies E5900B Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur