ACME LED-LP400 Manuel utilisateur

LED-LP400

User Manual

Please read it carefully before using



Contents



1. Safety Introductions ............................................................................................................2

2. Technical Specifications.......................................................................................................3

3. Installation ..........................................................................................................................3

4. How To Set The Fixture .......................................................................................................4

4.1 Control Panel.................................................................................................................4

4.2 Main Function ...............................................................................................................5

5. How To Control The Unit....................................................................................................8

5.1 Master/Slave Function ...................................................................................................9

5.2 DMX Controller.............................................................................................................9

6. DMX512 Configuration .....................................................................................................10

7. DMX512 Connections.......................................................................................................10

8. Troubleshooting ................................................................................................................11

9. Fixture Cleaning ................................................................................................................12



1. Safety Introductions

WARNING



Please keep this User Manual for future consultation. If you sell the unit to another user,

be sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

The unit is for indoor use only and use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

Disconnect mains power before fuse replacement or servicing.

Replace fuse only with the same type.

Make sure there are not flammable materials close to the unit while operating as it is fire

hazard.

Use safety cable when fixes this unit.

Maximum ambient temperature is TA: 40 and don’t operate it where the temperature is

higher than this.

There are no user serviceable parts inside the fixture. Do not open the housing or attempt

any repairs by yourself. In the unlikely event your fixture may require service, please

contact the nearest authorized technical assistance center and always use the same type

spare parts. .

Don’t connect the device to any dimmer pack or power pack.

Do not look directly at the LED light beam while the fixture is on.

The housing must be replaced if they are visibly damaged.

Do not touch any wire during operation as high voltage might be causing electric shock.

Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.



Direct sunlight can cause heat to build up inside of the unit, which will seriously damage

unit.



2. Technical Specifications

It can be operated by DMX512 control or can be used as an individual unit without

controller.

It can be linked together as many as required in master/slave mode, and perform the great

built-in programmed lighting shows triggered by music.

Please use a 3 pin XLR cable/plug when connecting them together.

It features different pre-programmed chase patterns.

2/3 Channel modes.

Voltage: AC 100V-240V,50/60Hz

LED: 400pcs

Power consumption󵽱26W

Fuse: T 6.3A

Dimension 406 x 356 x 114mm

Weight󵽱 6.2KG



3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit

when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of

the touch of people and has no one pass by or under it.

For230V50Hzpowersupply,maximumfixturesthatcanbeconnectedononepowercableis20;

For120V60Hzpowersupply,maximumfixturesthatcanbeconnectedononepowercableis12;



4. How To Set The Fixture

4.1 Control Panel



1.Display: Used to show the various menus and the selected functions;

2. Indicator LED:

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

COLOR TEMP. Flashing Max. power consumption of CW/WW

3. Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

4. Battery Switch: Used to connect or disconnect the battery power supply.

5. Dimmer Adjust Knob: Used to adjust lightness for the unit.

6. Color Adjust Knob: Used to adjust the color temperature from 3200k to 6500k,

7. DMX Output: For DMX512 link, use 3/5-pin XLR plug cable to link the next unit.

8. DMX Input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal

9. Mains Output: Used to provide power supply for the next machine.

10. Mains Input: Used to connect to supply mains power.



11. Safety Hook: Ensure the safety of the fixture installation.



4.2 Main Function

To select any functions, press the MENU button until the required one is shown on the display.

Select the function by the ENTER button and the display will blink. Use the DOWN and UP

button to change the mode. Once the required mode has been selected, press the ENTER

button to setup or it will automatically return to the main functions without any change after

idling 30 seconds. Back to the functions without any change press the MENU button.

The main functions are shown below:



DMX 512 Address

Press the MENU button up to when the is shown on the display. Press the ENTER

button and the display will blink. Use the DOWN and UP button to change the DMX 512

address. Once the address has been selected, press the ENTER button to setup or

automatically exit menu mode without any change after 8 seconds. Back to the previous

functions without any change press the MENU button.



Channel Mode

Press the MENU button up to when the is shown on the display. Press the ENTER

button and the display will blink. Use the DOWN and UP button to select the (2

channels) or (2 channels) or (3 Channels) mode. Once the mode has been

selected, press the ENTER button to setup or automatically exit menu mode without any

change after 8 seconds. To go back to the functions without any change press the MENU

button.

Manual Mode

Press the MENU button up to when the is shown on the display. Press the ENTER

button and the display will blink. Use the DOWN and UP button to select the or

or (dimmer) mode, press the ENTER button to confirm, use the UP and DOWN

button to adjust the value between 0 and 255, once select press the ENTER button to setup or

automatically exit menu mode without any change after 8 seconds. To go back to the

functions without any change press the MENU button.

DMX State

Press the MENU button up to when the is shown on the display. Press the ENTER

button and the display will blink. Use the DOWN and UP button to select the

(Master/Slave Mode)  Blackoutor ( remain the last state when exiting the

menu). Once select press the ENTER button to setup or automatically exit menu mode

without any change after 8 seconds. To go back to the functions without any change press the

MENU button.

LED display

Press the MENU button up to when the is shown on the display. Press the ENTER

button and the display will blink. Use the DOWN and UP button to select the (display

on) or (display off) mode. Once select, press the ENTER button to setup or exit menu

mode without any change after 8 seconds. Back to the functions without any change press the



MENU button again.

Display Inverse

Press the MENU button until the is blinking on the display. Use the DOWN and UP

button to select the (normal) or (inverse), press the ENTER button to setup.

Back to the functions without any change press the MENU button.

Auto Test

Press the MENU button up to when the is blinking on the display. Press the ENTER

button and the unit will run the built-in programmer for self-test. To go back to the functions

press the MENU button.

Fixture use time

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the number of working hours of the unit. To go back to the

functions press the MENU button.

Software version

Press the MENU button up to when the is blinking on the display. Press the ENTER

button and the display will show the version of software of the unit. To go back to the

functions press the MENU button again.



5. How To Control The Unit

You can operate the unit in two ways:

1. By master/slave function

2. By DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address setting

will be affected at once. Every time you turn the unit on, it will show type on the display. After

that the unit will be ready to receive DMX signal or run the built in programs.



5.1 Master/Slave Function

By linking the units in master/slave connection, the first unit will be master automatically. You

should set the master unit effect via its knobs, then the other units (slave) will lighting as the

same.

5.2 DMX Controller

An universal DMX controller to control the units, you have to set DMX address from 1 to 512

channel so that the units can receive DMX signal.

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX512 address.

Once the address has been selected, press and keep ENTER button pressed up to when the

display stops blinking or storing automatically 30 seconds later. To go back to the functions

without any change press the MENU button again.

If you use please refer to the following diagram to address your DMX512 channel for the first

4 units.



2channels:

3channels:



Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ACME Projecteur

ACME

ACME LED-GBF Manuel utilisateur

ACME

ACME PAGEANT CM-600z Manuel utilisateur

ACME

ACME LED-192RGB Manuel utilisateur

ACME

ACME REFracted RLS 100 Manuel utilisateur

ACME

ACME LED-ST2000 Manuel utilisateur

ACME

ACME LED-ST50 Manuel utilisateur

ACME

ACME LP-900 Manuel utilisateur

ACME

ACME LED-4TC Manuel utilisateur

ACME

ACME XPerior 700WZA Manuel utilisateur

ACME

ACME LED-737 Manuel utilisateur

ACME

ACME Invincibled LED-767RGBWII Manuel utilisateur

ACME

ACME TV PANEL200 Manuel utilisateur

ACME

ACME CP?64 BD15 Manuel utilisateur

ACME

ACME Super Splash Manuel utilisateur

ACME

ACME DMX 512 Manuel utilisateur

ACME

ACME BARRAGE LED-248 Manuel utilisateur

ACME

ACME MEGA STROBE 5000 RGB Manuel utilisateur

ACME

ACME BW-545 Manuel utilisateur

ACME

ACME LITE PANEL 900 LP-900 WW BD30 Manuel utilisateur

ACME

ACME CM-108 RGB Manuel utilisateur

ACME

ACME TS-300M CW Manuel utilisateur

ACME

ACME Dynamic 25 Spin LED?GF25 Manuel utilisateur

ACME

ACME Dragonfly Manuel utilisateur

ACME

ACME theatre spot 150 TS-150 CW Manuel utilisateur

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Ledj

Ledj PERFORMER 36 RGB Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur