Accton Technology VM2524 Manuel utilisateur

VDSL Switch-VS2512A

VDSL Splitter-VM2524

VDSL Splitter-VM2548

Installation Guide

VDSL Switch-VS2512A

VDSL Switch supporting 12 VDSL Lines, with 1 Slot for Optional Gigabit

Uplink, 10/100BASE-TX, or 100BASE-FX Modules

VDSL Splitter-VM2524

VDSL Splitter supporting 24 VDSL Lines

VDSL Splitter-VM2548

VDSL Splitter supporting 48 VDSL Lines

Accton is a trademark of Accton Technology Corporation. Other trademarks or brand names mentioned

herein are trademarks or registered trademarks of their respective companies.

International Headquarters

No. 1 Creation Road III,

Science-based Industrial Park

Hsinchu 300, Taiwan

Phone: +886-3-5770-270

Fax: +886-3-5770-267

Internet: support@accton.com.tw

Europe Headquarters

Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 4a,

08970 - Sant Joan Despí,

Barcelona, Spain.

Phone: +34-93-477-4920

Fax: +34-93-477-3774

Asia Pacific Headquarters

1 Claymore Drive

#08-05/06 Orchard Towers (Rear Block)

Singapore 229594

Phone: +65 238 6556

Fax: +65 238 6466

Internet: www.acctontech.com

No part of this document may be copied or reproduced in any form or by any means without the prior written

consent of Accton Technology Corporation.

Accton makes no warranties with respect to this documentation and disclaims any implied warranties of

merchantability, quality, or fitness for any particular purpose. The information in this document is subject to

change without notice. Accton reserves the right to make revisions to this publication without obligation to

notify any person or entity of any such changes.

VS2512A

VM2524

VM2548

E072002-R01

150000010100A

Accton Technology Corporation

Limited Warranty: Accton warrants all its products to be free of manufacturing defects in

workmanship and materials, under normal use and service, for the applicable warranty

term. All Accton products carry a standard 90-day limited warranty from the date of

purchase from Accton or its Authorized Reseller. Accton may, at its own discretion, repair

or replace any product not operating as warranted with a similar or functionally equivalent

product, during the applicable warranty term.

The standard limited warranty can be upgraded to a Limited Lifetime* warranty by

registering new products within 30 days of purchase from Accton or its Authorized

Reseller. Registration can be accomplished via the enclosed product registration card or

online via the Accton web site. Failure to register will not affect the standard limited

warranty. The Limited Lifetime warranty covers a product during the Life of that Product,

which is defined as the period of time during which the product is an “Active” Accton

product. A product is considered to be “Active” while it is listed on the current Accton price

list. As new technologies emerge, older technologies become obsolete and Accton will, at

its discretion, replace an older product in its product line with one that incorporates these

newer technologies. At that point, the obsolete product is discontinued and is no longer

an “Active” Accton product. A list of discontinued products is attached with the most

recent version being available on the support section of our web site

(http://www.acctontech.com

All products that are replaced become the property of Accton. Replacement products may

be either new or reconditioned. Any replaced or repaired product carries either a 30-day

limited warranty or the remainder of the initial warranty, whichever is longer. Accton is not

responsible for any custom software or firmware, configuration information, or memory

data of Customer contained in, stored on, or integrated with any products returned to

Accton pursuant to any warranty. Products returned to Accton should have any

customer-installed accessory or add-on components, such as expansion modules,

removed prior to returning the product for replacement. Accton is not responsible for

these items if they are returned with the product.

Customers must contact Accton for a Return Material Authorization number prior to

returning any product to Accton. Proof of purchase may be required. Any product

returned to Accton without a valid Return Material Authorization (RMA) number clearly

marked on the outside of the package will be returned to customer at customer’s

expense. Customers are responsible for all shipping charges from their facility to Accton.

Accton is responsible for return shipping charges from Accton to customer.

Limited Warranty

WARRANTIES EXCLUSIVE: IF AN ACCTON PRODUCT DOES NOT OPERATE AS

WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY SHALL BE REPAIR OR

REPLACEMENT OF THE PRODUCT IN QUESTION, AT ACCTON’S OPTION. THE

FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF

ALL OTHER. WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN

FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING

WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. ACCTON NEITHER ASSUMES NOR AUTHORIZES ANY

OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION

WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS.

ACCTON SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND

EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT

EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE,

NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS

TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED

USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR

TORT (INCLUDING NEGLIGENCE), SHALL ACCTON BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR

FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS

ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,

MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS

PRODUCTS, EVEN IF ACCTON OR ITS AUTHORIZED RESELLER HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

SOME COUNTRIES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES

OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR

CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,

WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL

BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.

* Accton will provide warranty service for up to three years following discontinuance from

the active Accton price list. Under the limited lifetime warranty, internal and external

power supplies, fans, and cables are covered by a standard one-year warranty from date

of purchase

Compliances

FCC - Class A

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause interference to

radio communications. It has been tested and found to comply with the limits for a Class A

computing device pursuant to Subpart B of Part 15 of FCC Rules, which are designed to

provide reasonable protection against such interference when operated in a commercial

environment. Operation of this equipment in a residential area is likely to cause

interference, in which case the user, at his own expense, will be required to take whatever

measures may be required to correct the interference. You are cautioned that changes or

modifications not expressly approved by the party responsible for compliance could void

your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) for RJ-45 connections - Category 3 or greater

for 10 Mbps connections, and Category 5 for 100 Mbps connections. For fiber optic

connections, you may use 50/125 or 62.5/125 micron multimode fiber or 9/125 micron

single-mode fiber.

Warnings: 1.Wear an anti-static wrist strap or take other suitable measures to prevent

electrostatic discharge when handling this equipment.

2. When connecting this hub to a power outlet, connect the field ground lead

on the tri-pole power plug to a valid earth ground line to prevent electrical

hazards.

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus as set out in the interference-causing equipment standard entitled

“Digital Apparatus,” ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux

appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur:

“Appareils Numériques,” NMB-003 édictée par le ministère des Communications.

Japan VCCI Class A

CE Mark Declaration of Conformance for EMI and Safety (EEC)

This information technology equipment complies with the requirements of the Council

Directive 89/336/EEC on the Approximation of the laws of the Member States relating to

Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain

voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the

compliance with these Directives, the following standards were applied:

Warning! Do not plug a phone jack connector in the RJ-45 port. This may damage this

device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!

Taiwan BSMI Class A

RFI Emission: • Limit class A according to EN 55022:1998

• Limit class A for harmonic current emission according to EN 61000-3-2/1995

• Limitation of voltage fluctuation and flicker in low-voltage supply system

according to EN 61000-3-3/1995

Immunity: • Product family standard according to EN 55024:1998

• Electrostatic Discharge according to EN 61000-4-2:1995

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

• Radio-frequency electromagnetic field according to EN 61000-4-3:1996

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC power

supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5:1995

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

• Immunity to conducted disturbances, Induced by radio-frequency fields:

EN 61000-4-6:1996 (0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to

EN 61000-4-8:1993

(1 A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations immunity test

according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%

Reduction @500 ms, >95% Reduction @5000 ms)

LVD: • EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997)

iii

Safety Compliance

Warning: Fiber Optic Port Safety

Avertissment: Ports pour fibres optiques - sécurité sur le plan optique

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit

Underwriters Laboratories Compliance Statement

Important! Before making connections, make sure you have the correct cord set. Check

it (read the label on the cable) against the following:

The unit automatically matches the connected input voltage. Therefore, no additional

adjustments are necessary when connecting it to any input voltage within the range

marked on the rear panel.

When using a fiber optic port, never look at the transmit laser while it is

powered on. Also, never look directly at the fiber TX port and fiber cable

ends when they are powered on.

Ne regardez jamais le laser tant qu'il est sous tension. Ne regardez

jamais directement le port TX (Transmission) à fibres optiques et les

embouts de câbles à fibres optiques tant qu'ils sont sous tension.

Niemals ein Übertragungslaser betrachten, während dieses

eingeschaltet ist. Niemals direkt auf den Faser-TX-Anschluß

und auf die Faserkabelenden schauen, während diese

eingeschaltet sind.

Operating Voltage Cord Set Specifications

120 Volts UL Listed/CSA Certified Cord Set

Minimum 18 AWG

Type SVT or SJT three conductor cord

Maximum length of 15 feet

Parallel blade, grounding type attachment plug rated 15 A, 125 V

240 Volts (Europe only) Cord Set with H05VV-F cord having three conductors with

minimum diameter of 0.75 mm2

IEC-320 receptacle

Male plug rated 10 A, 250 V

CLASS I

LASER DEVICE

DISPOSITIF LASER

DE CLASSE I

LASERGER

DER KLASSE I

ÄT

Wichtige Sicherheitshinweise (Germany)

1. Bitte lesen Sie diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine

Flüssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur

Reinigung.

4. Die Netzanschlu ßsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen

könnte Beschädigungen hervorrufen.

7. Die Belüftungsöffnungen dienen der Luftzirkulation, die das Gerät vor Überhitzung schützt.

Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.

8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.

9. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch

nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz

trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät

gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.

13. Öffnen sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur

von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer

qualifizierten Servicestelle zu überprüfen:

a. Netzkabel oder Netzstecker sind beschädigt.

b. Flüssigkeit ist in das Gerät eingedrungen.

c. Das Gerät war Feuchtigkeit ausgesetzt.

d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit

Hilfe dieser Anleitung keine Verbesserung erzielen.

e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden. Für einen

Nennstrom bis 6A und einem Gerätegewicht größer 3 kg ist eine Leitung nicht leichter als

H05VV-F, 3G, 0.75 mm2einzusetzen.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70 dB(A) oder

weniger.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Accton Technology Changer

Accton Technology

Accton Technology SwitcHub-2se Manuel utilisateur

Accton Technology

Accton Technology Fast EtherHub-12s Manuel utilisateur

Accton Technology

Accton Technology Zilla Dual-Speed Hub-3008R Manuel utilisateur

Accton Technology

Accton Technology Classic-2040 Manuel utilisateur

Accton Technology

Accton Technology EH2045S Manuel utilisateur

Accton Technology

Accton Technology Volare Sensor 2 Manuel utilisateur

Accton Technology

Accton Technology CheetaHub Power-3004E Manuel utilisateur

Accton Technology

Accton Technology 24/48 10/100 Ports + 2GE Manuel de programmation

Accton Technology

Accton Technology CheetahSwitch Workgroup-3627 Manuel utilisateur

Accton Technology

Accton Technology Cheetah iSharer-3010 Manuel utilisateur

Accton Technology

Accton Technology ES4512C Manuel de programmation

Accton Technology

Accton Technology Edge-Core ES4528V Manuel utilisateur

Accton Technology

Accton Technology CheetaHub Power-3008A Manuel utilisateur

Accton Technology

Accton Technology ES4710BD Manuel utilisateur

Accton Technology

Accton Technology 12se Manuel utilisateur

Accton Technology

Accton Technology SwitcHub-2s Manuel utilisateur

Accton Technology

Accton Technology USB204B Manuel utilisateur

Accton Technology

Accton Technology Fast EtherHub-8s Manuel utilisateur

Accton Technology

Accton Technology SuperSmart EtherHub-16se Manuel utilisateur

Accton Technology

Accton Technology CHEETAHUB POWER-3012A Manuel utilisateur

Accton Technology

Accton Technology SwitcHub-7s Manuel utilisateur

Accton Technology

Accton Technology EH3008D Manuel utilisateur

Accton Technology

Accton Technology ES3616 Manuel de programmation

Accton Technology

Accton Technology CheetaHub Power-3008P Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur