Abit IS-85 Manuel utilisateur

Introduction

Hardware Setup BIOS Setup Driver & Utility Appendix

IS-85

Motherboard

Intel Pentium 4/Celeron/Celeron D

Socket 775

Installation Instruction

The information in this document is subject to change without notice and does not represent a

commitment on part of the vendor, who assumes no liability or responsibility for any errors that may

appear in this manual.

No warranty or representation, either expressed or implied, is made with respect to the quality,

accuracy or fitness for any particular part of this document. In no event shall the manufacturer be

liable for direct, indirect, special, incidental or consequential damages arising from any defect or

error in this manual or product.

Product names appearing in this manual are for identification purpose only and trademarks and

product names or brand names appearing in this document are the property of their respective

owners.

No part of this manual may be reproduced, transmitted or transcribed without the expressed written

permission of the manufacturer and authors of this manual.

If you do not properly set the motherboard settings, causing the motherboard to malfunction or fail,

we cannot guarantee any responsibility.

ii IS-85

Introduction

Contents

1. Introduction..................................................................... 1-1

Hardware Setup BIOS Setup Driver & Utility Appendix

1.1 Features & Specifications .............................................................1-1

1.2 Motherboard Layout.....................................................................1-3

2. Hardware Setup ............................................................... 2-1

2.1 Choosing a Computer Chassis.......................................................2-1

2.2 Installing Motherboard .................................................................2-1

2.3 Checking Jumper Settings ............................................................2-2

2.3.1 CMOS Memory Clearing Header and Backup Battery ..............2-3

2.4 Connecting Chassis Components...................................................2-5

2.4.1 ATX Power Connectors ........................................................2-5

2.4.2 FAN Power Connectors ........................................................2-5

2.4.3 Front Panel Switches & Indicators Headers............................2-6

2.5 Installing Hardware......................................................................2-7

2.5.1 CPU Socket 775 ..................................................................2-7

2.5.2 DDR Memory Slots ............................................................2-10

2.5.3 Floppy and IDE Disk Drive Connectors ................................ 2-11

2.5.4 Serial ATA Connectors .......................................................2-12

2.5.5 Accelerated Graphics Port Slot............................................2-13

2.5.6 PCI Add-on Slots ...............................................................2-13

2.6 Connecting Optional Devices ......................................................2-14

2.6.1 Additional USB 2.0 Port Headers.........................................2-14

2.6.2 Internal Audio Connector ................................................... 2-14

2.6.3 Front Panel Audio Connection Header ................................. 2-15

2.7 Connecting I/O Devices.............................................................. 2-16

IS-85 iii

3. BIOS Setup....................................................................... 3-1

4. Driver & Utility ................................................................. 4-1

5. Appendix .......................................................................... 5-1

5.1 Troubleshooting (How to Get Technical Support?)..........................5-1

5.1.1 Q & A.................................................................................5-1

5.1.2 Technical Support Form ......................................................5-3

iv IS-85

Introduction

1. Introduction

1.1 Features & Specifications

CPU

• LGA775 Socket for Intel Pentium 4/Celeron/Celeron D Processor with 800/533MHz

FSB

• Supports Intel Hyper-Threading Technology

Chipset

• Northbridge: Intel 865G

• Southbridge: Intel ICH5

Memory

• 2X 184-pin DIMM slots support 2GB maximum memory capacity

• Supports Dual Channel DDR 400 Un-buffered Non-ECC memory

Graphics

• Integrated Intel Extreme Graphics 2

Serial ATA

• 2x SATA 1.5Gb/s

LAN

• Onboard 10/100Mb PCI controller

Audio

• Onboard 5.1-Channel Audio CODEC

Expansion Slots

• 1x AGP 8X slot

• 3x PCI slots

Internal I/O Connectors

• 1x Floppy port

• 2x UDMA 100/66/33 IDE connectors (each supports 2x IDE devices)

• 2x SATA 1.5Gb/s connectors

• 2x USB 2.0 headers (each supports 2x USB 2.0 ports)

• 1x FP-Audio header

• 1x CD-IN header

Rear Panel I/O

• 1x PS/2 mouse port

• 1x PS/2 keyboard port

• 1x Serial port

IS-85 1-1

• 1x Parallel port

• 1x VGA port

• 4x USB 2.0 ports

• 1x RJ-45 LAN port

• 1x Audio connector (Line-in, Line-out, MIC-in)

Miscellaneous

• mATX form factor (244mm x 244mm)

※ Specifications and information contained herein are subject to change without

notice.

1-2 IS-85

Introduction

1.2 Motherboard Layout

IS-85 1-3

1-4 IS-85

Hardware Setup

IS-85 2-1

2. Hardware Setup

In this chapter we will elaborate all the information you need upon installing this motherboard

to your computer system.

※ Always power off the computer and unplug the AC power cord before adding or

removing any peripheral or component. Failing to do so may cause severe

damage to your motherboard and/or peripherals. Plug in the AC power cord only

after you have carefully checked everything.

2.1 Choosing a Computer Chassis

• This motherboard carries a mATX form factor of 244 x 244 mm. Choose a chassis big

enough to install this motherboard.

• As some features for this motherboard are implemented by cabling connectors on the

motherboard to indicators and switches or buttons on the chassis, make sure your chassis

supports all the features required.

• If there is possibility of adopting some more hard drives, make sure your chassis has

sufficient power and space for them.

• Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O

shield of the chassis matches the I/O port configuration of this motherboard. You can find

an I/O shield specifically designed for this motherboard in its package.

2.2 Installing Motherboard

Most computer chassis have a base with

many mounting holes to allow the

motherboard to be securely attached, and at

the same time, prevent the system from

short circuits. There are two ways to attach

the motherboard to the chassis base:

1. use studs, or

2. use spacers

In principle, the best way to attach the board

is to use studs. Only if you are unable to do

this should you attach the board with spacers.

Line up the holes on the board with the mounting holes on the chassis. If the holes line up and

there are screw holes, you can attach the board with studs. If the holes line up and there are

only slots, you can only attach with spacers. Take the tip of the spacers and insert them into

the slots. After doing this to all the slots, you can slide the board into position aligned with slots.

After the board has been positioned, check to make sure everything is OK before putting the

chassis back on.

To install this motherboard:

1. Locate all the screw holes on

the motherboard and the

chassis base.

2. Place all the studs or spacers

needed on the chassis base

and have them tightened.

3. Face the motherboard’s I/O

ports toward the chassis’s rear

panel.

4. Line up all the motherboard’s

screw holes with those studs o

spacers on the chassis.

5. Install the motherboard with

screws and have them

tightened.

Face the chassis’s rear panel.

※ To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if

they are already fastened on the chassis base and are without mounting-holes

on the motherboard to align with.

2.3 Checking Jumper Settings

For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the

jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position.

SHORT OPEN OPEN

For 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging the jumper cap in.

Pin 1~2 SHORT Pin 2~3 SHORT

2-2 IS-85

Table des matières

Autres manuels Abit Carte mère

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur