ADT QuickConnect Manuel d'utilisation et d'entretien

Battery Instructions:

Ademco Lynx & ADT QuickConnect

Compatible with:

Ademco Lynx

ADT QuickConnect

Instructions:

W H A T Y O U ’ L L N E E D :

•A registered MyADT Account

•1 small Phillips head screwdriver

•7.2V, 3700mAh battery

You can purchase a 7.2 Volt 3700 mAh battery from MyADT or from retailers such as Walmart,

Amazon, Batteries Plus, Home Depot, and Lowe’s. We also recommend checking with your local

retailers for availability. Here are the specifications of the 7.2 Volt 3700 mAh battery:

•Voltage: 7.2 V

•Capacity: 3700 mAh

•Terminals: Connector

•Chemistry: NiMH

•Length: 4”

Battery Instructions:

Ademco Lynx & ADT QuickConnect

•Width: 2.7”

•Height: 0.07”

•Weight: 0.30 lbs.

N O T E :

The battery pack is located inside the keypad. The battery pack has black and red wires coming out of

it with a modular connector at the end.

C A U T I O N :

Do not remove the green plastic cover from around the new battery pack. This covering is necessary

for a proper connection and may cause serious injury or damage if removed or damaged.

Battery Instructions:

Ademco Lynx & ADT QuickConnect

Step 1:

Set your system to Test Mode. Log into your MyADT account, click on the Alarm System tab, and select

System Test.

Step 2:

Unplug the control panel’s transformer from the outlet. You may need the screwdriver to remove the

retaining screw on the transformer.

Step 3:

Find the two tabs on top of your keypad, press them in to release the cover and gently pull the keypad

toward you.

Step 4:

Quickly inspect the old battery. If the battery looks abnormal (i.e. has a swollen or split case, liquid

leaking from the case, or corroded terminals) close the keypad and call (800) ADT-ASAP to schedule a

service call.

Battery Instructions:

Ademco Lynx & ADT QuickConnect

Step 5:

Remove the small screw from the plastic battery bracket. Be sure to put the screw in a place where you

won’t lose it since you’ll need it later.

Step 6:

Gently remove the wires from their retaining clips, and then disconnect the battery wires by pulling on

the plastic connector.

Battery Instructions:

Ademco Lynx & ADT QuickConnect

Then tip the top of the battery up to remove it from the compartment.

Step 7:

Remove the new battery from its packaging.

C A U T I O N :

Do not remove the green plastic cover from around the new battery pack. This covering is necessary

for a proper connection and may cause serious injury or damage if removed or damaged.

Step 8:

Place the new battery in the compartment and then screw in place the plastic battery bracket.

Step 9:

Thread the wires under the retaining clips, remove the protective plastic from the connector, and plug

it into the receptacle.

Step 10:

Replace the keypad, the two tabs snap back into place, and then plug the transformer back into the

outlet.

Battery Instructions:

Ademco Lynx & ADT QuickConnect

Step 11:

Check your alarm keypad to ensure it no longer displays the “BAT” or “SYSTEM LO BATTERY”

message. If it still shows a low battery message, try entering your code and pressing the OFF button.

Repeat if necessary. If the message still shows, it may take 24 to 48-hours for the battery to fully charge.

If after 48-hours the message still shows, please go to MyADT.com and start a Chat Session with us, or

call (800) ADT-ASAP to troubleshoot your system.

When the message is gone or you’re waiting for the battery to charge, remove your system from Test

Mode at MyADT.com.

Ensure your system is working properly by testing your system. Go to MyADT.com and place your

system on test and then follow the directions in the user guide to test your system or visit MyADT.com

to find your user guide

Table des matières

Autres manuels ADT Système de sécurité

ADT

ADT IGB-02 Manuel utilisateur

ADT

ADT Safewatch QuickConnect Plus Mode d'emploi

ADT

ADT Smart Home PM360-R Manuel utilisateur

ADT

ADT Safewatch Quick Connect Plus Manuel utilisateur

ADT

ADT Garda Response PM30 Manuel utilisateur

ADT

ADT Security System 4112 Manuel utilisateur

ADT

ADT ADT7AIO Series Manuel d'instructions

ADT

ADT 6160VPADT Instructions de montage

ADT

ADT FOCUS CADET Manuel utilisateur

ADT

ADT Entrepreneur 3000EN Mode d'emploi

ADT

ADT ACCORD XPC Manuel utilisateur

ADT

ADT BHS-3000C Manuel utilisateur

ADT

ADT DSC Impassa Manuel utilisateur

ADT

ADT ADTHYBWL Series Manuel utilisateur

ADT

ADT Safe-N-Go Manuel utilisateur

ADT

ADT SECURITY MANAGER 2000 Manuel utilisateur

ADT

ADT FOCUS CADET Manuel utilisateur

ADT

ADT Safewatch Manuel utilisateur

ADT

ADT Galaxy 8 Manuel utilisateur

ADT

ADT TSSC Instructions de montage

ADT

ADT Safewatch QuickConnect Plus Manuel utilisateur

ADT

ADT Security System 4112 Manuel utilisateur

ADT

ADT SASW3000EN Manuel utilisateur

ADT

ADT On-The-Go Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur