ADTRAN GPON D OLT Manuel utilisateur
Q
uick Star
t
DESCRIPTION
The GPON D OLT Small Form-factor Pluggable (SFP) is a single
fiber full duplex SFP. The SFP has a SC/UPC connector and is
designed for data links that employ high-speed burst mode TDM
receivers/transmitters.
This SFP supports the following features:
■Dual Wavelength Bidirectional Transceiver
■2488 Mbps Downstream
■1244 Mbps Upstream
■PRBS 223-1
■1310 nm APD/TIA Burst Mode Receiver
■1490 nm CW Mode DFB Laser
■ITU-T G.984.2 Complaint
■Single 3.3 V DC supply
■Low Power Consumption
■2x10 SFP Package Outline
■Single Fiber, Full Duplex Operation
■SC/UPC Optical Receptacle
Applications:
■Access networks
■Fiber to the home, curb, office (FTTx)
■Point to multi point service (P2MP)
♦ITU-T G.984.2
♦FSAN Class D
Due to compliance certification requirements, use only pluggable
optics supplied by ADTRAN. ADTRAN cannot certify system
integrity with other pluggable optics.
Installation
Before installing the equipment, inspect the SFP. If damage has
occurred during shipping, file a claim with the carrier, and then
contact ADTRAN Customer Support. For more information, refer
to the warranty.
To install the SFP into an appropriate module, complete the
following steps:
Do not remove the protective dust cover from the SFP until the
fiber optic cable is ready to be connected.
1. Insert the SFP into the SFP cage on the module. Ensuring
that the latch handle on the SFP is facing upward, slide the
SFP all the way into the SFP cage until there is an audible
“click”.
gNOTE
The latch on the SFP is for removal only. When removing the SFP,
rotate the latch away from the SFP, the SFP should easily slide
out of the cage.
2. Do not remove the protective dust cover until the optical fiber
connection is made.
gNOTE
ADTRAN recommends that the protective dust cover remain on
whenever the transceiver optical fiber connector is not inserted.
3. Continue the installation and turn-up of the host module
using the instructions in the Quick Start or Job Aid provided
with the module or other system-level documentation
available online at www.adtran.com.
Maintenance
The SFP does not require routine hardware maintenance for
normal operation. ADTRAN does not recommend that repairs be
attempted in the field. Repair services may be obtained by
returning the defective unit to ADTRAN. Refer to the warranty for
further information. Field support for software is provided through
upgrade facilities.
ADTRAN Pluggable Optics
SFP
GPON D OLT
October 2021
61442542F1C-13A
P/N: 1442542F1C
fWARNING!
WARNING indicates a hazard which, if
not avoided, could result in death, injury
or serious property damage.
fCAUTION!
CAUTION indicates a hazard which, if
not avoided, could result in service
interruption, damage to the equipment,
or minor property damage.
gNOTE
NOTES inform the user of additional, but
important, information or features.
261442542F1C-13A
SAFETY AND REGULATORY
fWARNING!
Read all warnings, cautions, notes, and installation instructions
before installing or servicing this equipment.
gNOTE
This product is a Class 1 Laser module that complies with FDA 21
CFR 1040.10, 1040.11 and IEC 60825-1. The product is NRTL
Listed and CB Certified to all applicable American and European
safety standards.
fCAUTION!
■Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing material
when transporting or storing. When working on modules,
always place them on an approved antistatic mat that is
electrically grounded.
■This product is intended for deployment in locations such as
telecommunications facilities (such as Central Offices) and at
locations where the NEC applies (such as customer
premises). This product is to be installed and serviced by
trained and qualified service personnel only. Care should be
taken to protect cables from damage or vandalism.
■This product and host system are designed and intended for
installation as part of a Common Bonding Network (CBN) or
Isolated Bonding Network (IBN).
■This product's outer case is "electrically isolated" from other
circuits, as a result, this product can be used in systems that
are installed either in a DC-I (isolated) or DC-C (common)
configuration. For Systems where other installed modules or
the host system itself have internal connections between
battery return and frame ground, the system can only be
deployed in a DC-C configuration.
■If the host system has a protective earth (PE) terminal, the PE
terminal of the host system must be connected to PE to ensure
that the exposed metal (front panels, optical modules) on the
product is properly grounded.
SPECIFICATIONS
Specifications for the SFP are as follows:
General
■Module Type: SFP
■Media Type: Fiber
♦Dual-Mode
♦Single-Fiber
♦Single strand fiber applications using SMF
■Optical Connector: SC/UPC
■Signal Data Rate:
♦Upstream: 1244 Mbps
♦Downstream: 2488 Mbps
■GPON and XGS-PON ODN Range configuration support:
(optical budget dependent)
♦Standard: 20 km
♦Extended: 37.5 km
♦Maximum: 60 km
■Optical Transmitter
♦Laser Diode Type: DFB
♦Transmit Wavelength: 1480 nm to 1500 nm
♦Tx Power: +6 dBm to +10 dBm
♦Spectral Width: 1 nm
♦SMSR: 30 dB
♦Extinction Ratio: 8.2 dB
■Receiver
♦Type: APD/TIA
♦Central Wavelength: 1260 nm to 1360 nm
♦Receiver Sensitivity: -33 dBm and –35 dBm (BER<10E-4)
♦Receiver Overload: –15 dBm
■Applications:
♦Access networks
♦Fiber to the home, curb, office (FTTx)
♦Point to multi point service (P2MP)
●ITU-T G.984.2
●FSAN Class D
Environmental
■Controlled Protected Environment (Indoor)
♦System Ambient Operational Temperature Range:
0°C to +55°C
♦Storage Temperature Range: -40°C to +85°C
♦Relative Humidity 5% to 95%, non-condensing
61442542F1C-13A 3
gNOTE
■This product is designed to be deployed in GR-3108-CORE
environmental class 1.
■This product is NRTL Listed to the applicable UL Standards.
The product is designed to meet the applicable requirements
of Telcordia GR-63-CORE, GR-3108-CORE, and GR-1089-
CORE.
■This product has been evaluated to applicable international
standards for CE marking.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
■This product is designed to meet the following environmental
classes:
♦ETSI EN 300 019-1-1 “Classification of environmental condi-
tions; Storage,” Class 1.2
♦ETSI EN 300 019-1-2 “Classification of environmental condi-
tions, Transportation,” Class 2.3
♦ETSI EN 300 019-1-3 “Classification of environmental condi-
tions, Stationary use at weather protected locations,” Class
3.1
■This product is designed to function without degradation during
exposure to all test severities per Class 3.1 of ETSI EN 300
019-1-3.
■This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/WEEE.
FRANÇAIS
fAVERTISSMENT!
Lisez toutes les mentions de danger et de prudence et les
remarques, ainsi que la notice d'installation, avant d'effectuer
l'installation ou l'entretien de cet équipement.
DEUTSCH
fWARNUNG!
Lesen Sie alle Warnungen, Gefahrenhinweise, Anmerkungen und
Installationsanweisungen bevor Sie dieses Gerät installieren oder
warten.
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
Copyright © 2021 ADTRAN, Inc. All Rights Reserved.
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442542F1C-13A*
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix
(online tool, go to: http://www.adtran.com/pluggableoptics)
Autres manuels ADTRAN Unité de contrôle
ADTRAN
ADTRAN Job Aid+ 1442981G8C Manuel utilisateur
ADTRAN
ADTRAN Job Aid+ 1442910G2 Manuel utilisateur
ADTRAN
ADTRAN Job Aid+ 1442704PG2 Manuel utilisateur
ADTRAN
ADTRAN U-BR1TE Mode d’emploi
ADTRAN
ADTRAN Total Access 351 Series Manuel utilisateur
ADTRAN
ADTRAN Total Access 300 Series Manuel utilisateur
ADTRAN
ADTRAN Quad E1/PRA Manuel utilisateur
ADTRAN
ADTRAN SFP Manuel utilisateur
ADTRAN
ADTRAN SFP Manuel utilisateur
ADTRAN
ADTRAN jobAid+ SFP+ 11.3 G BIDI 20KM Manuel utilisateur
ADTRAN
ADTRAN Octal Manuel utilisateur
ADTRAN
ADTRAN TRACER QUAD E1 Manuel utilisateur
ADTRAN
ADTRAN 1200315L1 Manuel utilisateur
ADTRAN
ADTRAN Job Aid+ 1442971GX Manuel utilisateur
ADTRAN
ADTRAN Total Access 1500 Mode d’emploi
ADTRAN
ADTRAN 1200065L1-1 Manuel utilisateur
ADTRAN
ADTRAN 1200222L1 Manuel utilisateur
ADTRAN
ADTRAN Octal BRI/U Manuel utilisateur
ADTRAN
ADTRAN E220 HFAC HDSL Manuel du produit
ADTRAN
ADTRAN Octal BRI S/T Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
