ADTRAN T400 Guide de maintenance et de service

1Section 61213017L1-5, Issue 261213.017L1-5B

Section 61213017L1-5

Issue 2, September 1996

CLEI Code #DDRPHJA1_ _

PRACTICES

Figure 1. T400 U-RPM III

C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

Sealing Current Generation

The T400 U-RPM III converts -48 or -72 VDC input

voltage to provide an output voltage of up to -120 VDC,

andupto43mAofsealingcurrent. Whenusedwiththe

ADTRAN ISDN U-Repeater II and III, the U-RPM III

operatesinaconstantcurrentmode,allowingtheoutput

voltage to change depending on the loop resistance

between the U-RPM and the U-Repeater. In this mode,

the U-RPM III provides the required constant 43 mA

sealing current, with output voltages ranging from -28

VDCto-120VDC. WhenusedwiththeADTRANI-NIU,

the U-RPM III operates in a constant voltage mode,

providing a constant -120 VDC. The output current will

bebetween10and30mA,dependantonloopresistance

between the I-NIU and the U-RPM III. The U-RPM III

automaticallydeterminesthecorrectmodeofoperation,

and does not require option selections.

1. GENERAL

The ADTRAN Type 400 U-Repeater Powering Module

III (T400 U-RPM III) is a T400 card used to power an

ADTRAN ISDN U-Repeater II, U-Repeater III, or the

ADTRAN I-NIU. Figure 1 is an illustration of the unit. It

canbe deployedinanystandard T400singleor multiple

housing, and is physically located between the U-

Repeater or I-NIU and the ISDN interface, such as an

ISDN switch or U-BRITE, as shown in Figure 2. The U-

RPM III can also be deployed in a Metallic Facilities

Termination (MFT) mounting when used with an

appropriately wired T400/MFT Adapter.

Revision History

Issue 3 has been revised to incorporate the ADTRAN I-

NIU functionality.

Features

The T400 U-RPM III, part number 1213017L1, features:

• Class A3 (-120 V) output voltage operation

• Battery return or earth ground option

• Front Panel LED indicating loop fault

• Passive transmission of data between U-LT and U-

Repeater

• Loop resistance monitoring from power module to U-

Repeater

• Factory replaceable fuse on input voltage line to

isolate from shelf

T400 U-RPM III

U-REPEATER III POWERING MODULE

INSTALLATION/MAINTENANCE

CONTENTS

1. GENERAL ......................................................................1

2. INSTALLATION .............................................................2

3. WARRANTY AND CUSTOMER SERVICE ...................3

FIGURES

Figure 1. T400 U-RPM III ..................................................1

Figure 2. T400 U-RPM III Application ...............................2

Figure 3. Connector Pin Assignments...............................2

2 Section 61213017L1-5, Issue 2 61213.017L1-5B

2. INSTALLATION

After unpacking the unit, immediately inspect it for

possibleshippingdamage. Ifdamageisdiscovered,file

a claim immediately with the carrier, then contact

ADTRAN Customer Service (see section 3,

Warranty

and Customer Service

Select the appropriate grounding option for the U-RPM

III's faceplate using Jumper J1. The faceplate can be

grounded to either the -48V return (A and B) or frame

ground (B and C). When frame ground is selected,

backplaneconnectorpins11or27mustbeconnectedto

Frame /Chassis ground of the housing.

Grasp the T400 U-RPM III by the faceplate and insert it

into a shelf slot. Push the T400 U-RPM III into the

backplane connector until firmly seated.

Voltages to -120 VDC may be present on

output to repeater when the unit is powered.

After installing the U-RPM III and the U-Repeater or I-

NIU, refer to the

appropriate ADTRAN U-Repeater

Installation/Maintenance

practice for installation

verification.

Figure 3 shows the connector pin assignments. All

connections to the unit are made through the T400-

compatible backplane. No additional backplane wiring

is necessary for normal operation.

Figure 2. T400 U-RPM III Application

Figure 3. Connector Pin Assignments

Top

View from

Pin End

Component

Side

-48 V / -72V

FRM GND

-48R

FRM GND

To/From

Office

To/From

ADTRAN U-Repeater/I-NIU

MDF

T400

POWER

MODULE ADTRAN ISDN

U-REPEATER/I-NIU

U-RPM III

CURRENT

SOURCE

43 mA

U-INTERFACE

MAIN

DISTRIBUTION

FRAME

(41)

(47)

(7)

(13)

(11)

(27)

(17)

FRAME GND -48V/-72V BATTERY GND

Customer

NT1

Central Office

REPEATER

POWER

CONVERTER

(35)

ISDN SWITCH or

U-BR1TE

3Section 61213017L1-5, Issue 261213.017L1-5B

If using Frame ground option, backplane

connectorpins11or27must beconnectedto

earth ground.

TheT400U-RPMIIIcanbeinstalledin WesternElectric

MetallicFacilitiesTermination (MFT)mountingshelves.

TheuseofaT400/MFTadapterprovidesthemechanical

andelectrical interfacesrequiredfor properoperationof

theU-RPMIIIintheMFTmounting. T400/MFTAdapters

are available in either a custom wired or an unwired

model from multiple suppliers. The unwired versions

require wire-wrapping to interconnect the T400 56-pin

connectors to the MFT 40-connector.

LOOP FAULT

A faceplate-mounted LED labeled

LOOP FAULT

illuminateswhen theloopisopentotherepeater.

When

installed, the module dissipates approximately 2 watts.

3. WARRANTY AND CUSTOMER SERVICE

ADTRAN will replace or repair this product within ten

years from the date of shipment, if the product does not

meet its published specifications or if it fails while in

service. For detailed warranty, repair, and return

information, refer to the ADTRAN Equipment Warranty

and Return Policy and Procedure.

Return Material Authorization (RMA) is required prior to

returning equipment to ADTRAN. ADTRAN does not

recommend that repairs be performed in the field.

Forservice,RMArequests,orfurtherinformation,contact

one of the following numbers:

ADTRAN Customer Service:

Applications Engineering (800)615-1176

(Pre-Sales Support and Inquiries)

Technical Support (Post-Sales) (800)726-8663

(Have unit serial number available.)

Sales (800)827-0807

RMA (Repair Service) (205)971-8722

Repair and Return Address:

ADTRAN, Inc.

Customer Service Department

901 Explorer Boulevard

Huntsville, Alabama 35806-2807

Autres manuels pour T400

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ADTRAN Unité de contrôle

ADTRAN

ADTRAN GPON D OLT Manuel utilisateur

ADTRAN

ADTRAN Octal BRI/U Manuel utilisateur

ADTRAN

ADTRAN MX2820 Manuel utilisateur

ADTRAN

ADTRAN Modem-16 Module Manuel utilisateur

ADTRAN

ADTRAN Job Aid+ 1442707G3 Manuel utilisateur

ADTRAN

ADTRAN Job Aid+ 1442940G1 Manuel utilisateur

ADTRAN

ADTRAN E220 HFAC HDSL Mode d’emploi

ADTRAN

ADTRAN 1200222L1 Manuel utilisateur

ADTRAN

ADTRAN SFP+ 10G Manuel utilisateur

ADTRAN

ADTRAN Job Aid+ 1442704PG2 Manuel utilisateur

ADTRAN

ADTRAN IMUX-56 Manuel utilisateur

ADTRAN

ADTRAN jobAid+ SFP+ 11.3 G BIDI 20KM Manuel utilisateur

ADTRAN

ADTRAN Job Aid+ 1442981G8C Manuel utilisateur

ADTRAN

ADTRAN Job Aid+ 1442982G7C Manuel utilisateur

ADTRAN

ADTRAN Total Access 300 Series Manuel utilisateur

ADTRAN

ADTRAN Total Access 351 Series Manuel utilisateur

ADTRAN

ADTRAN T3 Manuel utilisateur

ADTRAN

ADTRAN Total Access Quad BNC Mode d’emploi

ADTRAN

ADTRAN Total Access 1500 FT1 DP Mode d’emploi

ADTRAN

ADTRAN Async-232 Manuel utilisateur

ADTRAN

ADTRAN Quad E1/PRA Manuel utilisateur

ADTRAN

ADTRAN Octal E&M Manuel utilisateur

ADTRAN

ADTRAN 1200261L1 Manuel utilisateur

ADTRAN

ADTRAN Total Access 1500 Mode d’emploi

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur