AEMC OX 5042B Manuel utilisateur

Handscope Harmonic Analyzer

Oscilloscope

Model OX 5042B

ENGLISH

PORTABLE OSCILLOSCOPES

WITH AEMC

INSTRUMENTS

Quick Start Guide

No part of this documentation may be reproduced in any form or by any means (including electronic

storage and retrieval or translation into any other language) without prior agreement and written consent

from Chauvin Arnoux®, Inc., as governed by United States and International copyright laws.

Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments

15 Faraday Drive • Dover, NH 03820 USA

Tel: (800) 945-2362 or (603) 749-6434 • Fax: (603) 742-2346

This documentation is provided “as is,” without warranty of any kind, express, implied, or otherwise.

Chauvin Arnoux®, Inc. has made every reasonable e󰀨ort to ensure that this documentation is accurate;

but does not warrant the accuracy or completeness of the text, graphics, or other information contained

in this documentation. Chauvin Arnoux®, Inc. shall not be liable for any damages, special, indirect,

incidental, or inconsequential; including (but not limited to) physical, emotional or monetary damages

due to lost revenues or lost prots that may result from the use of this documentation, whether or not the

user of the documentation has been advised of the possibility of such damages.

Statement of Compliance

Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments

certies that this instrument has been calibrated

using standards and instruments traceable to

international standards.

We guarantee that at the time of shipping your

instrument has met its published specications.

An NIST traceable certicate may be requested

at the time of purchase, or obtained by returning

the instrument to our repair and calibration

facility, for a nominal charge.

The recommended calibration interval for this

instrument is 12 months and begins on the date of

receipt by the customer. For recalibration, please

use our calibration services. Refer to our repair and

calibration section at www.aemc.com.

Serial #:

Catalog #: 2150.21 / 2150.22 / 2150.23

Model #: OX 5042B

Please ll in the appropriate date as indicated:

Date Received:

Date Calibration Due:

Chauvin Arnoux®, Inc.

d.b.a AEMC®Instruments

www.aemc.com

Handscope Harmonic Analyzer Oscilloscope Model OX 5042B

PRODUCT PACKAGING (2150.21)

Handscope Oscilloscope

Model OX 5042B

Cat. #2150.21

(1) USB Cable + Driver

Cat. #2135.41

(2) Probe 10:1 600 V BNC-M

Cat. #5000.50

(1) US Wall Plug,

Adapter 5 V

Cat. #2153.78

(1) USB Drive

(SX-METRO Software

OX 5042B User Manual

(1) Adapter Banana-F

BNC-M

Cat. #2118.46

(1) Set of two color-coded

leads and clips

Cat. #2140.63

(1) Black Tool Bag

Cat. #2133.72

(1) Red Test Probe

Cat. #5000.98

(1) Black Test Probe

Cat. #5000.97

OX 5022B / OX 5042B

Cable - Replacement USB

Charging Cable

Cat. #5100.17

Also Included:

(1) Test Report

(1) Battery Information Sheet

(6) 1.2 V NiMH rechargeable batteries 2700 mA·h

Handscope Harmonic Analyzer

Oscilloscope Model OX 5042B

PRODUCT PACKAGING (2150.22)

Handscope Oscilloscope

Model OX 5042B

Cat. #2150.21

(1) USB Cable + Driver

Cat. #2135.41

(2) Probe 10:1 600 V BNC-M

Cat. #5000.50

(1) US Wall Plug,

Adapter 5 V

Cat. #2153.78

(1) USB Drive

(SX-METRO Software

OX 5042B User Manual

(1) Adapter Banana-F

BNC-M

Cat. #2118.46

(1) Set of two color-coded

leads and clips

Cat. #2140.63

(1) Carrying Case

Cat. #2155.77

(1) Red Test Probe

Cat. #5000.98

(1) Black Test Probe

Cat. #5000.97

OX 5022B / OX 5042B

Cable - Replacement USB

Charging Cable

Cat. #5100.17

Also Included:

(1) Test Report

(1) Battery Information Sheet

(6) 1.2 V NiMH rechargeable batteries 2700 mA·h

(1) Current Probe

MN251T

Cat. #2132.59

(1) Current Probe

MF3000-24-1-1

Cat. #2132.63

Handscope Harmonic Analyzer Oscilloscope Model OX 5042B

PRODUCT PACKAGING (2150.23)

Handscope Oscilloscope

Model OX 5042B

Cat. #2150.21

(1) USB Cable + Driver

Cat. #2135.41

(2) Probe 10:1 600 V BNC-M

Cat. #5000.50

(1) US Wall Plug,

Adapter 5 V

Cat. #2153.78

(1) USB Drive

(SX-METRO Software

OX 5042B User Manual

(1) Adapter Banana-F

BNC-M

Cat. #2118.46

(1) Set of two color-coded

leads and clips

Cat. #2140.63

(1) Carrying Case

Cat. #2155.77

(1) Red Test Probe

Cat. #5000.98

(1) Black Test Probe

Cat. #5000.97

OX 5022B / OX 5042B

Cable - Replacement USB

Charging Cable

Cat. #5100.17

Also Included:

(1) Test Report

(1) Battery Information Sheet

(6) 1.2 V NiMH rechargeable batteries 2700 mA·h

(1) Current Probe

MN379T

Cat. #2132.60 (1) Current Probe

MF3000-14-1-1

Cat. #2132.60

Handscope Harmonic Analyzer

Oscilloscope Model OX 5042B

Thank you for purchasing an AEMC®Instruments Portable Oscilloscope

Model OX 5042B.

For the best results from your instrument and for your safety, you must

read the enclosed operating instructions carefully and comply with the

precautions for use. Only qualied and trained operators should use this

product.

Symbols and Denitions

Signies that the instrument is protected by double or reinforced insulation

CAUTION - Risk of Danger! Indicates a WARNING. Whenever this symbol

is present, the operator must refer to the user manual before operation

Indicates a risk of electric shock. The voltage at the parts marked with this

symbol may be dangerous

Indicates important information to acknowledge

This product complies with the Low Voltage & Electromagnetic Compatibility

European directives (73/23/CEE & 89/336/CEE)

Ground/Earth

The product has been declared recyclable

In the European Union, this product is subject to a separate collection

system for recycling electrical and electronic components in accordance with

directive WEEE 2002/96/EC

Denition of Measurement Categories (CAT)

CAT IV corresponds to measurements performed at the primary electrical

supply (< 1000 V).

Example: primary overcurrent protection devices, ripple control units, and

meters.

CAT III corresponds to measurements performed in the building installa-

tion at the distribution level.

Example: hardwired equipment in xed installation and circuit breakers.

CAT II corresponds to measurements performed on circuits directly con-

nected to the electrical distribution system.

Example: measurements on household appliances and portable tools.

Handscope Harmonic Analyzer Oscilloscope Model OX 5042B

Precautions For Use

The operator and/or the responsible authority must carefully read and

completely understand the precautions before use. If you use this instrument

in an unspecied manner, the protection it ensures can be compromised, thus

putting you in danger.

This instrument is designed for use:

• indoors

• in a level 2 pollution environment

• at an altitude below 2000 m

• at a temperature between 0 °C and 40 °C

• with a relative humidity of less than 80 % up to 35 °C.

The safety of all systems, including the instrument, is the responsibility of

the operator.

It can be used for measurements on 600 V CAT III circuits, relative to the

ground/earth.

Before each use, check the condition of the insulation on the cables, boxes,

sensors and accessories. Any element on which the insulation is damaged

(even partially) must be taken out of service for repair or disposal.

Respect the environmental and storage conditions.

The external power supply must be connected to the instrument and to the

network (98 to 264 VAC).

The power supply to the instrument is tted with an automatically resettable

electrical protection after disappearance of the fault.

As a safety measure, only use factory supplied parts and accessories.

It is advised to use individual safety protection whenever the environmental

situations in which the instrument is used require it.

When handling the sensors or test probes, do not place your ngers beyond

the physical guard.

If the battery housing cover is absent, damaged or incorrectly positioned,

the instrument must not be used other than to adjust the sensors.

Power Supply

The oscilloscope is supplied with one external power supply and set of 6 x 1.2 V

NiMH rechargeable batteries 2700 mA·h.

When the supplied wall plug is connected from the instrument to an external

power source, battery power is not needed. The batteries are only used when

there is no external power supply available.

Before the rst use, start by fully charging the battery.

NOTE: The batteries automatically begin recharging when the

Oscilloscope is powered o󰀨, but connected to an external power

supply.

Handscope Harmonic Analyzer

Oscilloscope Model OX 5042B

When the batteries are recharging, the Battery Charge LED on the front panel

will turn on steady.

The LED will blink in the following situations:

• pre-charge of very low batteries

• temperature is too low or too high

• batteries are damaged

When the charge is complete, the LED will turn o󰀨.

If the batteries need to be replaced, they must be replaced with NiMH

rechargeable batteries. Battery charge life is guaranteed for same-capacity

batteries (in mA·h) as those shipped with the oscilloscope.

To remove the battery cover, use a coin to turn the slot on the back of the unit

counter-clockwise.

Description

The Handscope Oscilloscope Model OX5042B combines three instruments into

one:

• 40 MHz oscilloscope

• Independent 8000 ct multimeter with power measurements

• Built-in harmonic analyzer out to the 31st harmonic (fundamental between

40 and 450 Hz)

The instrument operates at a constant acquisition depth of 2500 points.

An LCD TFT screen is used to view the applied signals along with all the setting

parameters.

The main command functions are accessible using the buttons on the front

panel.

A graphic interface is used to:

■adjust the parameters related to the selected button

■navigate using a horizontal main menu showing the current settings and

vertical sub-menus

Handscope Harmonic Analyzer Oscilloscope Model OX 5042B

Channel Isolation

The two oscilloscope input channels are isolated from each other and from the

ground/earth and the main power supply block. This isolation is provided by

double or reinforced insulation, in compliance with the safety standards IEC

61010-1 and IEC 61010-2-030.

This makes it possible to make measurements on installations or systems

connected to the electricity supply network for voltages of up to 600 V in CAT

III. The common mode authorized between the two channels is 600 V in CAT

III. Thus the operator, the test systems and the environment are completely

protected at all times.

Any voltage (even dangerous) on one channel will not be present on the other

channel. The low points of the inputs are completely insulated, so there is

no possibility of the low points looping (which can be dangerous and highly

destructive).

NOTE: The use of accessories with a voltage and/or category lower

than 600 V CAT III reduces the operating range to the lower voltages

and/or categories.

The oscilloscope is rated 600 V CAT III; at least 600 V CAT III

accessories must be used.

Measurement Terminals

Input

Channel A

Input

Channel B

External

power

supply

Table des matières

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur