ACME MEGA STROBE 5000 RGB Manuel utilisateur

MEGA STROBE 5000 RGB

LED-ST5000 RGB

User Manual

Please read the user manual before use

1 E

Table of Contents

1，Safety Information…………………………………………………. 2

2，Rear Panel…………………………………………………………. 4

3，Preparation for Use ………………………………………………...4

4，Main Function …………………………………………………….. 5

5，Remote Control…………………………………………………….13

6，Technical Specification…………………………………………….15

2 E

1. Safety Information

Warning: This product is for professional use only! It is not for

household use.

The LED-ST5000 RGB presents risks of lethal or severe injury due to fire

and heat, electric shock, ultraviolet radiation, and falls. Flashing light is

also known to trigger epileptic seizures in persons who are photosensitive.

Read this manual before powering or installing the fixture, follow the

safety precautions listed below and observe all warnings in this manual

and printed on the fixture.

Noted: high voltage in the LED board!

Super power strobes, so please avoid extended periods of

continuous flashing

To guard against electric shock

Do not remove the rear cover: there are no user-serviceable parts inside.

Always ground (earth) the fixture electrically.

Use only a source of AC power that complies with local building and electrical

codes and has both overload and ground-fault protection.

Do not expose the fixture to rain or moisture.

To guard against UV radiation, burns, and fire

Never operate the fixture with the front glass open, missing or damaged.

Do not stare directly into the light. Never look at an exposed LED while it is lit.

Never attempt to bypass the fuse. Always replace defective fuses with ones of the

specified type and rating.

Verify that the power feed cable is rated for the current draw of all connected

fixtures.

Keep all combustible materials (for example fabric, wood, paper) at least 0.5 meters

(20 inches) away from the fixture. Keep flammable materials well away from the

fixture.

Minimum distance to illuminated surface is 10 meters.

Provide a minimum clearance of 0.1 meters (4 inches) around air vents.

3 E

Never place filters or other materials over the front glass cover.

The exterior of the fixture can reach temperatures up to 120° C (248° F). Allow the

fixture to cool for at least 15 minutes before handling.

Do not modify the fixture or install other than genuine parts.

Do not operate the fixture if the ambient air temperature (Ta) exceeds 40° C (104°

F).

To guard against falls

When suspending the fixture above ground level, verify that the structure can hold

at least 10 times the weight of all installed devices.

Verify that all external covers and rigging hardware are securely fastened and use

an approved means of secondary attachment such as a safety cable.

Block access below the work area whenever installing or removing the fixture.

To guard against epileptic seizure

Do not operate the fixture near stairways.

Provide advance notice that strobe lighting is in use.

Avoid extended periods of continuous flashing, particularly at frequencies of 10 to

20 flashes per second.

4 E

2. Rear Panel

1, Circuit Breaker

2, Main Power

3. LED display

4, Menu /UP/DOWN/ Enter button

5, DMX signal/ Flash indicator

6, DMX input/output

3. Preparation for Use

Table1: Cord cap wirings

INSTALLATION

The LED-ST5000 RGB may be installed in any orientation. The mounting bracket

provides five 12 mm holes for direct fastening or attachment of rigging clamps.

To install the mounting bracket

1. Place the fixture face down on a table.

5 E

2. Place an aluminum washer on each mounting bracket stud.

3. Make clear the direction of left and right side of bracket and lock the screws. After

that, tighten one hand knob to lock the mounting bracket in one end of bracket.

4. MAIN FUNCTION

Press MENU button enter the function, then use UP/DOWN or MENU button

to select the function you want, final press ENTER button to confirm the

function you select. Wait for 30 seconds, it will return to main interface. If

you want back to main menu, please hold MENU button for 1 second. The

main menu as follow:

4.1 DMX 512 address setting

Select ADDR option and the display will blink, press ENTER button to

confirm your selection. You can check the current DMX address from LED

display. The DMX address can be changed by press UP/DOWN button and

then press ENTER button to confirm your selection. Wait for 30 seconds, it

will return to main interface. If you want back to main menu, please hold

6 E

MENU button for 1 second.

4.2 Channel mode setting

Select CHMD option, press ENTER button to confirm your selection. Change

the channel way (1/2/3/4/6/7) by press UP/DOWN button. Press ENTER

button to confirm your selection. Wait for 30 seconds, it will return to main

interface. If you want back to main menu, please press MENU button.

4.3 LED display setting

Select the LED option, press ENTER button to confirm your selection. You

can see the current ON/OFF status of LED display now. You can change its

status by press UP/DOWN button. Then press ENTER button to confirm your

selection. If you choose OFF, than the LED display will close without any

operation for I min. Wait for 30 seconds, it will return to main interface. If you

want back to main menu, please hold MENU button for 1 second.

4.4 LED display direction setting

Select DISP option, press ENTER button to confirm your selection. Select

the DISP / DSIP by press UP/DOWN button. Press ENTER button to confirm

your selection. Wait for 30 seconds, it will return to main interface. If you

want back to main menu, please hold MENU button for 1 second.

4.5 White Balance

Select BALA option, press ENTER button to confirm your selection. Select

the RED,GREE,BLUE by press UP/DOWN button, Press ENTER button to

confirm your selection, then adjust the current DMX address byUP/DOWN

button, and Press ENTER button to confirm.Or Wait for 30 seconds, it will

return to main interface. If you want back to main menu, please hold MENU

button for 1 second.

7 E

4.6 Test setting

Select TEST option, press ENTER button to confirm your selection. The

flash indicator will light up and the unit will test automatically. Wait for

several seconds self-test, it will return to main interface. If you want back to

main menu, please hold MENU button for 1 second.

4.7 Temperature

Select the LEMP, press ENTER button and the display will show the

temperature of unit. Wait for 30 seconds, it will return to main interface. If

you want back to main menu, please hold MENU button for 1 second.

4.8 Defaults

Select DEF option, press ENTER button, Use UP/DOWN button if you would

like reset defaults,or not. press ENTER button to confirm your

selection. If you want back to main menu, please hold MENU button for 1

second.

4.9 Check the version number

Select the VER, press ENTER button to confirm. You can see the current

version number now (b 10/v 10) and check them by UP/DOWN. Wait for 30

seconds, it will return to main interface. If you want back to main menu,

please hold MENU button for 1 second.

Channel Mode:

8 E

1 Channel Mode

Channel

Value

Function

0-5

Blackout

6-250

Flash rate, slow to fast

251-255

Continuous ”Blinder”effect

2 Channel Mode

Channel

Value

Function

0-5

Blackout

6-255

Flash rate, slow to fast

Flash intensity

0-5

Blackout

6-255

Minimum to maximum

3 Channel Mode

Channel

Value

Function

1Flash intensity

0-5

Blackout

6-255

Minimum to maximum

2Flash duration 0-255 0-650 ms@50 Hz AC, or 0-530 ms@60 Hz AC

3Flash rate

0-5

No flash (single flash with ch. 1)

6-255

0.5-25 Hz@50 Hz AC, or 0.6-30 Hz @60 Hz AC

9 E

4 Channel Mode

Channel

Value

Function

1Flash intensity

0-5

Blackout

6-255

Minimum to maximum

2Flash duration

0-255

0-650 ms@50 Hz AC, or 0-530 ms@60 Hz AC

3Flash rate

0-5

No flash (single flash with ch. 1)

6-255

0.5-25 Hz@50 Hz AC, or 0.6-30 Hz @60 Hz AC

Special effects

0-5

No effect

6-50

Ramp up

51-100

Ramp down

101-150

Ramp up-down

151-200

Lightning

201-255

Random

6 Channel Mode

Channel Value Function

1(R)Flash intensity

0-5

Blackout

6-255

Minimum to maximum

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ACME Projecteur

ACME

ACME Dynamic 25 Spin LED?GF25 Manuel utilisateur

ACME

ACME XPerior 700WZA Manuel utilisateur

ACME

ACME SUPER NOVA RGB Manuel utilisateur

ACME

ACME REFracted RLS 100 Manuel utilisateur

ACME

ACME Invincibled LED-767RGBWII Manuel utilisateur

ACME

ACME Super Splash Manuel utilisateur

ACME

ACME LED-ST2000 Manuel utilisateur

ACME

ACME MEGA STROBE 5000 Manuel utilisateur

ACME

ACME BW-545 Manuel utilisateur

ACME

ACME IM-5S-ELC Manuel utilisateur

ACME

ACME Dragonfly Manuel utilisateur

ACME

ACME CM-108 RGB Manuel utilisateur

ACME

ACME LP-900 Manuel utilisateur

ACME

ACME CP?64 BD15 Manuel utilisateur

ACME

ACME LED-LP400 Manuel utilisateur

ACME

ACME PAGEANT CM-600z Manuel utilisateur

ACME

ACME LED-GBF Manuel utilisateur

ACME

ACME LED-CTL6 Manuel utilisateur

ACME

ACME LED-737 Manuel utilisateur

ACME

ACME Butterfly quard Manuel utilisateur

ACME

ACME BARRAGE LED-247 Manuel utilisateur

ACME

ACME LED-ST50 Manuel utilisateur

ACME

ACME TS-300M CW Manuel utilisateur

ACME

ACME LED-4TC Manuel utilisateur

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Ledj

Ledj PERFORMER 36 RGB Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur