Addonics Technologies HDUSAS Manuel utilisateur

Technical Support

If you need any assistance to get your unit functioning properly, please have your

product information ready and contact Addonics Technical Support at:

Hours: 8:30 am - 6:00 pm PST

Phone: 408-453-6212

Email: http://www.addonics.com/support/query/

v3.1.11

User Guide

1:1 Duplicator

(HDUSAS)

T E C H N O L O G I E S

www.addonics.com

ENT

ESC

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

ENT

ESC

Diagram

ENT

ESC

Duplicator Panel

LCD

Scroll Up

Scroll Down

Executes Function

Cancels Function

Source

SATA Port

4-pin Floppy Power

Connector

Destination

SATA Port

Mounting Holes

(2 on each side)

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Quick Guide

Installing the 1:1 duplicator

Step 1

Insert the 1:1 duplicator into standard 5.25” drive bay.

Step 2

Connect the power cable from you system to the 4-pin floppy power connector.

Step 3

Connect the source drive to the source SATA port via SATA cable and the target

drives to the destination SATA port via SATA cable.

Step 4

Screw the duplicator into the drive bay with 4 screws (2 on each side).

Duplicating drive(s)

Make sure the source and target drives are connected to the proper ports.

When the duplicator is on, it will go through the steps below.

Step 1

Duplicator LED will light up and the device will beep.

Step 2

LCD will display initial steps:

1. Duplicator Ver: - Displays duplicator version

2. Initializing SDRAM

3. Detect Source/Target - Will detect the type of source/targets

4. Copy - Defaults to the first function which is to copy

Step 3

Once the duplicator gets to the copy menu, press ENT to begin copying. The

duplicator will auto-detect the drive and display its information on the LCD. Make

sure that the power LEDs of the flash reader are blinking, the blinking indicates

drive activity.

You can find the complete user manual of the 1:1 Duplicator panel on the driver

disk under user guides. You can also download it from our website at

www.addonics.com/support/user_guides/

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

ENT

ESC

Duplicator Panel

LCD

Scroll Up

Scroll Down

Executes Function

Cancels Function

The Duplicator has 6 functions to choose from:

1. Copy

2. Compare

3. PreScan Source

4. ReScan BUS

5. Source Size

6. Setup

7. USB Mode

6-1. Language

6-2. Copy Size

6-3. Startup Menu

6-4. Auto Compare

6-5. Copy with Size

6-6. Button Sound

6-7. Device Info

6-8. System Info

Within function 6, there are 8 Subfunctions

1. Copy

Make sure that the capacity of the target is equal or larger than the source.

Copies data directly from the source to the target.

Choose option 1 from the menu and press ENT to begin copying. The system will

auto detect the source/target and display info about the copying process. Once

the copying process is complete, the LCD will display Copy OK.

2. Compare

Compare is used to see if the data on the source is identical to the target after the

copy operation.

Choose option 2 and press ENT to begin comparison. The LCD will display

comparison progress info and once complete will display information about how

many comparisons were OK, how many failed and how many were different.

3. PreScan Source

PreScan is used to check if the source can be accessed properly. It also tests the

read speed of the source.

Choose option 3 and press ENT to begin scanning. The LCD will display scan

progress info and read speed. Once the scan is complete, the LCD will display

PreScan Ok.

4. ReScan Bus

ReScan Bus allows swapping the source or target in and out without having to

reboot the system.

Choose option 4 and press ENT to begin rescanning. The system will rescan the

source without the need to reboot.

5. Source Size

Source Size is used to show the capacity of the source.

Choose option 5 and press ENT. The LCD will display the capacity of the source.

6. Setup

Setup allows various system settings to be changed. There are 8 sub-options:

Language, Copy Size, Startup Menu, Auto Compare, Copy with Size, Button

Sound, Device Info and System Info.

Choose option 6 and the LCD will display the first option of the subfunctions.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Setup Functions

6-1. Language

Use this option to select the language of the system, by default it’s set at English.

6-2. Copy Size

This option is used to specify the size of the source for simplifying further copying

operations.

Press ENT on this option and the LCD will display Copy Size ALL. Use the up

and down arrow keys to change the copy size. The system will offer

corresponding percentages so the user can specify the amount to copy from the

source.

6-3. Startup Menu

This option allows the user to change the first option they see when they boot up

the system. By default, the first option is Copy.

To change this, press ENT and use the up and down arrows to choose other

options.

6-4. Auto Compare

This option toggles the systems ability to automatically compare the source and

target after a copy is complete.

By default it is set to OFF, use the up and down arrows to toggle between ON

and OFF.

6-5. Copy with Size

This option is used to make the capacity of the target hard drive the same as teh

source hard drive.

For example, you have a target hard drive with 250GB capacity and a source

hard drive with 80GB capacity. After the copying process is complet the capacity

of the target hard drive will be seen by a system as 80GB instead of 250GB.

6-6. Button Sound

This option toggles the button sound of the system.

By default it is set to ON, use the up and down arrows to toggle between ON and

OFF.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

6-7. Device Info

This option will diplay the details of everything connected to the controller.

6-8. System Info

This option will display the system information.

7. USB Mode

NOTE: Though this is an active menu option, we recommend you not use

this option since there is no USB connection for this unit. This duplicator is

a standalone unit.

Troubleshooting

LCD

If the LCD display is blank after the device is turned on, check if the power

cable is properly connected and that the power supply is on.

Error Message

If an operation is manually terminated by pressing ESC while the system is running

a copy operation or hardware diagnostics, an error message will show up on the

LCD. This may lead to an illegal operation and cause the device to stop reminding.

If this happens, restart the device.

Source/Target

If the duplicator is unable to read the source or target please check that the data

and power cables are properly connected. When making a copy please make sure

that you set the source correctly.

Keys

If pressing the keys on the front panel produces no response from the system,

the keys may have malfunctioned.

Startup/Shutdown

Do not suddenly turn off the power while the system is performing an operation.

After shutting down normally, wait a moment (usually around 2 seconds) before

restarting the system so it can run self-diagnostics.

www.addonics.com

Phone: 408-573-8580

Fax: 408-573-8588

Email: http://www.addonics.com/sales/query/

LCD Messages

Connecting with a HDD:

All data will be lost, format?

All data will be lost. Confirm formatting.

Delete Image in Partition xx?

Confirm the deleting of data image in partition xx.

Format?

Ask if you want to format.

Format OK!

The formatting has been completed.

HDD not Format!

The hard disk hasn’t been formatted yet.

HDD too small

The capacity of hard disk is too small.

HDD too small to handle image!

The hard disk hasn’t enough capacity to store the

data image (at least 5Gbytes).

Image Exists Overwrite?

There is a data image in the current partition.

Confirm the overwriting of data.

Image load Fail

The image isn’t successfully loaded from DVD to

the hard disk.

Image load OK

The image is successfully loaded from DVD to

the hard disk

No Image in Partition xx

There is no data image in partition xx.

No Valid HDD!

The system cannot find a hard disk.

Partition Damage

The partition is damaged.

Select HD First!

Select a formatted hard disk at first.

Verify Disk or Partition?

Do you want to verify the hard disk or just a

partition?

Verify Hard Disk Fail!

The hard disk is not verified successfully.

Firmware Update:

Check Sum Error!

The updated firmware has errors.

Flash ROM fail!

Data cannot be written into Flash ROM.

Invalid firmware

The disc doesn’t contain a valid firmware.

Last update F/W Fail!

The firmware is not updated successfully.

Last update F/W OK!

The firmware is updated successfully.

Searching F/W

The system is searching for a valid firmware.

Source can’t be Hard Disk!

During comparison the source cannot be hard

disk.

Table des matières

Autres manuels Addonics Technologies duplicateur de disques

Addonics Technologies

Addonics Technologies DGC3 Manuel utilisateur

Addonics Technologies

Addonics Technologies HDUSI325AES Manuel utilisateur

Addonics Technologies

Addonics Technologies DDU7SAS Manuel utilisateur

Addonics Technologies

Addonics Technologies ST5DVRE Manuel utilisateur

Addonics Technologies

Addonics Technologies UDFUDD7 Manuel utilisateur

Addonics Technologies

Addonics Technologies HD4SNH Manuel utilisateur

Addonics Technologies

Addonics Technologies UDFH15-C Manuel utilisateur

Addonics Technologies

Addonics Technologies HDUS11325DX Manuel utilisateur

Addonics Technologies

Addonics Technologies HDUS11SNDX Manuel utilisateur

Addonics Technologies

Addonics Technologies MSDU5 Manuel utilisateur

Addonics Technologies

Addonics Technologies ST5BDVES Manuel utilisateur

Addonics Technologies

Addonics Technologies DGBRC3 Manuel utilisateur

Addonics Technologies

Addonics Technologies UDFHNVM15 Manuel utilisateur

Addonics Technologies

Addonics Technologies DigiCopier III DGC3 Manuel utilisateur

Addonics Technologies

Addonics Technologies AEDVDCOPPM4U Manuel utilisateur

Addonics Technologies

Addonics Technologies ZHDUESA Manuel utilisateur

Addonics Technologies

Addonics Technologies M2MSHD9H-2S Manuel utilisateur

Addonics Technologies

Addonics Technologies ST55HPMXA Manuel utilisateur

Addonics Technologies

Addonics Technologies JD2-3SN25 Manuel utilisateur

Addonics Technologies

Addonics Technologies CFASTD5 Manuel utilisateur

Addonics Technologies

Addonics Technologies Jasper II JD2P3 Manuel utilisateur

Addonics Technologies

Addonics Technologies HDUS325DX Manuel utilisateur

Addonics Technologies

Addonics Technologies DDU3SAS Manuel utilisateur

Addonics Technologies

Addonics Technologies HDUSI325 Manuel utilisateur

Manuels duplicateur de disques populaires d'autres marques

Riso

Riso CV Series Manuel

MicroBoards Technology

MicroBoards Technology GX-2 Manuel utilisateur

Carry

Carry Pro118 Manuel utilisateur

CopyPro

CopyPro PowerPro II Manuel utilisateur

Primera

Primera Max Manuel utilisateur

Logicube

Logicube EchoPlus-NG Manuel utilisateur

Silca

Silca Delta 2000 SA Manuel utilisateur

Reflex7

Reflex7 Daisy Chain Series Manuel utilisateur

Vinpower Digital

Vinpower Digital SharkCopier DC Manuel utilisateur

Codonics

Codonics Virtua E Manuel utilisateur

Octave

Octave Copy Master II Manuel utilisateur

Kanguru

Kanguru U2-DVDDUPE-S Manuel utilisateur

StarTech.com

StarTech.com 8STSATDUP11 Manuel utilisateur

DUPLO SEIKO CORPORATION

DUPLO SEIKO CORPORATION Duprinter DP-460 Manuel utilisateur

Vinpower Digital

Vinpower Digital MiniLoader VDX-1 Manuel utilisateur

MicroBoards Technology

MicroBoards Technology Quic Disc QD-2 Manuel utilisateur

Telex

Telex SpinWise Manuel utilisateur

Aleratec

Aleratec 260206 Manuel utilisateur