ABB A3 Series Manuel utilisateur

Mounting hole pattern

Typical spacing shown. Automotive name plate

requires 2.5" spacing. Some accessories also

require additional spacing.

—

INSTRUCTION SHEET

A3P oil-tight push-pull operator

These instructions do not purport to cover

all details or variations in equipment nor

to provide for every possible contingency

to be met in connection with installation,

operation or maintenance. Should further

information be desired or should

particular problems arise that are not

covered sufficiently for the purchaser’s

purpose, the matter should be referred to

ABB Inc.

The contents of this instruction manual

shall not become part of or modify any

prior or existing agreement, commitment

or relationship. The sales contract

contains the entire obligation of ABB. The

warranty contained in the contract

between the parties is the sole warranty

of ABB. Any statements contained herein

do not create new warranties or modify

the existing warranty.

Cat. no.

A3PP4_ _

A3PP6__

A3PPM__

A 3P T4R _ _

A3PB4__

A3PB6_ _

A3PBE__

A3PBF_ _

—

Step 3

Disassemble before installation

Large gaskets

Index locking ring

—

Step 1

1.25

[31.8]

1.25

[31.8]

2.25

[57.2]

0.672

[17.1]

0.190

[4.8]

Ø1.210

[Ø30.7]

2.25

[57.2]

Small gasket

—

Step 2

Name plate (optional)

2 3⁄8"

Large

—

Name plates

115⁄16"

4⁄5"

Standard

4⁄5"

27⁄16"

Automotive

For replacement parts information or

an application guide, visit our website

at abb.com/low-voltage or contact

your ABB representative.

For more information on optional

mounting kits, name plates and

other accessories, visit

abb.com/low-voltage.

WARNING

Hazardous voltage. Can cause

death, serious personal injury

or property damage.

To avoid electrical shock, turn

off electrical power to controls

before performing installation

or maintenance.

Panel thickness range

(inches)

Gaskets

required

16 ga – 14 ga 3

(0.060 – 0.075)

13 ga – 10 ga 2

(0.090 – 0.135)

9 ga – 7 ga 1

(0.150 – 0.188)

—

Step 4

—

Step 5

—

Step 6a

—

Step 6b

Locknut wrench

Cat. no. A3XGLW

Assemble parts

shown. Leave the

lens and small

gasket off until

step #6.

—

Replacement bulb chart

Volts

Incandescent

bulb

LED lamp – single bulb

Red Green Yellow White Blue

6#755* A3XBL6R A3XBL6G A3XBL6Y A3XBL6W A3XBL6L

24 #757 A3XBL2R A3XBL2G A3XBL2Y A3XBL2Y A3XBL2L

120 N/A A3XBL4R A3XBL4G A3XBL4Y A3XBL4Y A3XBL4L

*Also flashing lamp #267

Tighten locking nut to 40 ± 2 in-lb [4.5 Nm] recommended torque.

Contact operation:

Torque contact block retaining screws to 8 – 10 in-lb [0.9 – 1.1 Nm]

Torque light module retaining screws to 4 – 5 in-lb [0.5 – 0.6 Nm]

Maintained push-pull

Normally open contacts — use A3XC10 contact block

Normally closed contacts — use A3XC01 contact block

Momentary push-pull (factory assembled)

Normally open contacts — use A3XC01 contact block (becomes normally open when assembled)

Normally closed contacts — use special A3XC1EL contact block which must be mounted last

Plastic lens

1. Place small gasket inside nut.

2. Insert mushroom head/pushbutton

into switch body.

3. Tighten securely by hand.

1SQC910006M0201, A5E50558178, April 2021

—

We reserve the right to make technical

changes or modify the contents of this

document without prior notice. With regard

to purchase orders, the agreed particulars

shall prevail. ABB Inc. does not accept any

responsibility whatsoever for potential

errors or possible lack of information in

this document.

We reserve all rights in this document

and in the subject matter and illustrations

contained therein. Any reproduction or

utilization of its contents – in whole or in

parts – is forbidden without prior written

—

USA

ABB Inc.

305 Gregson Drive

Cary, NC 27511

abb.com/low-voltage

Ce manuel convient aux modèles suivants

Autres manuels ABB Unité de contrôle

ABB

ABB OMD200 Guide de l'utilisateur

ABB

ABB Relion 630 Series Guide de démarrage rapide

ABB

ABB FSCA-01 Manuel d'installation

ABB

ABB LEANtouch 6x36/30M-500 Series Manuel utilisateur

ABB

ABB FPTC-01 Manuel utilisateur

ABB

ABB MPS-C 2000 Manuel utilisateur

ABB

ABB COM600 series 5.0 Manuel du produit

ABB

ABB MicroFlex e150 Manuel utilisateur

ABB

ABB WaveLINE 6731-21-500 Manuel utilisateur

ABB

ABB ACQ580-04 Manuel utilisateur

ABB

ABB Busch-ComfortTouch 9 Manuel utilisateur

ABB

ABB FEPL-02 Ethernet POWERLINK Manuel d'installation

ABB

ABB COM600 series Manuel utilisateur

ABB

ABB Relion REC670 Instructions d'utilisation

ABB

ABB FENA-01 Manuel d'installation

ABB

ABB FMBA-01 Manuel utilisateur

ABB

ABB ACS 800 Series Manuel utilisateur

ABB

ABB NMBA-01 Manuel d'installation

ABB

ABB RMBA-01 Manuel utilisateur

ABB

ABB ACS880-304 +A003 Series Manuel utilisateur

ABB

ABB RDIO-01 Manuel utilisateur

ABB

ABB EAS822 Manuel utilisateur

ABB

ABB ACS880-1604LC Manuel utilisateur

ABB

ABB LW 110 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur