ACTi ACM-3511 Manuel utilisateur

www.acti.com

ACTi

Knowledge Base

Category: Installation & Configuration Note

Sub-category: Application

Model: ACM-3511/ACM-3011

Firmware: N/A

Software: N/A

Author: Victor.Wang

Published: 2009/09/02

Reviewed: 2010/01/21

1

Tips for 3-Inch Dome Installation

Contents

Introduction

Installation of camera plate

Installation of camera

Installation of front cover

Future design and improvement

Introduction

Some customers have a problem with installing a 3 inches dome. After adjusting the viewing

angle, zoom or focus, the lens part will be moved again by the rubber and black plastic cover

when they closing the dome cover.The purpose of this document is to guide customer through

the procedures of installing a 3 inches dome efficiently.

Installation of camera plate

1. Use the drill template, and drill a hole with φ35 on the ceiling.

www.acti.com

2

2. Fasten the plate with the camera.

3. Mark on the plate in the direction of the ACTi logo. (the butterfly)

4. Put the camera under ceiling. Adjust the ACTi logo on the camera (the butterfly) toward

the area or object you want to shoot.

5. Mark on the ceiling in the direction of the ACTi logo (the butterfly).

www.acti.com

3

6. Remove the camera from the plate. Tighten the plate to ceiling with M4*20 screws. Make

sure the mark on the plate aims at the mark of step 5.

Installation of camera

7. Connect cables through the hole on the ceiling and plate, or on the side of

casing.

www.acti.com

4

8. Fasten the camera to ceiling by turning clockwise direction.

9. Insert the cable (power/Network/audio) through the mounting plate and

connect to the camera. Then use the little strap in bundled accessory to fasten

the network cable.

www.acti.com

5

10. Fasten the camera to the ceiling. The ACTi logo (the butterfly) should now be

toward to the area or object you want to shoot.

Installation of front cover

11. Remove the front cover

12. Adjust the zoom or focus of the lens. (the lens and the ACTi logo should align

and be toward the area or object you want to shoot)

www.acti.com

6

13. Once you finish the adjustment, pan the lens counterclockwise for around 90

degrees to aim to the arrow on the camera cover.

14. Fasten the front cover to the camera by turning clockwise direction as quickly as

possible. The lens would be moved back to align to the ACti logo.

www.acti.com

7

Future design and improvement

15. In the next generation dome products, the front cover will be fastened to

camera by screws. Since we don't need to turn the front cover, the lens won't be

moved after adjustment.

Future design of ACTi Indoor Dome

Future design of ACTi Outdoor Dome

Autres manuels pour ACM-3511

1

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels ACTi Caméra de sécurité

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur